Ticket: CM-6106
Reviewed By: roopa,scotte
Testing Done: ran ifupdown2 regression suite and hand tested
This patch prevents IP address assignment under vlan aware bridges.
This prevents some confusion because a bridge subinterface is required
for layer 3 termination.
Ticket: CM-6275
Reviewed By: roopa,dustin
Testing Done: Unit tested and ran complete ifupdown2 test suite
There are unnecessary calls to the ethtool module that cause some error messages to be printed.
We currently don't check ifaceobj.link_kind at the start
so this check was added.
If someone creates a new interface without setting link_kind, we still printed error message.
This patch adds a check at the start of ethtool.
This patch also removes the global link defaults (used by ifupdown2/ethtool)
created when update-ports is called. The defaults are created for each swp port
so we don't have defaults (and therefore will not attempt to set) for interfaces
like eth0, loopbacks, dummys, vxlans, or any other non swp interface.
Ticket: CM-5146
Reviewed By: roopa,jtoppins
Testing Done: built new ifupdown package and ran testifupdown2 suite of tests
This patch prevents enslaved interfaces from having IP addresses.
(cherry picked from commit 0c00606fbc76db11557a8e946310e93a2b376aa7)
(cherry picked from commit dc30987acfc6af356b9e055db95d94ae45f0de9f)
Ticket: CM-5254
Reviewed By: roopa
Testing Done: tested master and 2.5_br images with testifupdown2 suite and hand tested
This patch creates a json defaults file upon bootup
(which can be overridden by customer configs in /etc)
which the ethtool module in ifupdown2 will consult
when "link-x" configs are removed in order to restore
them to the initial settings used by the switch.
(cherry picked from commit 8388664f5a5a85f2a813cafbf40ac92d7b86f4bf)
Conflicts:
packages/cl-utilities/usrlib/update-ports
(cherry picked from commit 21c9c10ab2fccaf60be9accb337e82541d497cc4)
Ticket: CM-5105
Reviewed By: roopa
Testing Done: tested configs before and after change
We needed a configuration option to add vxlan-ageing to
ifupdown2 configs. This patch adds the option to change
the vxlan-ageing timer currently set with "ip link"
commands.
(cherry picked from commit 9832462c365bd2b900b98f5675d407d1b11c4a95)
Conflicts:
packages/ifupdown2/addons/vxlan.py
packages/ifupdown2/ifupdownaddons/iproute2.py
Ticket: CM-5887
Reviewed By: trivial
Testing Done: Tested with sample config in the bug
(cherry picked from commit e90149a1e8ea3bc94e07fb080361e6909b12e81b)
Ticket: CM-5924, CM-5937, CM-5921, CM-5932
Reviewed By: CCR-2911
Testing Done:
bonding driver:
- renamed bond lacp-bypass-use-priority config option to
lacp-bypass-all-active with the default value of 0
- ignore clag role when lacp-bypass-all-active is enabled
- added info logging of lacp bypass state changes
iproute2:
- renamed bond lacp-bypass-use-priority config option
ifupdown:
- renamed bond lacp-bypass-use-priority config option
- added default value handling for lacp bypass attributes
switchd:
- macs learned on individual slaves are now sync to kernel with
the bond's ifindex. This eliminates flooding when cpu is
communicating to the host where the bond is in lacp bypass
- fixed bond forwarding state propagation to individual slaves in
bypass
Ticket: CM-5832
Reviewed By: CCR-2875
Testing Done: Tested with test case in the bug and other orders
kernel(upstream and us) does not seem to honor the vidinfo flags
during the deletes. Hence, this reordering becomes necessary.
tested with the example in the bug and also some other examples.
code wise this combines two existing methods but leaves the two existing methods
around for future use. Will remove them if they become completely
unnecessary.
Ticket: CM-5693
Reviewed By: roopa
Testing Done: tested bridge and bonds with interfaces with configs
Both bridge and mstpctl modules set priv_flags on interfaces
that have configs (like link-speed) even when used as bridge-ports.
And this collision causes statemanager.ifaceobj_sync() to never get called
because ifaceobj.priv_flags is 1 (we return immediately):
The fix was to create a new iface module_flags array to carry module info.
Ticket: CM-5637
Reviewed By: CCR-2755
Testing Done:
Replaced vxlan-peernodeip attribute with vxlan-remoteip. Updated
the vxlan and iproute2 modules to configure head end replication
using bridge fdb commands.
Ticket: CM-5355
Reviewed By: roopa
Testing Done: Tested config in ticket
MTU settings are defaulted 1500 when interface is ifdowned.
This has the effect of changing the MTU on the interface and any subinterfaces to
1500. And if these subinterfaces are in a bridge, the bridge will pick the MIN MTU
so the bridge keeps this MTU even after the interface is brought back up. The sub
interface does not change to a higher value then 1500 (kernel VLAN driver only
moves the MTU is the decreasing direction.
handling.
Ticket: CM-4802
Reviewed By: CCR-2565
Testing Done: Yes
1. Earlier various clag components where using link admin state for enforcing
proto_down. With the introduction of a seperate proto_down state this is no
longer needed. Now on clag bond "proto_down" the bond and its slaves are
explicitly placed in a proto_down state. This carrier downs the slaves and
oper-downs the clag-bond. Change has been done in clagd, clag-monit script and
bonding driver.
2. Earlier misc tricks where needed in ifupdown2 to prevent slave state changes
for clag bond outside of clagd. These tricks are no longer needed and have been
reverted to keep ifupdown2 handling simple/consistent. This change basically
reverts #6985e1a376b538fbfa2346ef657427ae7e8f117a.
Ticket: CM-4859, CM-4382
Reviewed By:
Testing Done: Tested with config which included bond bridge ports with
zero address on the bond.
The bridge driver rejects the port add with -EINVAL.
A bond with no slaves is one usecase where the bond interface
has a zero hw address and is rejected by the bridge.
EINVAL currently is very confusing.
This patch checks for a valid ether add before enslaving the port to the
bridge.
Ticket: CM-4802
Reviewed By:
Testing Done: yes
1. clag_enable needs to be set before slaves are added to the bond. Otherwise
bonding driver will bring the slaves up independent of clagd.
2. also added post_down clagd addon to cleanup the clag-id on ifdown.
Ticket: CM-4802
Reviewed By: CCR-2507
Testing Done: Yes
1. For clag bonds the slaves are kept down under various conditions (when clagd
is holding the bond in an errDisabled state). ifupdown2 should not set the slave
states for clag bonds.
2. Bonding driver sets the slave states on enslave and release (also for
non-clag bonds) so ifupdown2 doesn't need to set the slave state.
Ticket: CM-4723
Reviewed By: CCR-2408
Testing Done: vxlan_fld_test.py:test_bond_vxlinux_convergence_flaps, manual testing
On tunnel delete, tunnel termination object in BCM sdk is not cleaned properly.
As a result, mpls_entry in the hardware is left around even though software has
deleted the tunnel. This prevents subsequent dynamic creation of the same tunnel
and also mac learning, as mpls_entry points to invalid SVP with no CML setting
to do hardware learning.
Also, changes in ifupdown2 to make "vxlan-learning on" as default, so that
user/script doesn't have to explicitly turn on the learning.
Ticket: CM-4639
Reviewed By:
Testing Done: Tested with interfaces file and steps from the bug
This is a Hack to make sure the primary address
is the first in the routing table. Its not a full proof solution.
We use `ip route get` on the vrr network to see which
device the kernel returns. if it is the mac vlan device,
flap the macvlan device to adjust the routing table entry.
flapping the macvlan device makes sure the macvlan
connected route goes through delete + add, hence adjusting
the order in the routing table.
1. clag_enable flag in the bonding driver
2. And clagid in clagd
Ticket: CM-4091
Reviewed By:
Testing Done: yes
1. Two new commands have been introduced in clagctl - setclagid and showclagid.
These commands will be used by ifupdown2 to set and read/check the clagid.
2. In addition a bit will be maintained per-bond in the bonding driver to
indicate if a bond is a CLAG bond.
(cherry picked from commit cb160bad45d330fe5f544d0d9a40c1c77b9b563f)
Ticket:
Reviewed By:
Testing Done: Yes
1. ifupdown2/bonding-driver changes to show/store clag-id (errDisabled/dormant states for bond slaves will follow in 2.5.1)
2. clagd changes for
a. --forceDynamic - clagid is ignored in this mode
b. (default) static mode - clagid is matched along with partner mac for dualConnection; also ad_sys_mac is only changed for clag bonds (bonds with a non-zero clag-id).
Conflicts:
patches/kernel/series
in vlan module to use rtnetlink api
Ticket: CM-4173
Reviewed By:
Testing Done: Tested new bridge driver svi up/down
This does not move all 'bridge vlan' commands to rtnetlink yet.
Ticket: CM-3346
Reviewed By:
Testing Done: Tested ifupdown2 sanity
- moved 'admin up' delays that we introduced recently to be
configurable via two ifupdown2.conf attributes
# Let link master (bridges, bonds) own the link state of slaves
link_master_slave=1
# Delay admin state change till the end
delay_admin_state_change=0
- reduced some redundant traversal of dependency trees
- fixed a few bugs in query check
issues with having it in flags) + add check for bond slave being already up
Ticket: CM-4408
Reviewed By:
Testing Done: some bond sanity test
(cherry picked from commit 346b62a41fbf4521008cd8a9b0fa227e75a5d994)
sure that slaves can never be brought admin up on their own when they
are not in the bond
Ticket: CM-4408
Reviewed By: CCR-2323
Testing Done: Tested ifup/ifdown of bond slaves and bond interface
This patch introduces:
- introduces 2 interface flags, LINK_MASTER and LINK_SLAVE.
- The bond module will set LINK_MASTER on the bond iface object
indicating that the bond module owns the link.
- Which means that all lower devices /slaves of the bond get their
link when the bond (aka LINK_MASTER) is processed in the bond module
- The module that queries dependencies propagates the LINK_SLAVE flags
on the dependents of LINK_MASTER.
- The scheduler now acts on the LINK_SLAVE flag. If LINK_SLAVE is set,
it skips setting admin 'up' on that interface. It also makes sure the
interface is not already in the bond.
ie if an interface is a LINK_SLAVE (bond slave in this case), admin
up will not be executed when the interface is not inside the bond.
(cherry picked from commit 84b5a07a4f7685c7ae2eac5892889d6c0e08b2eb)
sure that slaves can never be brought admin up on their own when they
are not in the bond
Ticket: CM-4408
Reviewed By: CCR-2323
Testing Done: Tested ifup/ifdown of bond slaves and bond interface
This patch introduces:
- introduces 2 interface flags, LINK_MASTER and LINK_SLAVE.
- The bond module will set LINK_MASTER on the bond iface object
indicating that the bond module owns the link.
- Which means that all lower devices /slaves of the bond get their
link when the bond (aka LINK_MASTER) is processed in the bond module
- The module that queries dependencies propagates the LINK_SLAVE flags
on the dependents of LINK_MASTER.
- The scheduler now acts on the LINK_SLAVE flag. If LINK_SLAVE is set,
it skips setting admin 'up' on that interface. It also makes sure the
interface is not already in the bond.
ie if an interface is a LINK_SLAVE (bond slave in this case), admin
up will not be executed when the interface is not inside the bond.
