[13:09:20] root:~ # ifquery -a
auto lo
iface lo inet loopback
auto eth0
iface eth0 inet dhcp
auto vlan1903
iface vlan1903
vlan-id 1903
vlan-raw-device bridge
ipv6-addrgen no
address-virtual-ipv6-addrgen no
address-virtual 00:00:5e:00:01:a3 2a06:c01:1:1903::1/64 fe80::1/64 185.98.123.1/24
auto bridge
iface bridge
bridge-ports swp1
[13:09:25] root:~ # ifup -a -v
info: loading builtin modules from ['/usr/share/ifupdown2/addons']
info: executing /var/lib/ifupdown2/hooks/get_reserved_vlan_range.sh
info: executing /sbin/sysctl net.bridge.bridge-allow-multiple-vlans
info: executing /bin/pidof mstpd
info: executing /bin/ip rule show
info: executing /bin/ip -6 rule show
info: address: using default mtu 1500
info: 'link_master_slave' is set. slave admin state changes will be delayed till the masters admin state change.
info: processing interfaces file /etc/network/interfaces
info: lo: running ops ...
info: netlink: ip link show
info: netlink: ip addr show
info: executing /bin/ip addr help
info: address metric support: KO
info: lo: netlink: ip link set dev lo up
info: reading '/proc/sys/net/mpls/conf/lo/input'
info: reading '/proc/sys/net/ipv4/conf/lo/forwarding'
info: reading '/proc/sys/net/ipv6/conf/lo/forwarding'
info: reading '/proc/sys/net/ipv4/conf/lo/accept_local'
info: executing /bin/systemctl is-enabled vxrd.service
info: eth0: running ops ...
info: executing /sbin/ethtool eth0
info: reading '/sys/class/net/eth0/speed'
info: reading '/sys/class/net/eth0/duplex'
info: eth0: netlink: ip link set dev eth0 up
info: dhclient4 already running on eth0. Not restarting.
info: reading '/proc/sys/net/mpls/conf/eth0/input'
info: reading '/proc/sys/net/ipv4/conf/eth0/forwarding'
info: reading '/proc/sys/net/ipv6/conf/eth0/forwarding'
info: reading '/proc/sys/net/ipv4/conf/eth0/accept_local'
info: swp1: running ops ...
info: executing /sbin/ethtool swp1
info: reading '/sys/class/net/swp1/speed'
info: reading '/sys/class/net/swp1/duplex'
info: executing /sbin/ethtool -s swp1 speed 1000 duplex full
info: reading '/proc/sys/net/mpls/conf/swp1/input'
info: reading '/proc/sys/net/ipv4/conf/swp1/accept_local'
info: bridge: running ops ...
info: bridge: netlink: ip link add bridge type bridge
info: bridge: apply bridge settings
info: bridge: set bridge-ageing 1800
info: bridge: set bridge-hashel 4096
info: bridge: set bridge-hashmax 4096
info: bridge: set bridge-mcstats on
info: reading '/sys/class/net/bridge/bridge/stp_state'
info: bridge: stp state reset, reapplying port settings
info: bridge: netlink: ip link set bridge type bridge with attributes
info: writing '1' to file /proc/sys/net/ipv6/conf/swp1/disable_ipv6
info: executing /bin/ip -force -batch - [link set dev swp1 master bridge
addr flush dev swp1
]
info: bridge: applying bridge port configuration: ['swp1']
info: bridge: swp1: set bridge-portprios 8
info: swp1: netlink: ip link set dev swp1: bridge slave attributes
info: executing /sbin/brctl showmcqv4src bridge
info: bridge: applying bridge configuration specific to ports
info: bridge: processing bridge config for port swp1
info: swp1: netlink: ip link set dev swp1 up
info: bridge: setting bridge mac to port swp1 mac
info: executing /bin/ip link set dev bridge address 90:e2:ba:2c:b1:96
info: executing /sbin/mstpctl showportdetail bridge json
info: executing /sbin/mstpctl showbridge json bridge
info: bridge: applying mstp configuration specific to ports
info: bridge: processing mstp config for port swp1
info: bridge: netlink: ip link set dev bridge up
info: reading '/proc/sys/net/mpls/conf/bridge/input'
info: executing /sbin/sysctl net.ipv4.conf.bridge.forwarding
info: executing /sbin/sysctl net.ipv6.conf.bridge.forwarding
info: executing /bin/ip -force -batch - [link set dev bridge down
link set dev bridge addrgenmode eui64
link set dev bridge up
]
info: reading '/proc/sys/net/ipv4/conf/bridge/accept_local'
info: vlan1903: running ops ...
info: vlan1903: netlink: ip link add link bridge name vlan1903 type vlan id 1903 protocol 802.1q
info: vlan1903: netlink: ip link set dev vlan1903 up
info: reading '/proc/sys/net/mpls/conf/vlan1903/input'
info: reading '/proc/sys/net/ipv4/conf/vlan1903/forwarding'
info: reading '/proc/sys/net/ipv6/conf/vlan1903/forwarding'
info: executing /bin/ip -force -batch - [link set dev vlan1903 down
link set dev vlan1903 addrgenmode none
link set dev vlan1903 up
]
info: vlan1903: netlink: ip link add link vlan1903 name vlan1903-v0 type macvlan mode private
info: executing /sbin/sysctl net.ipv6.conf.vlan1903-v0.accept_dad
info: executing /sbin/sysctl net.ipv6.conf.vlan1903-v0.accept_dad=0
info: executing /sbin/sysctl net.ipv6.conf.vlan1903-v0.dad_transmits
info: executing /sbin/sysctl net.ipv6.conf.vlan1903-v0.dad_transmits=0
info: executing /bin/ip -force -batch - [link set dev vlan1903-v0 addrgenmode none
link set dev vlan1903-v0 down
link set dev vlan1903-v0 address 00:00:5e:00:01:a3
link set dev vlan1903-v0 up
addr add 2a06:c01:1:1903::1/64 dev vlan1903-v0
addr add fe80::1/64 dev vlan1903-v0
addr add 185.98.123.1/24 dev vlan1903-v0
route del 2a06:c01:1:1903::/64 dev vlan1903-v0
route del fe80::/64 dev vlan1903-v0
route add 2a06:c01:1:1903::/64 dev vlan1903-v0 proto kernel metric 9999
route add fe80::/64 dev vlan1903-v0 proto kernel metric 9999
]
info: reading '/proc/sys/net/ipv4/conf/vlan1903/accept_local'
[13:09:29] root:~ #
[13:09:30] root:~ #
[13:09:30] root:~ # ifquery -a -c
auto lo
iface lo inet loopback
auto eth0
iface eth0 inet dhcp [pass]
auto vlan1903
iface vlan1903 [pass]
vlan-raw-device bridge [pass]
vlan-id 1903 [pass]
ipv6-addrgen no [pass]
address-virtual 00:00:5e:00:01:a3 2a06:c01:1:1903::1/64 fe80::1/64 185.98.123.1/24 [pass]
address-virtual-ipv6-addrgen no [pass]
auto bridge
iface bridge [pass]
bridge-ports swp1 [pass]
[13:09:33] root:~ #
[13:09:35] root:~ #
[13:09:35] root:~ # ifquery -a -r
auto vlan1903-v0
iface vlan1903-v0
ipv6-addrgen off
address 185.98.123.1/24
address 2a06:c01:1:1903::1/64
auto vlan1903
iface vlan1903
vlan-id 1903
vlan-protocol 802.1Q
vlan-raw-device bridge
ipv6-addrgen off
address-virtual 00:00:5e:00:01:a3 185.98.123.1/242a06:c01:1:1903::1/64
address-virtual-ipv6-addrgen off
auto bridge
iface bridge
bridge-vlan-stats off
bridge-mcstats 1
bridge-ports swp1
bridge-stp yes
mstpctl-portp2p swp1=auto
mstpctl-treeportcost swp1=20000
mstpctl-portautoedge swp1=yes
auto swp1
iface swp1
auto eth0
iface eth0 inet dhcp
auto lo
iface lo inet loopback
mtu 65536
[13:09:38] root:~ # ip -d link show vlan1903
20: vlan1903@bridge: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP mode DEFAULT group default
link/ether 90:e2:ba:2c:b1:96 brd ff:ff:ff:ff:ff:ff promiscuity 1
vlan protocol 802.1Q id 1903 <REORDER_HDR> addrgenmode none
[13:09:50] root:~ # ip -d link show vlan1903-v0
21: vlan1903-v0@vlan1903: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP mode DEFAULT group default
link/ether 00:00:5e:00:01:a3 brd ff:ff:ff:ff:ff:ff promiscuity 0
macvlan mode private addrgenmode none
[13:09:53] root:~ #
[13:09:56] root:~ # ip link set dev vlan1903-v0 addrgenmode eui64
[13:10:23] root:~ # ifquery -a -c
auto lo
iface lo inet loopback
auto eth0
iface eth0 inet dhcp [pass]
auto vlan1903
iface vlan1903 [fail]
vlan-raw-device bridge [pass]
vlan-id 1903 [pass]
ipv6-addrgen no [pass]
address-virtual 00:00:5e:00:01:a3 2a06:c01:1:1903::1/64 fe80::1/64 185.98.123.1/24 [pass]
address-virtual-ipv6-addrgen no [fail]
auto bridge
iface bridge [pass]
bridge-ports swp1 [pass]
[13:10:29] root:~ # ifquery -a -r
auto vlan1903-v0
iface vlan1903-v0
address 185.98.123.1/24
address 2a06:c01:1:1903::1/64
auto vlan1903
iface vlan1903
vlan-id 1903
vlan-protocol 802.1Q
vlan-raw-device bridge
ipv6-addrgen off
address-virtual 00:00:5e:00:01:a3 185.98.123.1/242a06:c01:1:1903::1/64
address-virtual-ipv6-addrgen on
auto bridge
iface bridge
bridge-vlan-stats off
bridge-mcstats 1
bridge-ports swp1
bridge-stp yes
mstpctl-portp2p swp1=auto
mstpctl-treeportcost swp1=20000
mstpctl-portautoedge swp1=yes
auto swp1
iface swp1
auto eth0
iface eth0 inet dhcp
auto lo
iface lo inet loopback
mtu 65536
[13:10:33] root:~ #
Signed-off-by: Julien Fortin <julien@cumulusnetworks.com>
When setting addrgenmode it is necessary to flap the macvlan
device. After flapping the device we also need to re-add all
the user configuration. The best way to add the user config
is to flush our internal address cache.
[10:12:10] root:~ # ifquery vlan1000
auto vlan1000
iface vlan1000
address 192.168.10.1/24
address fc00:10::1/64
address-virtual 00:00:5e:00:01:01 192.168.10.1/24 fc00:10::1/64 fe80::1/64
vlan-id 1000
vlan-raw-device bridge
[10:12:15] root:~ # ifup -a
[10:12:24] root:~ # echo $?
0
[10:12:26] root:~ # ifquery vlan1000 -c
auto vlan1000
iface vlan1000 [pass]
vlan-raw-device bridge [pass]
vlan-id 1000 [pass]
address 192.168.10.1/24 [pass]
address fc00:10::1/64 [pass]
address-virtual 00:00:5e:00:01:01 192.168.10.1/24 fc00:10::1/64 fe80::1/64 [pass]
[10:12:30] root:~ # ip -6 -o addr show vlan1000-v0
48: vlan1000-v0 inet6 fc00:10::1/64 scope global \ valid_lft forever preferred_lft forever
48: vlan1000-v0 inet6 fe80::200:5eff:fe00:101/64 scope link \ valid_lft forever preferred_lft forever
48: vlan1000-v0 inet6 fe80::1/64 scope link \ valid_lft forever preferred_lft forever
[10:12:33] root:~ #
[10:12:34] root:~ #
[10:12:34] root:~ # ifquery vlan1000
auto vlan1000
iface vlan1000
address 192.168.10.1/24
address fc00:10::1/64
address-virtual 00:00:5e:00:01:01 192.168.10.1/24 fc00:10::1/64 fe80::1/64
address-virtual-ipv6-addrgen off
vlan-id 1000
vlan-raw-device bridge
[10:12:39] root:~ #
[10:12:41] root:~ # ifreload -a -d
...
debug: vlan1000: up : running module addressvirtual
debug: vlan1000-v0: reset address cache <<<<<<<<<<<<<<<<<<<<<< without this reset ifupdown2 would be in a broken state
info: vlan1000: checking route entry ...
info: executing /bin/ip route get 192.168.10.0/24
info: netlink: ip link show dev vlan1000
info: netlink: ip link show dev vlan1000-v0
info: vlan1000-v0: netlink: ip link set dev vlan1000-v0 up
info: executing /bin/ip -force -batch - [link set dev vlan1000-v0 down
link set dev vlan1000-v0 addrgenmode none
link set dev vlan1000-v0 up
addr add 192.168.10.1/24 dev vlan1000-v0
addr add fc00:10::1/64 dev vlan1000-v0
addr add fe80::1/64 dev vlan1000-v0
]
...
[10:12:50] root:~ #
[10:12:51] root:~ # ip -6 -o addr show vlan1000-v0
48: vlan1000-v0 inet6 fc00:10::1/64 scope global \ valid_lft forever preferred_lft forever
48: vlan1000-v0 inet6 fe80::1/64 scope link \ valid_lft forever preferred_lft forever
[10:12:53] root:~ # ifquery vlan1000 -c
auto vlan1000
iface vlan1000 [pass]
vlan-raw-device bridge [pass]
vlan-id 1000 [pass]
address 192.168.10.1/24 [pass]
address fc00:10::1/64 [pass]
address-virtual 00:00:5e:00:01:01 192.168.10.1/24 fc00:10::1/64 fe80::1/64 [pass]
[10:13:03] root:~ # echo $?
0
[10:13:04] root:~ #
Reviewed-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: Julien Fortin <julien@cumulusnetworks.com>
This commit adds support to configure and check gretap tunnels. An example
configuration could look like this:
iface tap0 inet tunnel
mode gretap
local 10.132.255.3
endpoint 10.132.255.1
ttl 64
mtu 1400
tunnel-physdev eth0
#
address 10.10.0.1/2
ifup will happily configure the interface (which it does even without this
patch) and ifquery now can successfully validate the configure interface:
cr03.in.ffho.net:~# ifquery -c tap0
iface tap0 inet tunnel [[ OK ]]
tunnel-physdev eth0 [[ OK ]]
endpoint 10.132.255.1 [[ OK ]]
local 10.132.255.3 [[ OK ]]
mode gretap [[ OK ]]
ttl 64 [[ OK ]]
mtu 1400 [[ OK ]]
address 10.10.0.1/24 [[ OK ]]
Signed-off-by: Maximilian Wilhelm <max@sdn.clinic>
This commit adds support for configuring GRE/IPIP/SIT tunnel interfaces as know
from previous versions of ifupdown. Currently only configuration checks for GRE
and SIT tunnels are implemented.
A tunnel interface configuration could look like this:
auto gre42
iface gre42 inet tunnel
mode gre
local 198.51.100.1
endpoint 203.0.113.2
#
# optional tunnel attributes
ttl 64
mtu 1400
tunnel-physdev eth0
#
address 192.0.2.42/31
address 2001:db8:d0c:23::42/64
auto he-ipv6
iface he-ipv6 inet tunnel
mode sit
endpoint 203.0.113.6
local 198.51.100.66
#
# optional tunnel attributes
ttl 255
mtu 1466
tunnel-physdev vrf_external
#
address 2001:db8:666::2/64
Signed-off-by: Maximilian Wilhelm <max@rfc2324.org>
backporting the following commit to master-next:
commit eb92e5efff
Author: Maximilian Wilhelm <max@rfc2324.org>
Date: Thu Oct 6 19:22:06 2016 +0200
Add support for setting phys-dev for VXLAN interfaces.
Add interface configuration option »vxlan-physdev« to set »dev« attribute
of VXLAN interfaces and a check for the running configuration.
Signed-off-by: Maximilian Wilhelm <max@rfc2324.org>
This backport also:
- adds support for ifquery --running
- uses the netlink cache
- includes some pep8 fixes
Signed-off-by: Julien Fortin <julien@cumulusnetworks.com>
Signed-off-by: Maximilian Wilhelm <max@rfc2324.org>
Co-authored-by: Julien Fortin <julien@cumulusnetworks.com>
Co-authored-by: Maximilian Wilhelm <max@rfc2324.org>
This is a major update coming all at once from master-next branch
master-next branch was started with --orphan option which is basically a new
branch without history.
The major changes are:
- repackaging
- cleanup the directory tree
- rewritte setup.py to allow install from deb file or pypi (pip install)
- add a Makefile to make things (like building a deb) easier
- review all debian files
Signed-off-by: Julien Fortin <julien@cumulusnetworks.com>
