update foundry mibs

git-svn-id: http://www.observium.org/svn/observer/trunk@3250 61d68cd4-352d-0410-923a-c4978735b2b8

mibs/BGP4V2-TC-MIB

@@ -0,0 +1,66 @@
+BGP4V2-TC-MIB DEFINITIONS ::= BEGIN
+
+    IMPORTS
+        mib-2, MODULE-IDENTITY FROM SNMPv2-SMI
+        TEXTUAL-CONVENTION FROM SNMPv2-TC;
+
+        bgp4V2TC MODULE-IDENTITY
+            LAST-UPDATED "201002010000Z"
+            ORGANIZATION "IETF IDR Working Group"
+            CONTACT-INFO "E-mail:  idr@ietf.org"
+
+            DESCRIPTION
+                    "Textual conventions for BGP-4.
+                     Copyright (C) The IETF Trust (2010).  This
+                     version of this MIB module is part of RFC XXX;
+                     see the RFC itself for full legal notices."
+-- RFC Editor - replace XXX with RFC number
+
+            REVISION "201002010000Z"
+            DESCRIPTION
+                   "Initial version."
+            ::= { mib-2 100}
+
+    --
+    -- Textual Conventions
+    --
+
+    Bgp4V2IdentifierTC ::= TEXTUAL-CONVENTION
+        DISPLAY-HINT "1d."
+        STATUS       current
+        DESCRIPTION
+            "The representation of a BGP Identifier.  BGP Identifiers
+             are presented in the received network byte order.
+
+             The BGP Identifier is displayed as if it is an IP address,
+             even if it would be an illegal one."
+        REFERENCE
+            "RFC 4273, Section 4.2"
+        SYNTAX OCTET STRING(SIZE (4))
+
+    Bgp4V2AddressFamilyIdentifierTC ::= TEXTUAL-CONVENTION
+        STATUS       current
+        DESCRIPTION
+            "The representation of a BGP AFI.  The value of this object
+             should be restricted to be between the values of 0 and 65535."
+        REFERENCE
+            "RFC 4760, Section 3"
+        SYNTAX INTEGER {
+                ipv4(1),
+                ipv6(2)
+            }
+
+    Bgp4V2SubsequentAddressFamilyIdentifierTC ::= TEXTUAL-CONVENTION
+        STATUS       current
+        DESCRIPTION
+            "The representation of a BGP SAFI"
+        REFERENCE
+            "RFC 4760, Section 3.  The value of this object should be
+             restricted to be between the values of 0 and 255."
+        SYNTAX INTEGER {
+                unicast(1),
+                multicast(2),
+                mpls(4)
+            }
+
+END

mibs/BRCD-DOT1X-MIB

@@ -0,0 +1,590 @@
+BRCD-DOT1X-MIB DEFINITIONS ::= BEGIN
+
+IMPORTS
+	MODULE-IDENTITY, OBJECT-TYPE, Integer32, Counter32, Unsigned32
+	   	FROM SNMPv2-SMI				-- [RFC2578]
+	ifIndex
+	   	FROM IF-MIB					-- [RFC2863]
+	MacAddress
+	   	FROM SNMPv2-TC				-- [RFC2579]
+       InetAddressType, InetAddress
+       	FROM INET-ADDRESS-MIB		-- [RFC4001]
+	EnabledStatus
+		FROM P-BRIDGE-MIB
+       SnmpAdminString
+        	FROM SNMP-FRAMEWORK-MIB; 	-- [RFC3411]
+
+brcdDot1xAuth MODULE-IDENTITY
+	LAST-UPDATED "201009300000Z" -- September 30, 2010
+	ORGANIZATION "Brocade Communications Systems, Inc."
+	CONTACT-INFO
+		"Technical Support Center
+              130 Holger Way,
+              San Jose, CA  95134
+              Email:  ipsupport@brocade.com
+              Phone: 1-800-752-8061
+              URL:  www.brocade.com"
+	DESCRIPTION
+		"Management Information for configuration /querying of 802.1x authentication
+			It is grouped into five MIBs -
+			1. Global level configurable admin /status 802.1x information
+			2. Port level EAPOL statistics information
+			3. Port level configuration information
+			4. Different Port state information and
+			5. 802.1x mac session information
+		Copyright 1996-2010 Brocade Communications Systems, Inc.
+  		All rights reserved.
+  		This Brocade Communications Systems SNMP Management Information Base Specification
+ 		embodies Brocade Communications Systems' confidential and proprietary
+ 		intellectual property. Brocade Communications Systems retains all
+  		title and ownership in the Specification, including any revisions.
+
+ 		This Specification is supplied AS IS, and Brocade Communications Systems makes
+ 		no warranty, either express or implied, as to the use,
+ 		operation, condition, or performance of the specification, and any unintended
+ 		consequence it may on the user environment."
+	REVISION     "201009300000Z" -- September 30, 2010
+	DESCRIPTION
+		""
+ ::= { iso(1) org(3) dod(6) internet(1) private(4) enterprises(1) foundry(1991) products(1) switch(1) snSwitch(3) 38 }
+-- -------------------------------------------------------------
+-- Textual Conventions
+-- -------------------------------------------------------------
+VlanId ::= TEXTUAL-CONVENTION
+    STATUS      current
+    DESCRIPTION
+        "A 12-bit VLAN ID used in the VLAN Tag header."
+    SYNTAX      INTEGER (1..4094)
+
+-- ---------------------------------------------------------- --
+-- groups in the Dot1x MIB
+-- ---------------------------------------------------------- --
+brcdDot1xAuthGlobalConfigGroup	OBJECT IDENTIFIER  ::=  { brcdDot1xAuth 1 }
+brcdDot1xAuthPortStatistics	OBJECT IDENTIFIER  ::=  { brcdDot1xAuth 2 }
+brcdDot1xAuthPortConfig		OBJECT IDENTIFIER  ::=  { brcdDot1xAuth 3 }
+brcdDot1xAuthPortState		OBJECT IDENTIFIER  ::=  { brcdDot1xAuth 4 }
+brcdDot1xAuthMacSession		OBJECT IDENTIFIER  ::=  { brcdDot1xAuth 5 }
+brcdDot1xAuthGlobalAdminGroup	OBJECT IDENTIFIER  ::=  { brcdDot1xAuth 6 }
+
+brcdDot1xAuthGlobalConfigQuietperiod	OBJECT-TYPE
+	SYNTAX			Unsigned32 (1..4294967294)
+	UNITS       		"seconds"
+	MAX-ACCESS		read-write
+	STATUS			current
+	DESCRIPTION		"When the Brocade device is unable to authenticate a Client,
+					the	amount of time the Brocade device waits before trying
+					again.. The allowed range is from 1 to 4294967294"
+	DEFVAL			{ 60 }
+	::= { brcdDot1xAuthGlobalConfigGroup 1 }
+
+brcdDot1xAuthGlobalConfigTxPeriod	OBJECT-TYPE
+	SYNTAX			Unsigned32 (1..4294967294)
+	UNITS       		"seconds"
+	MAX-ACCESS		read-write
+	STATUS			current
+	DESCRIPTION		"When a Client does not send back an EAP(Extensible
+					Authentication Protocol)-response/identity
+					frame, the amount of time the Brocade device waits before
+					retransmitting the EAP-request/identity frame to a Client
+					The allowed range is from 1 to 4294967294"
+	DEFVAL			{ 30 }
+	::= { brcdDot1xAuthGlobalConfigGroup 2 }
+
+brcdDot1xAuthGlobalConfigSuppTimeOut	OBJECT-TYPE
+	SYNTAX			Unsigned32 (1..4294967294)
+	UNITS       		"seconds"
+	MAX-ACCESS		read-write
+	STATUS			current
+	DESCRIPTION		"When a supplicant (Client) does not respond to an
+					EAP-request frame, the amount of time before the Brocade
+					device retransmits the frame
+					The allowed range is from 1 to 4294967294"
+	DEFVAL			{ 30 }
+	::= { brcdDot1xAuthGlobalConfigGroup 3 }
+
+brcdDot1xAuthGlobalConfigAuthServerTimeOut	OBJECT-TYPE
+	SYNTAX			Unsigned32 (1..4294967294)
+	UNITS       		"seconds"
+	MAX-ACCESS		read-write
+	STATUS			current
+	DESCRIPTION		"When the Authentication Server (RADIUS) does not respond
+					to a message sent from the Client, the amount of time before
+					the Brocade device retransmits the message.
+					The allowed range is from 1 to 4294967294"
+	DEFVAL			{ 2 }
+	::= { brcdDot1xAuthGlobalConfigGroup 4 }
+
+brcdDot1xAuthGlobalConfigMaxReq		OBJECT-TYPE
+	SYNTAX			Unsigned32
+	MAX-ACCESS		read-write
+	STATUS			current
+	DESCRIPTION		"The number of times the Brocade device retransmits an
+					EAP-request/identity request frame if it does not receive
+					an EAP-response/identity response frame from a Client"
+	DEFVAL			{ 2 }
+	::= { brcdDot1xAuthGlobalConfigGroup 5 }
+
+brcdDot1xAuthGlobalConfigReAuthMax		OBJECT-TYPE
+	SYNTAX			Unsigned32
+	MAX-ACCESS		read-write
+	STATUS			current
+	DESCRIPTION		"The number of re-authentication attempts that are
+					permitted before the port becomes Unauthorized"
+	DEFVAL			{ 2 }
+	::= { brcdDot1xAuthGlobalConfigGroup 6 }
+
+brcdDot1xAuthGlobalConfigReAuthPeriod	OBJECT-TYPE
+	SYNTAX			Unsigned32 (1..4294967294)
+	UNITS       		"seconds"
+	MAX-ACCESS		read-write
+	STATUS			current
+	DESCRIPTION		"How often the device automatically re-authenticates
+					clients when periodic re-authentication is enabled
+				 The allowed range is from 1 to 4294967294"
+	DEFVAL			{ 3600 }
+	::= { brcdDot1xAuthGlobalConfigGroup 7 }
+
+brcdDot1xAuthGlobalConfigProtocolVersion	OBJECT-TYPE
+	SYNTAX			Unsigned32
+	MAX-ACCESS		read-only
+	STATUS			current
+	DESCRIPTION		"The EAP protocol version"
+	 ::= { brcdDot1xAuthGlobalConfigGroup 8 }
+
+brcdDot1xAuthGlobalConfigTotalPortsEnabled	OBJECT-TYPE
+	SYNTAX			Unsigned32
+	MAX-ACCESS		read-only
+	STATUS			current
+	DESCRIPTION		"The total number of ports that have 802.1x enabled"
+	::= { brcdDot1xAuthGlobalConfigGroup 9 }
+
+brcdDot1xAuthGlobalConfigReauthStatus	OBJECT-TYPE
+	SYNTAX			EnabledStatus
+	MAX-ACCESS		read-write
+	STATUS			current
+	DESCRIPTION		"Used to enable / disable Reauthentication globally"
+	DEFVAL			{ disabled }
+	::= {brcdDot1xAuthGlobalConfigGroup 10 }
+
+brcdDot1xAuthGlobalConfigMacSessionMaxAge		OBJECT-TYPE
+	SYNTAX			Unsigned32
+	MAX-ACCESS		read-write
+	STATUS			current
+	DESCRIPTION		"The Max-Age of the 802.1x mac session-
+					A value between 0 and 65535"
+	::= {brcdDot1xAuthGlobalConfigGroup 11 }
+
+brcdDot1xAuthGlobalConfigNoAgingDeniedSessions	OBJECT-TYPE
+	SYNTAX				EnabledStatus
+	MAX-ACCESS			read-write
+	STATUS				current
+	DESCRIPTION			"Enable / Disable Mac-Session-No Aging
+						for Denied  sessions"
+	DEFVAL			{ disabled }
+	::= {brcdDot1xAuthGlobalConfigGroup 12 }
+
+brcdDot1xAuthGlobalConfigNoAgingPermittedSessions	OBJECT-TYPE
+	SYNTAX				EnabledStatus
+	MAX-ACCESS			read-write
+	STATUS				current
+	DESCRIPTION			"Enable / Disable Mac-Session-No Aging
+						for Permitted sessions"
+	DEFVAL			{ disabled }
+	::= {brcdDot1xAuthGlobalConfigGroup 13 }
+
+brcdDot1xAuthGlobalConfigAuthFailAction	OBJECT-TYPE
+	SYNTAX							INTEGER { blockTraffic(1),
+                  									restrictedVlan(2) }
+	MAX-ACCESS						read-write
+	STATUS							current
+	DESCRIPTION						"To Configure the action to take when the authentication fails"
+
+::= {brcdDot1xAuthGlobalConfigGroup 14 }
+
+---802.1x Per Port Statistics Table
+
+brcdDot1xAuthPortStatTable		OBJECT-TYPE
+	SYNTAX			SEQUENCE OF BrcdDot1xAuthPortStatEntry
+	MAX-ACCESS		not-accessible
+	STATUS			current
+	DESCRIPTION		"A table that contains port EAP(Extensible Authentication
+					Protocol) frames statistics for 802.1x authentication"
+	::= { brcdDot1xAuthPortStatistics 1 }
+
+brcdDot1xAuthPortStatEntry		OBJECT-TYPE
+	 SYNTAX			BrcdDot1xAuthPortStatEntry
+	 MAX-ACCESS		not-accessible
+	 STATUS			current
+	 DESCRIPTION	"An entry of EAP frames statistics indexed by ifIndex"
+	 INDEX			{ifIndex  }
+	 ::= { brcdDot1xAuthPortStatTable 1 }
+
+
+BrcdDot1xAuthPortStatEntry  ::= SEQUENCE {
+	brcdDot1xAuthPortStatRxEAPFrames				Counter32,
+	brcdDot1xAuthPortStatTxEAPFrames				Counter32,
+	brcdDot1xAuthPortStatRxEAPStartFrames			Counter32,
+	brcdDot1xAuthPortStatRxEAPLogOffFrames			Counter32,
+	brcdDot1xAuthPortStatRxEAPRespIdFrames			Counter32,
+	brcdDot1xAuthPortStatTxEAPReqIdFrames			Counter32,
+	brcdDot1xAuthPortStatRxEAPInvalidFrames			Counter32,
+	brcdDot1xAuthPortStatEAPLastFrameVersionRx	 	Unsigned32,
+	brcdDot1xAuthPortStatRxEAPRespOrIdFrames		Counter32,
+	brcdDot1xAuthPortStatRxLengthErrorFrame			Integer32,
+	brcdDot1xAuthPortStatTxRequestFrames			Counter32,
+	brcdDot1xAuthPortStatLastEAPFrameSource		MacAddress
+ }
+
+brcdDot1xAuthPortStatRxEAPFrames	OBJECT-TYPE
+	SYNTAX			Counter32
+	MAX-ACCESS		read-only
+	STATUS			current
+	DESCRIPTION		"The total number of EAPOL frames received on the port
+				  	It includes EAP frames - "
+	::= { brcdDot1xAuthPortStatEntry 1 }
+
+brcdDot1xAuthPortStatTxEAPFrames	OBJECT-TYPE
+	SYNTAX			Counter32
+	MAX-ACCESS		read-only
+	STATUS			current
+	DESCRIPTION		"The no of EAPOL frames transmitted on the port"
+	::= { brcdDot1xAuthPortStatEntry 2 }
+
+brcdDot1xAuthPortStatRxEAPStartFrames	OBJECT-TYPE
+	SYNTAX			Counter32
+	MAX-ACCESS		read-only
+	STATUS			current
+	DESCRIPTION		"The number of EAPOL-Start frames received on the port"
+	::= { brcdDot1xAuthPortStatEntry 3 }
+
+brcdDot1xAuthPortStatRxEAPLogOffFrames	OBJECT-TYPE
+	SYNTAX			Counter32
+	MAX-ACCESS		read-only
+	STATUS			current
+	DESCRIPTION		"The number of EAPOL-Logoff frames received on the port"
+	::= { brcdDot1xAuthPortStatEntry 4 }
+
+brcdDot1xAuthPortStatRxEAPRespIdFrames	OBJECT-TYPE
+	SYNTAX			Counter32
+	MAX-ACCESS		read-only
+	STATUS			current
+	DESCRIPTION		"The number of  EAP frames other than Response/Identity
+					frames received on the port"
+	::= { brcdDot1xAuthPortStatEntry 5 }
+
+brcdDot1xAuthPortStatTxEAPReqIdFrames	OBJECT-TYPE
+	SYNTAX			Counter32
+	MAX-ACCESS		read-only
+	STATUS			current
+	DESCRIPTION		"The number of EAP-Request/Identity frames transmitted on
+					the port"
+	::= { brcdDot1xAuthPortStatEntry 6 }
+
+brcdDot1xAuthPortStatRxEAPInvalidFrames	OBJECT-TYPE
+	SYNTAX			Counter32
+	MAX-ACCESS		read-only
+	STATUS			current
+	DESCRIPTION		"The number of invalid EAPOL frames received on the port"
+	::= { brcdDot1xAuthPortStatEntry 7 }
+
+brcdDot1xAuthPortStatEAPLastFrameVersionRx		OBJECT-TYPE
+	SYNTAX			Unsigned32
+	MAX-ACCESS		read-only
+	STATUS			current
+	DESCRIPTION		"The version of last EAP frame received"
+	::= { brcdDot1xAuthPortStatEntry 8 }
+
+brcdDot1xAuthPortStatRxEAPRespOrIdFrames		OBJECT-TYPE
+	SYNTAX			Counter32
+	MAX-ACCESS		read-only
+	STATUS			current
+	DESCRIPTION		"The number of  received EAP response or Id frames on the
+					port"
+	::= { brcdDot1xAuthPortStatEntry 9 }
+
+brcdDot1xAuthPortStatRxLengthErrorFrame		OBJECT-TYPE
+	SYNTAX			Integer32
+	MAX-ACCESS		read-only
+	STATUS			current
+	DESCRIPTION		"The received EAP Length Error frame"
+	::= { brcdDot1xAuthPortStatEntry 10 }
+
+brcdDot1xAuthPortStatTxRequestFrames		OBJECT-TYPE
+	SYNTAX			Counter32
+	MAX-ACCESS		read-only
+	STATUS			current
+	DESCRIPTION		"The number of  transmitted EAP request frames on the port"
+	::= { brcdDot1xAuthPortStatEntry 11 }
+
+brcdDot1xAuthPortStatLastEAPFrameSource OBJECT-TYPE
+	SYNTAX			MacAddress
+	MAX-ACCESS		read-only
+	STATUS			current
+	DESCRIPTION		"The MAC address of the source from which the last EAP frame came"
+        ::= {brcdDot1xAuthPortStatEntry 12}
+
+---A table of 802.1x dynamic states that the port is currently in..
+
+brcdDot1xAuthPortStateTable		OBJECT-TYPE
+	SYNTAX			SEQUENCE OF BrcdDot1xAuthPortStateEntry
+	MAX-ACCESS		not-accessible
+	STATUS			current
+	DESCRIPTION		"A table that contains entries of port dot1x values"
+	::= { brcdDot1xAuthPortState 1 }
+
+brcdDot1xAuthPortStateEntry 			OBJECT-TYPE
+	SYNTAX			BrcdDot1xAuthPortStateEntry
+	MAX-ACCESS		not-accessible
+	STATUS			current
+	DESCRIPTION		"An entry of 802.1x config values indexed by ifIndex to
+					be able to have port values"
+		INDEX		{ ifIndex }
+	::= { brcdDot1xAuthPortStateTable 1 }
+
+BrcdDot1xAuthPortStateEntry ::= SEQUENCE {
+	brcdDot1xAuthPortStateMacSessions			Unsigned32,
+	brcdDot1xAuthPortStateAuthMacSessions		Unsigned32,
+	brcdDot1xAuthPortStateOriginalPVID			Unsigned32,
+	brcdDot1xAuthPortStatePVIDMacTotal			Unsigned32,
+	brcdDot1xAuthPortStatePVIDMacAuthorized		Unsigned32,
+	brcdDot1xAuthPortStatePortVlanState			INTEGER,
+	brcdDot1xAuthPortStatePVID					Unsigned32,
+	brcdDot1xAuthPortStateRestrictPVID			Unsigned32,
+	brcdDot1xAuthPortStateRadiusAssignPVID		Unsigned32
+	}
+
+brcdDot1xAuthPortStateMacSessions	OBJECT-TYPE
+	SYNTAX			Unsigned32
+	MAX-ACCESS		read-only
+	STATUS			current
+	DESCRIPTION		"Number of 802.1x MAC sessions per port"
+	::= { brcdDot1xAuthPortStateEntry 1 }
+
+brcdDot1xAuthPortStateAuthMacSessions	OBJECT-TYPE
+	SYNTAX			Unsigned32
+	MAX-ACCESS		read-only
+	STATUS			current
+	DESCRIPTION		"Number of Authorized MAC sessions per port"
+	::= { brcdDot1xAuthPortStateEntry 2 }
+
+brcdDot1xAuthPortStateOriginalPVID	OBJECT-TYPE
+	SYNTAX			Unsigned32
+	MAX-ACCESS		read-only
+	STATUS			current
+	DESCRIPTION		"Originally configured(not dynamically assigned)
+					PVID(port's default VLAN ID) for the port"
+	::= { brcdDot1xAuthPortStateEntry 3}
+
+brcdDot1xAuthPortStatePVIDMacTotal	OBJECT-TYPE
+	SYNTAX			Unsigned32
+	MAX-ACCESS		read-only
+	STATUS			current
+	DESCRIPTION		"The number of devices transmitting untagged traffic
+					 on the port's PVID"
+	::= { brcdDot1xAuthPortStateEntry 4 }
+
+brcdDot1xAuthPortStatePVIDMacAuthorized 	OBJECT-TYPE
+	SYNTAX			Unsigned32
+	MAX-ACCESS		read-only
+	STATUS			current
+	DESCRIPTION		"The number of devices transmitting untagged traffic
+					on the port's PVID as a result of dynamic VLAN assignment"
+	::= { brcdDot1xAuthPortStateEntry 5 }
+
+brcdDot1xAuthPortStatePortVlanState	 OBJECT-TYPE
+	SYNTAX			INTEGER { radius(1), restricted(2), normal(3) }
+	MAX-ACCESS		read-only
+	STATUS			current
+	DESCRIPTION		"The Current Vlan state the port is in, which can be
+					RADIUS -The port's PVID was dynamically assigned by a RADIUS server
+					Restricted - The port's PVID is the restricted VLAN Normal - The port's PVID is not set by a RADIUS server,
+					nor is it the restricted VLAN"
+	::= { brcdDot1xAuthPortStateEntry 6 }
+
+brcdDot1xAuthPortStatePVID		OBJECT-TYPE
+	SYNTAX			Unsigned32
+	MAX-ACCESS		read-only
+	STATUS			current
+	DESCRIPTION		"The Dot1x Authentication default Port VLAN Id"
+	::= { brcdDot1xAuthPortStateEntry 7 }
+
+brcdDot1xAuthPortStateRestrictPVID	OBJECT-TYPE
+	SYNTAX			Unsigned32
+	MAX-ACCESS		read-only
+	STATUS			current
+	DESCRIPTION		"Restrict  PVID"
+	::= { brcdDot1xAuthPortStateEntry 8 }
+
+brcdDot1xAuthPortStateRadiusAssignPVID		OBJECT-TYPE
+	SYNTAX			Unsigned32
+	MAX-ACCESS		read-only
+	STATUS			current
+	DESCRIPTION		"RADIUS assign PVID"
+	::= { brcdDot1xAuthPortStateEntry 9 }
+
+--- A table of port configuration parameters for 802.1x authentication
+
+brcdDot1xAuthPortConfigTable		OBJECT-TYPE
+	SYNTAX			SEQUENCE OF BrcdDot1xAuthPortConfigEntry
+	MAX-ACCESS		not-accessible
+	STATUS			current
+	DESCRIPTION		"A table that allows configuration of dot1x values for a given port"
+	::= { brcdDot1xAuthPortConfig  1 }
+
+brcdDot1xAuthPortConfigEntry 			OBJECT-TYPE
+	SYNTAX			BrcdDot1xAuthPortConfigEntry
+	MAX-ACCESS		not-accessible
+	STATUS			current
+	DESCRIPTION		"An entry of 802.1x config values"
+	INDEX		{ ifIndex }
+	::= { brcdDot1xAuthPortConfigTable 1 }
+
+BrcdDot1xAuthPortConfigEntry ::= SEQUENCE {
+	brcdDot1xAuthPortConfigPortControl			INTEGER,
+	brcdDot1xAuthPortConfigFilterStrictSec		EnabledStatus,
+	brcdDot1xAuthPortConfigDot1xOnPort			EnabledStatus
+	}
+
+brcdDot1xAuthPortConfigPortControl		OBJECT-TYPE
+	SYNTAX			INTEGER	{ forceUnauthorized(1), controlauto(2), forceAuthorized(3)}
+	MAX-ACCESS		read-write
+	STATUS			current
+	DESCRIPTION		"The configured port control type
+					for the interface which can be
+					1. force-unauthorized - port's controlled port is placed
+					unconditionally in the unauthorized state
+					2. control-auto - the controlled port is unauthorized
+					until authentication takes place between client and RADIUS
+					3. force-authorized - the port's controlled port is placed
+					unconditionally in the authorized state"
+
+			::= { brcdDot1xAuthPortConfigEntry 1 }
+
+brcdDot1xAuthPortConfigFilterStrictSec	OBJECT-TYPE
+	SYNTAX			EnabledStatus
+	MAX-ACCESS 	read-write
+	STATUS			current
+	DESCRIPTION		"To configure  filter strict security
+					on the interface - enable(1) or disable(0)"
+	::= { brcdDot1xAuthPortConfigEntry 2 }
+
+brcdDot1xAuthPortConfigDot1xOnPort			OBJECT-TYPE
+	SYNTAX			EnabledStatus
+	MAX-ACCESS 	read-write
+	STATUS			current
+	DESCRIPTION		"To Configure (enable / disable) 802.1x  on an interface level"
+	::= { brcdDot1xAuthPortConfigEntry 3 }
+
+---A table that contains 802.1x mac-sessions
+
+brcdDot1xAuthMacSessionTable	OBJECT-TYPE
+	SYNTAX			SEQUENCE OF BrcdDot1xAuthMacSessionEntry
+	MAX-ACCESS		not-accessible
+	STATUS			current
+	DESCRIPTION		"A table that contains 802.1x MAC sessions"
+	::= { brcdDot1xAuthMacSession 1}
+
+brcdDot1xAuthMacSessionEntry  	OBJECT-TYPE
+	SYNTAX			BrcdDot1xAuthMacSessionEntry
+	MAX-ACCESS		not-accessible
+	STATUS			current
+	DESCRIPTION		"An entry containing information applicable to
+					a particular interface and client MAC ie., dot1x-mac-session "
+	INDEX			 { ifIndex, brcdDot1xAuthMacSessionAuthMac }
+	::= { brcdDot1xAuthMacSessionTable 1 }
+
+BrcdDot1xAuthMacSessionEntry ::=
+	SEQUENCE {
+	brcdDot1xAuthMacSessionAuthMac		MacAddress,
+	brcdDot1xAuthMacSessionUserName		SnmpAdminString,
+	brcdDot1xAuthMacSessionIncomingVlanId	VlanId,
+	brcdDot1xAuthMacSessionCurrentVlanId	VlanId,
+	brcdDot1xAuthMacSessionAccessStatus	INTEGER,
+	brcdDot1xAuthMacSessionMaxAge		Unsigned32,
+	brcdDot1xAuthMacSessionAddrType		InetAddressType,
+	brcdDot1xAuthMacSessionIpAddr			InetAddress,
+	brcdDot1xAuthMacSessionAging			INTEGER
+	}
+
+brcdDot1xAuthMacSessionAuthMac	OBJECT-TYPE
+	SYNTAX			MacAddress
+	MAX-ACCESS		not-accessible
+	STATUS			current
+	DESCRIPTION		"Mac address of the client - which
+					basically represents the username used for RADIUS authentication"
+	::= { brcdDot1xAuthMacSessionEntry 1 }
+
+brcdDot1xAuthMacSessionUserName		OBJECT-TYPE
+	SYNTAX			SnmpAdminString
+	MAX-ACCESS		read-only
+	STATUS			current
+	DESCRIPTION		"User name of the 802.1x mac session"
+	::= { brcdDot1xAuthMacSessionEntry 2 }
+
+brcdDot1xAuthMacSessionIncomingVlanId                  OBJECT-TYPE
+	SYNTAX				VlanId
+	MAX-ACCESS			read-only
+	STATUS				current
+	DESCRIPTION			"Incoming VLAN ID"
+	::= { brcdDot1xAuthMacSessionEntry 3 }
+
+brcdDot1xAuthMacSessionCurrentVlanId 	OBJECT-TYPE
+	SYNTAX			VlanId
+	MAX-ACCESS		read-only
+	STATUS			current
+	DESCRIPTION		"The VLAN to which the port is currently assigned"
+	::= { brcdDot1xAuthMacSessionEntry 4 }
+
+brcdDot1xAuthMacSessionAccessStatus 	OBJECT-TYPE
+	SYNTAX			INTEGER { permit(1), blocked(2), restrict(3), init(4) }
+	MAX-ACCESS		read-only
+	STATUS			current
+	DESCRIPTION		"The authentication state of the dot1x-mac-session - which
+					can be permitted, denied, restricted or in the Init state"
+	::= { brcdDot1xAuthMacSessionEntry 5 }
+
+brcdDot1xAuthMacSessionMaxAge	OBJECT-TYPE
+	SYNTAX			Unsigned32
+	MAX-ACCESS		read-only
+	STATUS			current
+	DESCRIPTION		"MAX Age of the mac session in which
+					  the MAC address is authenticated."
+	::= { brcdDot1xAuthMacSessionEntry 6 }
+
+brcdDot1xAuthMacSessionAddrType	 OBJECT-TYPE
+	SYNTAX			InetAddressType
+	MAX-ACCESS		read-only
+	STATUS			current
+	DESCRIPTION		"Client(supplicant) IP address Type. Supported address types
+					are ipv4(1) and ipv6(2)"
+	DEFVAL	{ ipv4 }
+	::= { brcdDot1xAuthMacSessionEntry 7 }
+
+brcdDot1xAuthMacSessionIpAddr			OBJECT-TYPE
+	SYNTAX			InetAddress
+	MAX-ACCESS		read-only
+	STATUS			current
+	DESCRIPTION		"The IP Address of the client"
+	::= { brcdDot1xAuthMacSessionEntry 8 }
+
+brcdDot1xAuthMacSessionAging		OBJECT-TYPE
+	SYNTAX			INTEGER { software(1), hardware(2), ena(3), notapplicable(4) }
+	MAX-ACCESS		read-only
+	STATUS			current
+	DESCRIPTION		"The age's type - Hardware
+					 or Software aging, Ena in which case
+					 the aging hasn't started, or notapplicable when
+					 there is a fake 802.1x mac session"
+	::= { brcdDot1xAuthMacSessionEntry 9 }
+
+---A scalar belonging to brcdDot1xAuthGlobalAdminGroup
+
+brcdDot1xAuthGlobalAdminConfigStatus OBJECT-TYPE
+	SYNTAX			EnabledStatus
+	MAX-ACCESS		read-write
+	STATUS			current
+	DESCRIPTION		"Used to enable /disable 802.1x authentication globally"
+	DEFVAL			{ disabled }
+	::= { brcdDot1xAuthGlobalAdminGroup 1}
+
+END

mibs/BROCADE-SYSLOG-MIB

@@ -0,0 +1,137 @@
+BROCADE-SYSLOG-MIB DEFINITIONS ::= BEGIN
+
+IMPORTS
+    MODULE-IDENTITY, OBJECT-TYPE, Counter32, Unsigned32
+      FROM SNMPv2-SMI                  -- [RFC2578]
+    RowStatus
+      FROM SNMPv2-TC                   -- [RFC2579]
+    InetAddress, InetAddressType
+      FROM INET-ADDRESS-MIB            -- [RFC4001]
+    brcdSysLog
+      FROM FOUNDRY-SN-ROOT-MIB;        -- [snroo101]
+
+brocadeSysLogMIB MODULE-IDENTITY
+    LAST-UPDATED "201111040000Z"  -- Novemeber 4, 2011
+    ORGANIZATION "Brocade Communications Systems, Inc."
+    CONTACT-INFO
+             "Technical Support Center
+              130 Holger Way,
+              San Jose, CA  95134
+              Email:  ipsupport@brocade.com
+              Phone: 1-800-752-8061
+              URL:  www.brocade.com"
+    DESCRIPTION
+             "This MIB module contains the managed object definitions for
+              syslog
+
+              Copyright 1996-2011 Brocade Communications Systems, Inc.
+              All rights reserved.
+              This Brocade Communications Systems SNMP Management Information
+              Base Specification embodies Brocade Communications Systems'
+              confidential and proprietary intellectual property.
+              Brocade Communications Systems retains all title and ownership
+              in the Specification, including any revisions.
+
+              This Specification is supplied AS IS, and Brocade Communications
+              Systems makes no warranty, either express or implied, as to the
+              use, operation, condition, or performance of the specification,
+              and any unintended consequence it may on the user environment."
+
+    REVISION     "201111040000Z"          -- November 04, 2011
+    DESCRIPTION
+            "Initial revision"
+    ::= { brcdSysLog 1 }
+
+
+    --
+    -- Top level components of this MIB.
+    --
+    brcdSysLogGroup OBJECT IDENTIFIER ::= { brocadeSysLogMIB 1 }
+
+    --
+    -- IPv4/IPv6 SysLog Server table
+    --
+    -- snAgSysLogServerTable will be deprecated and will be replaced by
+    -- brcdSysLogServerTable.
+
+    brcdSysLogServerTable OBJECT-TYPE
+        SYNTAX        SEQUENCE OF BrcdSysLogServerEntry
+        MAX-ACCESS    not-accessible
+        STATUS        current
+        DESCRIPTION
+                "System Log Server table."
+        ::= { brcdSysLogGroup 1 }
+
+    brcdSysLogServerEntry OBJECT-TYPE
+        SYNTAX        BrcdSysLogServerEntry
+        MAX-ACCESS    not-accessible
+        STATUS        current
+        DESCRIPTION
+                "A row in the System Log Server table."
+        INDEX        {
+                brcdSysLogServerAddrType,
+                brcdSysLogServerAddr,
+                brcdSysLogServerUDPPort
+        }
+        ::= { brcdSysLogServerTable 1 }
+
+    BrcdSysLogServerEntry ::= SEQUENCE {
+        brcdSysLogServerAddrType
+                InetAddressType,
+        brcdSysLogServerAddr
+                InetAddress,
+        brcdSysLogServerUDPPort
+                Unsigned32,
+        brcdSysLogServerOutPkts
+                Counter32,
+        brcdSysLogServerRowStatus
+                RowStatus
+        }
+
+    brcdSysLogServerAddrType OBJECT-TYPE
+        SYNTAX      InetAddressType
+        MAX-ACCESS  not-accessible
+        STATUS      current
+        DESCRIPTION
+                "The syslog server address type. The supported address types
+                 are ipv4(1) and ipv6(2)."
+        ::= { brcdSysLogServerEntry 1 }
+
+    brcdSysLogServerAddr OBJECT-TYPE
+        SYNTAX      InetAddress
+        MAX-ACCESS  not-accessible
+        STATUS      current
+        DESCRIPTION
+                "IP address of syslog server."
+        ::= { brcdSysLogServerEntry 2 }
+
+    brcdSysLogServerUDPPort OBJECT-TYPE
+        SYNTAX      Unsigned32  (1..65535)
+        MAX-ACCESS  not-accessible
+        STATUS      current
+        DESCRIPTION
+                "UDP port number of syslog server."
+        ::= { brcdSysLogServerEntry 3 }
+
+    brcdSysLogServerOutPkts OBJECT-TYPE
+        SYNTAX      Counter32
+        MAX-ACCESS  read-only
+        STATUS      current
+        DESCRIPTION
+                "Number of sylog packets sent to this syslog server."
+        ::= { brcdSysLogServerEntry 4 }
+
+    brcdSysLogServerRowStatus OBJECT-TYPE
+        SYNTAX      RowStatus
+        MAX-ACCESS  read-create
+        STATUS      current
+        DESCRIPTION
+                "Setting this object to createAndGo(4) results in addition
+                 of new row. Setting this object to destroy( 6)results in
+                 removal of a row. The value active(1) is returned for
+                 get and get-next requests.
+                 Other values in the enumeration are not used."
+        ::= { brcdSysLogServerEntry 5 }
+
+END
+

mibs/DVMRP-STD-MIB

@@ -0,0 +1,751 @@
+DVMRP-STD-MIB DEFINITIONS ::= BEGIN
+
+IMPORTS
+    MODULE-IDENTITY, OBJECT-TYPE, experimental,
+    Integer32, Counter32, Gauge32, NOTIFICATION-TYPE,
+    IpAddress, TimeTicks             FROM SNMPv2-SMI
+    DisplayString, RowStatus         FROM SNMPv2-TC
+    MODULE-COMPLIANCE, OBJECT-GROUP,
+    NOTIFICATION-GROUP               FROM SNMPv2-CONF
+--    SnmpAdminString                  FROM SNMP-FRAMEWORK-MIB
+    InterfaceIndexOrZero,
+    InterfaceIndex                   FROM IF-MIB;
+
+dvmrpStdMIB MODULE-IDENTITY
+    LAST-UPDATED "200111211200Z"
+    ORGANIZATION "IETF IDMR Working Group."
+    CONTACT-INFO
+            " Dave Thaler
+              Microsoft
+              One Microsoft Way
+              Redmond, WA 98052-6399
+              EMail: dthaler@microsoft.com"
+    DESCRIPTION
+            "The MIB module for management of DVMRP routers."
+    REVISION     "200111211200Z"
+    DESCRIPTION
+            "Initial version, published as RFC xxxx (to be filled in by
+            RFC-Editor)."
+    ::= { experimental 62 }
+    -- NOTE TO RFC EDITOR: When this document is published as an
+    -- RFC, replace xx with IANA assignment, and delete this comment.
+    -- Also, the following statement should be restored.
+
+dvmrpMIBObjects OBJECT IDENTIFIER ::= { dvmrpStdMIB 1 }
+
+dvmrp           OBJECT IDENTIFIER ::= { dvmrpMIBObjects 1 }
+
+dvmrpScalar     OBJECT IDENTIFIER ::= { dvmrp 1 }
+
+dvmrpVersionString OBJECT-TYPE
+    SYNTAX     DisplayString
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+            "The router's DVMRP version information.  Similar to
+            sysDescr in MIB-II, this is a free-form field which can be
+            used to display vendor-specific information."
+    ::= { dvmrpScalar 1 }
+
+-- dvmrpScalar 2 was previously used for a global
+-- Generation ID.  However, the DVMRP spec changed it to
+-- a per-interface parameter.
+dvmrpNumRoutes OBJECT-TYPE
+    SYNTAX     Gauge32
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+            "The number of entries in the routing table.  This can be
+            used to monitor the routing table size."
+    ::= { dvmrpScalar 3 }
+
+dvmrpReachableRoutes OBJECT-TYPE
+    SYNTAX     Gauge32
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+            "The number of entries in the routing table with non
+            infinite metrics.  This can be used to detect network
+            partitions by observing the ratio of reachable routes to
+            total routes."
+    ::= { dvmrpScalar 4 }
+
+-- The DVMRP Interface Table
+
+dvmrpInterfaceTable OBJECT-TYPE
+    SYNTAX     SEQUENCE OF DvmrpInterfaceEntry
+    MAX-ACCESS not-accessible
+    STATUS     current
+    DESCRIPTION
+            "The (conceptual) table listing the router's multicast-
+            capable interfaces."
+    ::= { dvmrp 2 }
+
+dvmrpInterfaceEntry OBJECT-TYPE
+    SYNTAX     DvmrpInterfaceEntry
+    MAX-ACCESS not-accessible
+    STATUS     current
+    DESCRIPTION
+            "An entry (conceptual row) in the dvmrpInterfaceTable.  This
+            row augments ipMRouteInterfaceEntry in the IP Multicast MIB,
+            where the threshold object resides."
+    INDEX      { dvmrpInterfaceIndex }
+    ::= { dvmrpInterfaceTable 1 }
+
+DvmrpInterfaceEntry ::= SEQUENCE {
+    dvmrpInterfaceIndex                 InterfaceIndex,
+    dvmrpInterfaceLocalAddress          IpAddress,
+    dvmrpInterfaceMetric                Integer32,
+    dvmrpInterfaceStatus                RowStatus,
+    dvmrpInterfaceRcvBadPkts            Counter32,
+    dvmrpInterfaceRcvBadRoutes          Counter32,
+    dvmrpInterfaceSentRoutes            Counter32,
+--    dvmrpInterfaceKey                   SnmpAdminString,
+    dvmrpInterfaceKey                   DisplayString,
+    dvmrpInterfaceKeyVersion            Integer32,
+    dvmrpInterfaceGenerationId          Integer32
+}
+
+dvmrpInterfaceIndex OBJECT-TYPE
+    SYNTAX     InterfaceIndex
+    MAX-ACCESS not-accessible
+    STATUS     current
+    DESCRIPTION
+            "The ifIndex value of the interface for which DVMRP is
+            enabled."
+    ::= { dvmrpInterfaceEntry 1 }
+
+dvmrpInterfaceLocalAddress OBJECT-TYPE
+    SYNTAX     IpAddress
+    MAX-ACCESS read-create
+    STATUS     current
+    DESCRIPTION
+            "The IP address this system will use as a source address on
+            this interface.  On unnumbered interfaces, it must be the
+            same value as dvmrpInterfaceLocalAddress for some interface
+            on the system."
+    ::= { dvmrpInterfaceEntry 2 }
+
+dvmrpInterfaceMetric OBJECT-TYPE
+    SYNTAX     Integer32 (1..31)
+    MAX-ACCESS read-create
+    STATUS     current
+    DESCRIPTION
+            "The distance metric for this interface which is used to
+            calculate distance vectors."
+    DEFVAL     { 1 }
+    ::= { dvmrpInterfaceEntry 3 }
+
+dvmrpInterfaceStatus OBJECT-TYPE
+    SYNTAX     RowStatus
+    MAX-ACCESS read-create
+    STATUS     current
+    DESCRIPTION
+            "The status of this entry.  Creating the entry enables DVMRP
+            on the virtual interface; destroying the entry or setting it
+            to notInService disables DVMRP on the virtual interface."
+    ::= { dvmrpInterfaceEntry 4 }
+
+dvmrpInterfaceRcvBadPkts OBJECT-TYPE
+    SYNTAX     Counter32
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+            "The number of DVMRP messages received on the interface by
+            the DVMRP process which were subsequently discarded as
+            invalid (e.g. invalid packet format, or a route report from
+            an unknown neighbor)."
+    ::= { dvmrpInterfaceEntry 5 }
+
+dvmrpInterfaceRcvBadRoutes OBJECT-TYPE
+    SYNTAX     Counter32
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+            "The number of routes, in valid DVMRP packets, which were
+            ignored because the entry was invalid."
+    ::= { dvmrpInterfaceEntry 6 }
+
+dvmrpInterfaceSentRoutes OBJECT-TYPE
+    SYNTAX     Counter32
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+            "The number of routes, in DVMRP Report packets, which have
+            been sent on this interface.  Together with
+            dvmrpNeighborRcvRoutes at a peer, this object is useful for
+            detecting routes being lost."
+    ::= { dvmrpInterfaceEntry 7 }
+
+dvmrpInterfaceKey OBJECT-TYPE
+--    SYNTAX     SnmpAdminString
+    SYNTAX     DisplayString
+    MAX-ACCESS read-create
+    STATUS     current
+    DESCRIPTION
+            "The (shared) key for authenticating neighbors on this
+            interface.  This object is intended solely for the purpose
+            of setting the interface key, and MUST be accessible only
+            via requests using both authentication and privacy.  The
+            agent MAY report an empty string in response to get, get-
+            next, get-bulk requests."
+    ::= { dvmrpInterfaceEntry 8 }
+
+dvmrpInterfaceKeyVersion OBJECT-TYPE
+    SYNTAX     Integer32
+    MAX-ACCESS read-create
+    STATUS     current
+    DESCRIPTION
+            "The highest version number of all known interface keys for
+            this interface used for authenticating neighbors."
+    ::= { dvmrpInterfaceEntry 9 }
+
+dvmrpInterfaceGenerationId OBJECT-TYPE
+    SYNTAX     Integer32
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+            "The generation identifier for the interface.  This is used
+            by neighboring routers to detect whether the DVMRP routing
+            table should be resent."
+    ::= { dvmrpInterfaceEntry 10 }
+
+-- The DVMRP Neighbor Table
+
+dvmrpNeighborTable OBJECT-TYPE
+    SYNTAX     SEQUENCE OF DvmrpNeighborEntry
+    MAX-ACCESS not-accessible
+    STATUS     current
+    DESCRIPTION
+            "The (conceptual) table listing the router's DVMRP
+            neighbors, as discovered by receiving DVMRP messages."
+    ::= { dvmrp 3 }
+
+dvmrpNeighborEntry OBJECT-TYPE
+    SYNTAX     DvmrpNeighborEntry
+    MAX-ACCESS not-accessible
+    STATUS     current
+    DESCRIPTION
+            "An entry (conceptual row) in the dvmrpNeighborTable."
+    INDEX      { dvmrpNeighborIfIndex, dvmrpNeighborAddress }
+    ::= { dvmrpNeighborTable 1 }
+
+DvmrpNeighborEntry ::= SEQUENCE {
+    dvmrpNeighborIfIndex         InterfaceIndex,
+    dvmrpNeighborAddress         IpAddress,
+    dvmrpNeighborUpTime          TimeTicks,
+    dvmrpNeighborExpiryTime      TimeTicks,
+    dvmrpNeighborGenerationId    Integer32,
+    dvmrpNeighborMajorVersion    Integer32,
+    dvmrpNeighborMinorVersion    Integer32,
+    dvmrpNeighborCapabilities    BITS,
+    dvmrpNeighborRcvRoutes       Counter32,
+    dvmrpNeighborRcvBadPkts      Counter32,
+    dvmrpNeighborRcvBadRoutes    Counter32,
+    dvmrpNeighborState           INTEGER
+}
+
+dvmrpNeighborIfIndex OBJECT-TYPE
+    SYNTAX     InterfaceIndex
+    MAX-ACCESS not-accessible
+    STATUS     current
+    DESCRIPTION
+            "The value of ifIndex for the virtual interface used to
+            reach this DVMRP neighbor."
+    ::= { dvmrpNeighborEntry 1 }
+
+dvmrpNeighborAddress OBJECT-TYPE
+    SYNTAX     IpAddress
+    MAX-ACCESS not-accessible
+    STATUS     current
+    DESCRIPTION
+            "The IP address of the DVMRP neighbor for which this entry
+            contains information."
+    ::= { dvmrpNeighborEntry 2 }
+
+dvmrpNeighborUpTime OBJECT-TYPE
+    SYNTAX     TimeTicks
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+            "The time since this DVMRP neighbor (last) became a neighbor
+            of the local router."
+    ::= { dvmrpNeighborEntry 3 }
+
+dvmrpNeighborExpiryTime OBJECT-TYPE
+    SYNTAX     TimeTicks
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+            "The minimum time remaining before this DVMRP neighbor will
+            be aged out."
+    ::= { dvmrpNeighborEntry 4 }
+
+dvmrpNeighborGenerationId OBJECT-TYPE
+    SYNTAX     Integer32
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+            "The neighboring router's generation identifier."
+    ::= { dvmrpNeighborEntry 5 }
+
+dvmrpNeighborMajorVersion OBJECT-TYPE
+    SYNTAX     Integer32 (0..255)
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+            "The neighboring router's major DVMRP version number."
+    ::= { dvmrpNeighborEntry 6 }
+
+dvmrpNeighborMinorVersion OBJECT-TYPE
+    SYNTAX     Integer32 (0..255)
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+            "The neighboring router's minor DVMRP version number."
+    ::= { dvmrpNeighborEntry 7 }
+
+dvmrpNeighborCapabilities OBJECT-TYPE
+    SYNTAX     BITS {
+                   leaf(0),
+                   prune(1),
+                   generationID(2),
+                   mtrace(3)
+               }
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+            "This object describes the neighboring router's
+            capabilities.  The leaf bit indicates that the neighbor has
+            only one interface with neighbors.  The prune bit indicates
+            that the neighbor supports pruning.  The generationID bit
+            indicates that the neighbor sends its generationID in Probe
+            messages.  The mtrace bit indicates that the neighbor can
+            handle mtrace requests."
+    ::= { dvmrpNeighborEntry 8 }
+
+dvmrpNeighborRcvRoutes OBJECT-TYPE
+    SYNTAX     Counter32
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+            "The total number of routes received in valid DVMRP packets
+            received from this neighbor.  This can be used to diagnose
+            problems such as unicast route injection, as well as giving
+            an indication of the level of DVMRP route exchange
+            activity."
+    ::= { dvmrpNeighborEntry 9 }
+
+dvmrpNeighborRcvBadPkts OBJECT-TYPE
+    SYNTAX     Counter32
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+            "The number of packet received from this neighbor which were
+            discarded as invalid."
+    ::= { dvmrpNeighborEntry 10 }
+
+dvmrpNeighborRcvBadRoutes OBJECT-TYPE
+    SYNTAX     Counter32
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+            "The number of routes, in valid DVMRP packets received from
+            this neighbor, which were ignored because the entry was
+            invalid."
+    ::= { dvmrpNeighborEntry 11 }
+
+dvmrpNeighborState OBJECT-TYPE
+    SYNTAX     INTEGER { oneway(1), active(2), ignoring(3), down(4) }
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+            "State of the neighbor adjacency."
+    ::= { dvmrpNeighborEntry 12 }
+
+
+-- The DVMRP Route Table
+
+dvmrpRouteTable OBJECT-TYPE
+    SYNTAX     SEQUENCE OF DvmrpRouteEntry
+    MAX-ACCESS not-accessible
+    STATUS     current
+    DESCRIPTION
+            "The table of routes learned through DVMRP route exchange."
+    ::= { dvmrp 4 }
+
+dvmrpRouteEntry OBJECT-TYPE
+    SYNTAX     DvmrpRouteEntry
+    MAX-ACCESS not-accessible
+    STATUS     current
+    DESCRIPTION
+            "An entry (conceptual row) containing the multicast routing
+            information used by DVMRP in place of the unicast routing
+            information."
+    INDEX      { dvmrpRouteSource, dvmrpRouteSourceMask }
+    ::= { dvmrpRouteTable 1 }
+
+DvmrpRouteEntry ::= SEQUENCE {
+    dvmrpRouteSource             IpAddress,
+    dvmrpRouteSourceMask         IpAddress,
+    dvmrpRouteUpstreamNeighbor   IpAddress,
+    dvmrpRouteIfIndex            InterfaceIndexOrZero,
+    dvmrpRouteMetric             Integer32,
+    dvmrpRouteExpiryTime         TimeTicks,
+    dvmrpRouteUpTime             TimeTicks
+}
+
+dvmrpRouteSource OBJECT-TYPE
+    SYNTAX     IpAddress
+    MAX-ACCESS not-accessible
+    STATUS     current
+    DESCRIPTION
+            "The network address which when combined with the
+            corresponding value of dvmrpRouteSourceMask identifies the
+            sources for which this entry contains multicast routing
+            information."
+    ::= { dvmrpRouteEntry 1 }
+
+dvmrpRouteSourceMask OBJECT-TYPE
+    SYNTAX     IpAddress
+    MAX-ACCESS not-accessible
+    STATUS     current
+    DESCRIPTION
+            "The network mask which when combined with the corresponding
+            value of dvmrpRouteSource identifies the sources for which
+            this entry contains multicast routing information."
+    ::= { dvmrpRouteEntry 2 }
+
+dvmrpRouteUpstreamNeighbor OBJECT-TYPE
+    SYNTAX     IpAddress
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+            "The address of the upstream neighbor (e.g., RPF neighbor)
+            from which IP datagrams from these sources are received."
+    ::= { dvmrpRouteEntry 3 }
+
+dvmrpRouteIfIndex OBJECT-TYPE
+    SYNTAX     InterfaceIndexOrZero
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+            "The value of ifIndex for the interface on which IP
+            datagrams sent by these sources are received.  A value of 0
+            typically means the route is an aggregate for which no next-
+            hop interface exists."
+    ::= { dvmrpRouteEntry 4 }
+
+dvmrpRouteMetric OBJECT-TYPE
+    SYNTAX     Integer32 (1..32)
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+            "The distance in hops to the source subnet."
+    ::= { dvmrpRouteEntry 5 }
+
+dvmrpRouteExpiryTime OBJECT-TYPE
+    SYNTAX     TimeTicks
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+            "The minimum amount of time remaining before this entry will
+            be aged out."
+    ::= { dvmrpRouteEntry 6 }
+
+dvmrpRouteUpTime OBJECT-TYPE
+    SYNTAX     TimeTicks
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+            "The time since the route represented by this entry was
+            learned by the router."
+    ::= { dvmrpRouteEntry 7 }
+
+-- The DVMRP Routing Next Hop Table
+
+dvmrpRouteNextHopTable OBJECT-TYPE
+    SYNTAX     SEQUENCE OF DvmrpRouteNextHopEntry
+    MAX-ACCESS not-accessible
+    STATUS     current
+    DESCRIPTION
+            "The (conceptual) table containing information on the next
+            hops on outgoing interfaces for routing IP multicast
+            datagrams."
+    ::= { dvmrp 5 }
+
+dvmrpRouteNextHopEntry OBJECT-TYPE
+    SYNTAX     DvmrpRouteNextHopEntry
+    MAX-ACCESS not-accessible
+    STATUS     current
+    DESCRIPTION
+            "An entry (conceptual row) in the list of next hops on
+            outgoing interfaces to which IP multicast datagrams from
+            particular sources are routed."
+    INDEX      { dvmrpRouteNextHopSource, dvmrpRouteNextHopSourceMask,
+                 dvmrpRouteNextHopIfIndex }
+    ::= { dvmrpRouteNextHopTable 1 }
+
+DvmrpRouteNextHopEntry ::= SEQUENCE {
+    dvmrpRouteNextHopSource             IpAddress,
+    dvmrpRouteNextHopSourceMask         IpAddress,
+    dvmrpRouteNextHopIfIndex            InterfaceIndex,
+    dvmrpRouteNextHopType               INTEGER
+}
+
+dvmrpRouteNextHopSource OBJECT-TYPE
+    SYNTAX     IpAddress
+    MAX-ACCESS not-accessible
+    STATUS     current
+    DESCRIPTION
+            "The network address which when combined with the
+            corresponding value of dvmrpRouteNextHopSourceMask
+            identifies the sources for which this entry specifies a next
+            hop on an outgoing interface."
+    ::= { dvmrpRouteNextHopEntry 1 }
+
+dvmrpRouteNextHopSourceMask OBJECT-TYPE
+    SYNTAX     IpAddress
+    MAX-ACCESS not-accessible
+    STATUS     current
+    DESCRIPTION
+            "The network mask which when combined with the corresponding
+            value of dvmrpRouteNextHopSource identifies the sources for
+            which this entry specifies a next hop on an outgoing
+            interface."
+    ::= { dvmrpRouteNextHopEntry 2 }
+
+dvmrpRouteNextHopIfIndex OBJECT-TYPE
+    SYNTAX     InterfaceIndex
+    MAX-ACCESS not-accessible
+    STATUS     current
+    DESCRIPTION
+            "The ifIndex value of the interface for the outgoing
+            interface for this next hop."
+    ::= { dvmrpRouteNextHopEntry 3 }
+
+dvmrpRouteNextHopType OBJECT-TYPE
+    SYNTAX     INTEGER { leaf(1), branch(2) }
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+            "Type is leaf if no downstream dependent neighbors exist on
+            the outgoing virtual interface.  Otherwise, type is branch."
+    ::= { dvmrpRouteNextHopEntry 4 }
+
+-- The DVMRP Prune Table
+
+dvmrpPruneTable OBJECT-TYPE
+    SYNTAX     SEQUENCE OF DvmrpPruneEntry
+    MAX-ACCESS not-accessible
+    STATUS     current
+    DESCRIPTION
+            "The (conceptual) table listing the router's upstream prune
+            state."
+    ::= { dvmrp 6 }
+
+dvmrpPruneEntry OBJECT-TYPE
+    SYNTAX     DvmrpPruneEntry
+    MAX-ACCESS not-accessible
+    STATUS     current
+    DESCRIPTION
+            "An entry (conceptual row) in the dvmrpPruneTable."
+    INDEX      { dvmrpPruneGroup, dvmrpPruneSource,
+                 dvmrpPruneSourceMask }
+    ::= { dvmrpPruneTable 1 }
+
+DvmrpPruneEntry ::= SEQUENCE {
+    dvmrpPruneGroup              IpAddress,
+    dvmrpPruneSource             IpAddress,
+    dvmrpPruneSourceMask         IpAddress,
+    dvmrpPruneExpiryTime         TimeTicks
+}
+
+dvmrpPruneGroup OBJECT-TYPE
+    SYNTAX     IpAddress
+    MAX-ACCESS not-accessible
+    STATUS     current
+    DESCRIPTION
+            "The group address which has been pruned."
+    ::= { dvmrpPruneEntry 1 }
+
+dvmrpPruneSource OBJECT-TYPE
+    SYNTAX     IpAddress
+    MAX-ACCESS not-accessible
+    STATUS     current
+    DESCRIPTION
+            "The address of the source or source network which has been
+            pruned."
+    ::= { dvmrpPruneEntry 2 }
+
+dvmrpPruneSourceMask OBJECT-TYPE
+    SYNTAX     IpAddress
+    MAX-ACCESS not-accessible
+    STATUS     current
+    DESCRIPTION
+            "The address of the source or source network which has been
+            pruned.  The mask must either be all 1's, or else
+            dvmrpPruneSource and dvmrpPruneSourceMask must match
+            dvmrpRouteSource and dvmrpRouteSourceMask for some entry in
+            the dvmrpRouteTable."
+    ::= { dvmrpPruneEntry 3 }
+
+dvmrpPruneExpiryTime OBJECT-TYPE
+    SYNTAX     TimeTicks
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+            "The amount of time remaining before this prune should
+            expire at the upstream neighbor.  This value should be the
+            minimum of the default prune lifetime and the remaining
+            prune lifetimes of the local router's downstream neighbors,
+            if any."
+    ::= { dvmrpPruneEntry 4 }
+
+-- DVMRP Traps
+
+dvmrpTraps      OBJECT IDENTIFIER ::= { dvmrp 7 }
+
+dvmrpNeighborLoss NOTIFICATION-TYPE
+    OBJECTS {
+       dvmrpInterfaceLocalAddress, -- The originator of the trap
+       dvmrpNeighborState  -- The new state
+    }
+    STATUS             current
+    DESCRIPTION
+            "A dvmrpNeighborLoss trap signifies the loss of a 2-way
+            adjacency with a neighbor.  This trap should be generated
+            when the neighbor state changes from active to one-way,
+            ignoring, or down.  The trap should be generated only if the
+            router has no other neighbors on the same interface with a
+            lower IP address than itself."
+    --#ENABLE FALSE
+    ::= { dvmrpTraps 1 }
+
+dvmrpNeighborNotPruning NOTIFICATION-TYPE
+    OBJECTS {
+       dvmrpInterfaceLocalAddress, -- The originator of the trap
+       dvmrpNeighborCapabilities
+    }
+    STATUS             current
+    DESCRIPTION
+            "A dvmrpNeighborNotPruning trap signifies that a non-pruning
+            neighbor has been detected (in an implementation-dependent
+            manner).  This trap should be generated at most once per
+            generation ID of the neighbor.  For example, it should be
+            generated at the time a neighbor is first heard from if the
+            prune bit is not set in its capabilities.  It should also be
+            generated if the local system has the ability to tell that a
+            neighbor which sets the the prune bit in its capabilities is
+            not pruning any branches over an extended period of time.
+            The trap should be generated only if the router has no other
+            neighbors on the same interface with a lower IP address than
+            itself."
+    --#ENABLE FALSE
+    ::= { dvmrpTraps 2 }
+
+
+-- conformance information
+
+dvmrpMIBConformance OBJECT IDENTIFIER ::= { dvmrpStdMIB 2 }
+
+dvmrpMIBCompliances OBJECT IDENTIFIER ::= { dvmrpMIBConformance 1 }
+
+dvmrpMIBGroups      OBJECT IDENTIFIER ::= { dvmrpMIBConformance 2 }
+
+
+-- compliance statements
+
+dvmrpMIBCompliance MODULE-COMPLIANCE
+    STATUS  current
+    DESCRIPTION
+            "The compliance statement for the DVMRP MIB."
+    MODULE  -- this module
+        MANDATORY-GROUPS { dvmrpGeneralGroup, dvmrpInterfaceGroup,
+            dvmrpNeighborGroup, dvmrpRoutingGroup, dvmrpTreeGroup
+        }
+
+        GROUP   dvmrpSecurityGroup
+        DESCRIPTION
+            "This group is mandatory for agents which support both
+            authentication and privacy of SNMP messages, and only for
+            those network interfaces for which DVMRP is authenticating
+            neighbors."
+    ::= { dvmrpMIBCompliances 1 }
+
+
+-- units of conformance
+
+dvmrpGeneralGroup OBJECT-GROUP
+    OBJECTS { dvmrpVersionString, dvmrpNumRoutes, dvmrpReachableRoutes
+            }
+    STATUS  current
+    DESCRIPTION
+            "A collection of objects used to describe general DVMRP
+            configuration information."
+    ::= { dvmrpMIBGroups 2 }
+
+dvmrpInterfaceGroup OBJECT-GROUP
+    OBJECTS { dvmrpInterfaceLocalAddress, dvmrpInterfaceMetric,
+              dvmrpInterfaceStatus, dvmrpInterfaceGenerationId,
+              dvmrpInterfaceRcvBadPkts, dvmrpInterfaceRcvBadRoutes,
+              dvmrpInterfaceSentRoutes
+            }
+    STATUS  current
+    DESCRIPTION
+            "A collection of objects used to describe DVMRP interface
+            configuration and statistics."
+    ::= { dvmrpMIBGroups 3 }
+
+dvmrpNeighborGroup OBJECT-GROUP
+    OBJECTS { dvmrpNeighborUpTime, dvmrpNeighborExpiryTime,
+              dvmrpNeighborGenerationId,
+              dvmrpNeighborMajorVersion, dvmrpNeighborMinorVersion,
+              dvmrpNeighborCapabilities, dvmrpNeighborRcvRoutes,
+              dvmrpNeighborRcvBadPkts, dvmrpNeighborRcvBadRoutes,
+              dvmrpNeighborState
+            }
+    STATUS  current
+    DESCRIPTION
+            "A collection of objects used to describe DVMRP peer
+            configuration and statistics."
+    ::= { dvmrpMIBGroups 4 }
+
+dvmrpRoutingGroup OBJECT-GROUP
+    OBJECTS { dvmrpRouteUpstreamNeighbor, dvmrpRouteIfIndex,
+              dvmrpRouteMetric, dvmrpRouteExpiryTime,
+              dvmrpRouteUpTime, dvmrpRouteNextHopType
+            }
+    STATUS  current
+    DESCRIPTION
+            "A collection of objects used to store the DVMRP routing
+            table."
+    ::= { dvmrpMIBGroups 5 }
+
+dvmrpSecurityGroup OBJECT-GROUP
+    OBJECTS { dvmrpInterfaceKey,
+              dvmrpInterfaceKeyVersion }
+    STATUS  current
+    DESCRIPTION
+            "A collection of objects used to store information related
+            to DVMRP security."
+    ::= { dvmrpMIBGroups 6 }
+
+dvmrpTreeGroup OBJECT-GROUP
+    OBJECTS { dvmrpPruneExpiryTime }
+    STATUS  current
+    DESCRIPTION
+            "A collection of objects used to store information related
+            to DVMRP prune state."
+    ::= { dvmrpMIBGroups 7 }
+
+dvmrpNotificationGroup NOTIFICATION-GROUP
+    NOTIFICATIONS { dvmrpNeighborLoss,
+                    dvmrpNeighborNotPruning }
+    STATUS  current
+    DESCRIPTION
+            "A collection of notifications for signaling important DVMRP
+            events."
+    ::= { dvmrpMIBGroups 8 }
+
+END

mibs/FDRY-ACL-MIB

@@ -0,0 +1,321 @@
+FDRY-ACL-MIB DEFINITIONS ::= BEGIN
+
+IMPORTS
+   MODULE-IDENTITY, OBJECT-TYPE,
+					 Unsigned32 	FROM SNMPv2-SMI	   -- [RFC2578]
+   TEXTUAL-CONVENTION, RowStatus,
+   DisplayString, TruthValue		FROM SNMPv2-TC			-- [RFC2579]
+   Ipv6Address						FROM IPV6-TC			-- [RFC2465]
+   fdryAcl							FROM FOUNDRY-SN-ROOT-MIB -- [snroo101]
+   ;
+
+fdryAclMIB MODULE-IDENTITY
+    LAST-UPDATED "201006020000Z"  -- 04 June 2010
+    ORGANIZATION "Brocade Communications Systems, Inc."
+    CONTACT-INFO
+             "Technical Support Center
+              130 Holger Way,
+              San Jose, CA  95134
+              Email:  ipsupport@brocade.com
+              Phone: 1-800-752-8061
+              URL:  www.brocade.com"
+    DESCRIPTION
+		"The Brocade proprietary MIB module for Ipv6 Access Control List.
+		 It has new tables for Ipv6 Access Control List.
+
+              Copyright 1996-2010 Brocade Communications Systems, Inc.
+              All rights reserved.
+              This Brocade Communications Systems SNMP Management Information Base Specification
+              embodies Brocade Communications Systems' confidential and proprietary
+              intellectual property. Brocade Communications Systems retains all
+              title and ownership in the Specification, including any revisions.
+
+              This Specification is supplied AS IS, and Brocade Communications Systems makes
+              no warranty, either express or implied, as to the use,
+              operation, condition, or performance of the specification, and any unintended
+              consequence it may on the user environment."
+
+    REVISION        "201006020000Z"  -- 04 June 2010
+    DESCRIPTION
+        "Changed the ORGANIZATION, CONTACT-INFO and DESCRIPTION fields."
+
+    REVISION	 "200802140000Z"  -- 14 February 2008
+    DESCRIPTION  "Initial version"
+
+   ::= { fdryAcl 1 }
+
+--
+-- Textual Conventions
+--
+RtrStatus ::= TEXTUAL-CONVENTION
+	STATUS	  current
+	DESCRIPTION
+		"Represents a status value such as disabled or enabled."
+	SYNTAX	INTEGER {
+						disabled(0),
+						enabled (1)
+					}
+
+Action ::= TEXTUAL-CONVENTION
+	STATUS	  current
+	DESCRIPTION
+		"Represents a action value such as deny or permit."
+	SYNTAX	INTEGER {
+						deny(0),
+						permit (1)
+					}
+
+Operator ::= TEXTUAL-CONVENTION
+	STATUS	  current
+	DESCRIPTION
+		"Represents a operators value, such as equal, not-equal, lesser than,
+		greater than, range and undefined."
+	SYNTAX	INTEGER {
+						eq(0),
+						neq (1),
+						lt (2),
+						gt (3),
+						range (4),
+						undefined (7)
+					}
+
+IpProtocol ::= TEXTUAL-CONVENTION
+	STATUS	  current
+	DESCRIPTION
+		"Represents a transport protocol value."
+	SYNTAX	Unsigned32 (0..255)
+
+--
+-- Top level components of this MIB.
+--
+
+fdryIpv6Acl		OBJECT IDENTIFIER ::= { fdryAclMIB 1 }
+
+--
+-- Ipv6 Access Control List Table
+--
+fdryIpv6AclTable       OBJECT-TYPE
+	SYNTAX  SEQUENCE OF FdryIpv6AclEntry
+	MAX-ACCESS  not-accessible
+	STATUS  current
+	DESCRIPTION
+		"Table of Ipv6 Access Control List"
+	::= { fdryIpv6Acl 1 }
+
+fdryIpv6AclEntry       OBJECT-TYPE
+	SYNTAX  FdryIpv6AclEntry
+	MAX-ACCESS  not-accessible
+	STATUS  current
+	DESCRIPTION
+		"An entry in the Ipv6 Access Control List table."
+	INDEX   { fdryIpv6AclIndex }
+	::= { fdryIpv6AclTable 1 }
+
+FdryIpv6AclEntry ::= SEQUENCE {
+	fdryIpv6AclIndex
+		Unsigned32,
+	fdryIpv6AclName
+		DisplayString,
+	fdryIpv6AclAction
+		Action,
+	fdryIpv6AclProtocol
+		IpProtocol,
+	fdryIpv6AclSourceIp
+		Ipv6Address,
+	fdryIpv6AclSourcePrefixLen
+		Unsigned32,
+	fdryIpv6AclSourceOperator
+		Operator,
+	fdryIpv6AclSourceOperand1
+		Unsigned32,
+	fdryIpv6AclSourceOperand2
+		Unsigned32,
+	fdryIpv6AclDestinationIp
+		Ipv6Address,
+	fdryIpv6AclDestinationPrefixLen
+		Unsigned32,
+	fdryIpv6AclDestinationOperator
+		Operator,
+	fdryIpv6AclDestinationOperand1
+		Unsigned32,
+	fdryIpv6AclDestinationOperand2
+		Unsigned32,
+	fdryIpv6AclEstablished
+		RtrStatus,
+	fdryIpv6AclLogOption
+		TruthValue,
+	fdryIpv6AclComments
+		DisplayString,
+	fdryIpv6AclRowStatus
+		RowStatus
+	}
+
+fdryIpv6AclIndex       OBJECT-TYPE
+	SYNTAX  Unsigned32
+	MAX-ACCESS  not-accessible
+	STATUS  current
+	DESCRIPTION
+		"The access control list item number for an entry.
+		This is a unique number that identifies different
+		Access list entries. This one has to be
+		unique even though the name is not unique
+		for a give access list with same or different source
+		address, prefix length, destination address and destination
+		prefix length, protocol type, action (permit/deny) type and the
+		operator (neq, eq, gt and , lt)."
+	::= { fdryIpv6AclEntry 1 }
+
+fdryIpv6AclName		OBJECT-TYPE
+	SYNTAX  DisplayString (SIZE (0..199))
+	MAX-ACCESS  read-create
+	STATUS  current
+	DESCRIPTION
+		"Access Control List name for an entry."
+	::= { fdryIpv6AclEntry 2 }
+
+fdryIpv6AclAction      OBJECT-TYPE
+	SYNTAX  Action
+	MAX-ACCESS  read-create
+	STATUS  current
+	DESCRIPTION
+		"Action to take if the ip packet matches
+		with this access control list."
+	::= { fdryIpv6AclEntry 3 }
+
+fdryIpv6AclProtocol    OBJECT-TYPE
+	SYNTAX  IpProtocol
+	MAX-ACCESS  read-create
+	STATUS  current
+	DESCRIPTION
+		"Transport protocols. 0 means any protocol."
+	::= { fdryIpv6AclEntry 4 }
+
+fdryIpv6AclSourceIp    OBJECT-TYPE
+	SYNTAX  Ipv6Address
+	MAX-ACCESS  read-create
+	STATUS  current
+	DESCRIPTION
+		"Source Ipv6 address."
+	::= { fdryIpv6AclEntry 5 }
+
+fdryIpv6AclSourcePrefixLen  OBJECT-TYPE
+	SYNTAX  Unsigned32
+	MAX-ACCESS  read-create
+	STATUS  current
+	DESCRIPTION
+		"Source IPv6 address prefix length."
+    DEFVAL  {64}
+ 	::= { fdryIpv6AclEntry 6 }
+
+fdryIpv6AclSourceOperator    OBJECT-TYPE
+	SYNTAX  Operator
+	MAX-ACCESS  read-create
+	STATUS  current
+	DESCRIPTION
+		"Type of comparison to perform.
+		for now, this only applys to tcp or udp
+		to compare the port number"
+	::= { fdryIpv6AclEntry 7 }
+
+fdryIpv6AclSourceOperand1     OBJECT-TYPE
+	SYNTAX  Unsigned32(0..65535)
+	MAX-ACCESS  read-create
+	STATUS  current
+	DESCRIPTION
+		"For now this only refers to transport
+		protocol port number."
+	::= { fdryIpv6AclEntry 8 }
+
+fdryIpv6AclSourceOperand2     OBJECT-TYPE
+	SYNTAX  Unsigned32(0..65535)
+	MAX-ACCESS  read-create
+	STATUS  current
+	DESCRIPTION
+		"For now this only refers to transport
+		protocol port number."
+	::= { fdryIpv6AclEntry 9 }
+
+fdryIpv6AclDestinationIp      OBJECT-TYPE
+	SYNTAX  Ipv6Address
+	MAX-ACCESS  read-create
+	STATUS  current
+	DESCRIPTION
+		"Destination Ipv6 address."
+	::= { fdryIpv6AclEntry 10 }
+
+fdryIpv6AclDestinationPrefixLen    OBJECT-TYPE
+	SYNTAX  Unsigned32
+	MAX-ACCESS  read-create
+	STATUS  current
+	DESCRIPTION
+		"Destination IPv6 address prefix length."
+
+    DEFVAL  {64}
+ 	::= { fdryIpv6AclEntry 11 }
+
+fdryIpv6AclDestinationOperator    OBJECT-TYPE
+	SYNTAX  Operator
+	MAX-ACCESS  read-create
+	STATUS  current
+	DESCRIPTION
+		"Type of comparison to perform.
+		for now, this only applys to tcp or udp
+		to compare the port number"
+	::= { fdryIpv6AclEntry 12 }
+
+fdryIpv6AclDestinationOperand1     OBJECT-TYPE
+	SYNTAX  Unsigned32(0..65535)
+	MAX-ACCESS  read-create
+	STATUS  current
+	DESCRIPTION
+		"For now this only refers to transport
+		protocol port number."
+	::= { fdryIpv6AclEntry 13 }
+
+fdryIpv6AclDestinationOperand2     OBJECT-TYPE
+	SYNTAX  Unsigned32(0..65535)
+	MAX-ACCESS  read-create
+	STATUS  current
+	DESCRIPTION
+		"For now this only refers to transport
+		protocol port number."
+	::= { fdryIpv6AclEntry 14 }
+
+fdryIpv6AclEstablished OBJECT-TYPE
+	SYNTAX  RtrStatus
+	MAX-ACCESS  read-create
+	STATUS  current
+	DESCRIPTION
+		"Enable/Disable the filtering of established TCP
+		packets of which the ACK or RESET flag is on. This
+		additional filter only applies to TCP transport
+		protocol."
+	::= { fdryIpv6AclEntry 15 }
+
+fdryIpv6AclLogOption OBJECT-TYPE
+	SYNTAX  TruthValue
+	MAX-ACCESS  read-create
+	STATUS  current
+	DESCRIPTION
+		"Log flag, should be set to one to enable logging"
+	::= { fdryIpv6AclEntry 16 }
+
+fdryIpv6AclComments   OBJECT-TYPE
+	SYNTAX  DisplayString (SIZE (0..255))
+	MAX-ACCESS  read-create
+	STATUS  current
+	DESCRIPTION
+		"Remark description of individual Access Control List entry."
+	::= { fdryIpv6AclEntry 17 }
+
+fdryIpv6AclRowStatus   OBJECT-TYPE
+	SYNTAX	RowStatus
+	MAX-ACCESS	read-create
+	STATUS	current
+	DESCRIPTION
+			"To create or delete a access list
+			entry."
+		::= { fdryIpv6AclEntry 18 }
+	END
+
+

mibs/FDRY-DAI-MIB

@@ -0,0 +1,286 @@
+FDRY-DAI-MIB DEFINITIONS ::= BEGIN
+
+IMPORTS
+	MODULE-IDENTITY, OBJECT-TYPE, Unsigned32, IpAddress
+	   FROM SNMPv2-SMI
+	snSwitch
+	   FROM FOUNDRY-SN-SWITCH-GROUP-MIB
+	MacAddress, TruthValue, RowStatus, TEXTUAL-CONVENTION
+	   FROM SNMPv2-TC
+	VlanIndex
+	   FROM Q-BRIDGE-MIB
+	DisplayString
+	   FROM FOUNDRY-SN-AGENT-MIB
+	ifIndex
+	   FROM IF-MIB;
+
+fdryDaiMIB MODULE-IDENTITY
+	LAST-UPDATED "201007260000Z" -- July 26, 2010
+	ORGANIZATION "Brocade Communications Systems, Inc."
+	CONTACT-INFO
+		"Technical Support Center
+              130 Holger Way,
+              San Jose, CA  95134
+              Email:  ipsupport@brocade.com
+              Phone: 1-800-752-8061
+              URL:  www.brocade.com"
+	DESCRIPTION
+		"Management Information for configuration of Dynamic ARP Inspection feature.
+		Dynamic ARP Inspection is a security mechanism which validates all ARP packets
+		in a subnet and discard those packets with invalid IP to MAC address bindings.
+
+		Copyright 1996-2010 Brocade Communications Systems, Inc.
+  		All rights reserved.
+  		This Brocade Communications Systems SNMP Management Information Base Specification
+ 		embodies Brocade Communications Systems' confidential and proprietary
+ 		intellectual property. Brocade Communications Systems retains all
+  		title and ownership in the Specification, including any revisions.
+
+ 		This Specification is supplied AS IS, and Brocade Communications Systems makes
+ 		no warranty, either express or implied, as to the use,
+ 		operation, condition, or performance of the specification, and any unintended
+ 		consequence it may on the user environment."
+
+ 	REVISION        "201007260000Z" -- July 26, 2010
+ 	DESCRIPTION
+ 		"Changed the ORGANIZATION, CONTACT-INFO and DESCRIPTION fields."
+
+	REVISION     "201002220000Z" -- February 22, 2010
+	DESCRIPTION
+		""
+   ::= { snSwitch 35}
+
+--
+-- Textual Conventions
+--
+
+ArpType ::= TEXTUAL-CONVENTION
+	STATUS	  current
+	DESCRIPTION
+		"Represents type of ARP entry to be used."
+	SYNTAX	INTEGER{
+		other(1),
+		static(2),
+		dynamic(3),
+		inspect(4),
+		dhcp(5),
+		dynamicDhcp(6),
+		staticDhcp(7),
+		host(8)
+		}
+
+ArpState ::= TEXTUAL-CONVENTION
+	STATUS	  current
+	DESCRIPTION
+		"Represents state of ARP entry to be used."
+	SYNTAX	INTEGER{
+		other(1),
+		valid(2),
+		pend(3)
+		}
+
+fdryDaiVlan  OBJECT IDENTIFIER ::= { fdryDaiMIB 1 }
+fdryDaiInterface  OBJECT IDENTIFIER ::= { fdryDaiMIB 2 }
+fdryDaiArpInspect OBJECT IDENTIFIER ::= { fdryDaiMIB 3 }
+
+--
+-- Dynamic ARP Inspection VLAN configuration table
+--
+
+fdryDaiVlanConfigTable OBJECT-TYPE
+	SYNTAX SEQUENCE OF FdryDaiVlanConfigEntry
+	MAX-ACCESS not-accessible
+	STATUS current
+	DESCRIPTION
+		"A table provides the mechanism to control Dynamic ARP
+		Inspection per VLAN. When a VLAN is created in a device
+		supporting this table, a corresponding entry of this table
+		will be added."
+	::= { fdryDaiVlan 1 }
+
+fdryDaiVlanConfigEntry OBJECT-TYPE
+	SYNTAX FdryDaiVlanConfigEntry
+	MAX-ACCESS not-accessible
+	STATUS current
+	DESCRIPTION
+		"A row instance contains the configuration to enable
+		or disable Dynamic ARP Inspection at the existing VLAN."
+	INDEX { fdryDaiVlanVLanId }
+	::= { fdryDaiVlanConfigTable 1 }
+
+FdryDaiVlanConfigEntry ::= SEQUENCE {
+	fdryDaiVlanVLanId
+		VlanIndex,
+	fdryDaiVlanDynArpInspEnable
+		TruthValue
+	}
+
+fdryDaiVlanVLanId  OBJECT-TYPE
+	SYNTAX		VlanIndex
+	MAX-ACCESS	not-accessible
+	STATUS 		current
+	DESCRIPTION
+		"This object indicates the VLAN number on which Dynamic ARP
+		Inspection feature is configured."
+	::= { fdryDaiVlanConfigEntry 1 }
+
+fdryDaiVlanDynArpInspEnable	 OBJECT-TYPE
+	SYNTAX 		TruthValue
+	MAX-ACCESS 	read-write
+	STATUS 		current
+	DESCRIPTION
+		"This object indicates whether Dynamic ARP Inspection is
+		enabled in this VLAN.
+		If this object is set to 'true', Dynamic ARP Inspection is enabled.
+		If this object is set to 'false', Dynamic ARP Inspection is disabled."
+	::= { fdryDaiVlanConfigEntry 2 }
+
+--
+-- Dynamic ARP Inspection Interface configuration table
+--
+
+fdryDaiIfConfigTable OBJECT-TYPE
+	SYNTAX SEQUENCE OF FdryDaiIfConfigEntry
+	MAX-ACCESS not-accessible
+	STATUS current
+	DESCRIPTION
+		"A table provides the mechanism to configure the trust
+		state for Dynamic ARP Inspection purpose at each physical
+		interface."
+	::= { fdryDaiInterface 1 }
+
+fdryDaiIfConfigEntry OBJECT-TYPE
+	SYNTAX FdryDaiIfConfigEntry
+	MAX-ACCESS not-accessible
+	STATUS current
+	DESCRIPTION
+		"A row instance contains the configuration to enable or
+		disable trust state for Dynamic ARP Inspection at each
+		physical interface capable of this feature."
+	INDEX { ifIndex }
+	::= { fdryDaiIfConfigTable 1 }
+
+FdryDaiIfConfigEntry ::= SEQUENCE {
+	fdryDaiIfTrustValue
+		TruthValue
+	}
+
+fdryDaiIfTrustValue  OBJECT-TYPE
+	SYNTAX		TruthValue
+	MAX-ACCESS	read-write
+	STATUS		current
+	DESCRIPTION
+		"This object indicates whether the interface is trusted for
+		Dynamic ARP Inspection.
+		If this object is set to 'true', the interface is trusted.
+		ARP packets coming to this interface will be forwarded
+		without checking.
+		If this object is set to 'false', the interface is not trusted.
+		ARP packets received on this interface will be subjected
+		to ARP inspection."
+	::= { fdryDaiIfConfigEntry 1 }
+
+--
+-- Dynamic ARP Inspection entry table
+-- Use this table to configure and display the inspection ARP entries
+--
+
+fdryDaiArpInspectTable OBJECT-TYPE
+	SYNTAX SEQUENCE OF FdryDaiArpInspectEntry
+	MAX-ACCESS not-accessible
+	STATUS current
+	DESCRIPTION
+		"A table provides the mechanism to control Dynamic ARP
+		Inspection entries. When an IP-MAC mapping entry is created
+		in a device supporting this table, a corresponding entry of this
+		table will be added."
+	::= { fdryDaiArpInspect 1 }
+
+fdryDaiArpInspectEntry OBJECT-TYPE
+	SYNTAX FdryDaiArpInspectEntry
+	MAX-ACCESS not-accessible
+	STATUS current
+	DESCRIPTION
+		"A row instance contains the configuration to map a device
+		IP address with its MAC address."
+	INDEX { fdryDaiArpInspectIpAddr }
+	::= { fdryDaiArpInspectTable 1 }
+
+FdryDaiArpInspectEntry ::= SEQUENCE {
+	fdryDaiArpInspectIpAddr
+		IpAddress,
+	fdryDaiArpInspectMacAddr
+		MacAddress,
+	fdryDaiArpInspectRowStatus
+		RowStatus,
+	fdryDaiArpInspectType
+		ArpType,
+	fdryDaiArpInspectState
+		ArpState,
+	fdryDaiArpInspectAge
+		Unsigned32,
+	fdryDaiArpInspectPort
+		DisplayString
+	}
+
+fdryDaiArpInspectIpAddr  OBJECT-TYPE
+	SYNTAX		IpAddress
+	MAX-ACCESS	not-accessible
+	STATUS		current
+	DESCRIPTION
+		"The device IP address."
+	::= { fdryDaiArpInspectEntry 1}
+
+fdryDaiArpInspectMacAddr  OBJECT-TYPE
+	SYNTAX		MacAddress
+	MAX-ACCESS	read-create
+	STATUS		current
+	DESCRIPTION
+		"The device MAC address."
+	::= { fdryDaiArpInspectEntry 2 }
+
+fdryDaiArpInspectRowStatus  OBJECT-TYPE
+ 	SYNTAX  RowStatus
+ 	MAX-ACCESS  read-create
+ 	STATUS  current
+ 	DESCRIPTION
+ 		"This variable is used to create, or
+ 		delete a row in this table. When a row in this
+ 		table is in active(1) state, no objects in that row
+ 		can be modified except this object."
+ 	::= { fdryDaiArpInspectEntry 3 }
+
+fdryDaiArpInspectType OBJECT-TYPE
+	SYNTAX     ArpType
+	MAX-ACCESS read-only
+	STATUS     current
+	DESCRIPTION
+		"The type of the ARP entry"
+	::= { fdryDaiArpInspectEntry 4 }
+
+fdryDaiArpInspectState OBJECT-TYPE
+	SYNTAX     ArpState
+	MAX-ACCESS read-only
+	STATUS     current
+	DESCRIPTION
+		"The state of the ARP entry"
+	::= { fdryDaiArpInspectEntry 5 }
+
+fdryDaiArpInspectAge OBJECT-TYPE
+	SYNTAX    Unsigned32
+	MAX-ACCESS read-only
+	STATUS     current
+	DESCRIPTION
+		"The timer of the ARP entry"
+	::= { fdryDaiArpInspectEntry 6 }
+
+fdryDaiArpInspectPort OBJECT-TYPE
+	SYNTAX    DisplayString
+	MAX-ACCESS read-only
+	STATUS     current
+	DESCRIPTION
+		"The port of the ARP entry"
+	::= { fdryDaiArpInspectEntry 7 }
+
+   END
+

mibs/FDRY-DHCP-SNOOPING-MIB

@@ -0,0 +1,286 @@
+FDRY-DHCP-SNOOPING-MIB DEFINITIONS ::= BEGIN
+
+IMPORTS
+	MODULE-IDENTITY, OBJECT-TYPE, Unsigned32, IpAddress
+	   FROM SNMPv2-SMI
+	snSwitch
+	   FROM FOUNDRY-SN-SWITCH-GROUP-MIB
+	ArpType, ArpState
+	   FROM FDRY-DAI-MIB
+	MacAddress, TruthValue, TEXTUAL-CONVENTION
+	   FROM SNMPv2-TC
+	VlanIndex
+	   FROM Q-BRIDGE-MIB
+	DisplayString
+	   FROM FOUNDRY-SN-AGENT-MIB
+	ifIndex
+	   FROM IF-MIB;
+
+fdryDhcpSnoopMIB MODULE-IDENTITY
+	LAST-UPDATED "201007260000Z" -- July 26, 2010
+	ORGANIZATION "Brocade Communications Systems, Inc."
+	CONTACT-INFO
+		"Technical Support Center
+              130 Holger Way,
+              San Jose, CA  95134
+              Email:  ipsupport@brocade.com
+              Phone: 1-800-752-8061
+              URL:  www.brocade.com"
+	DESCRIPTION
+		"Management Information for configuration of DHCP Snooping feature.
+		DHCP Snooping  is a security feature which enables the device to filter
+		untrusted DHCP packets in a subnet. It can also stop unauthorized DHCP
+		serves and prevent errors due to user mis-configuration servers.
+
+		Copyright 1996-2010 Brocade Communications Systems, Inc.
+  		All rights reserved.
+  		This Brocade Communications Systems SNMP Management Information Base Specification
+ 		embodies Brocade Communications Systems' confidential and proprietary
+ 		intellectual property. Brocade Communications Systems retains all
+  		title and ownership in the Specification, including any revisions.
+
+ 		This Specification is supplied AS IS, and Brocade Communications Systems makes
+ 		no warranty, either express or implied, as to the use,
+ 		operation, condition, or performance of the specification, and any unintended
+ 		consequence it may on the user environment."
+
+ 	REVISION        "201007260000Z" -- July 26, 2010
+ 	DESCRIPTION
+ 		"Changed the ORGANIZATION, CONTACT-INFO and DESCRIPTION fields."
+
+	REVISION     "201003220000Z" -- March 22, 2010
+	DESCRIPTION
+		""
+   ::= { snSwitch 36}
+
+--
+-- Textual Conventions
+--
+
+ClearAction ::= TEXTUAL-CONVENTION
+	STATUS	  current
+	DESCRIPTION
+		"Represents action of Clear operation to be used."
+	SYNTAX	INTEGER{
+		valid(0),
+		clear(1)
+		}
+
+fdryDhcpSnoopGlobalObjects  OBJECT IDENTIFIER ::= { fdryDhcpSnoopMIB 1 }
+fdryDhcpSnoopVlan  OBJECT IDENTIFIER ::= { fdryDhcpSnoopMIB 2 }
+fdryDhcpSnoopInterface  OBJECT IDENTIFIER ::= { fdryDhcpSnoopMIB 3 }
+fdryDhcpSnoopBind OBJECT IDENTIFIER ::= { fdryDhcpSnoopMIB 4 }
+
+--
+-- DHCP Snooping global Scalar Object
+--
+
+fdryDhcpSnoopGlobalClearOper OBJECT-TYPE
+    SYNTAX     ClearAction
+    MAX-ACCESS read-write
+    STATUS     current
+    DESCRIPTION
+        "valid(0) - this value is always returned when the variable is read.
+         clear(1) - setting the variable to this value clears all entries in the
+         DHCP binding database."
+    ::= { fdryDhcpSnoopGlobalObjects 1 }
+
+--
+-- DHCP Snooping VLAN configuration table
+--
+
+fdryDhcpSnoopVlanConfigTable OBJECT-TYPE
+	SYNTAX SEQUENCE OF FdryDhcpSnoopVlanConfigEntry
+	MAX-ACCESS not-accessible
+	STATUS current
+	DESCRIPTION
+		"A table provides the mechanism to control DHCP Snooping
+		per VLAN. When a VLAN is created in a device
+		supporting this table, a corresponding entry of this table
+		will be added."
+	::= { fdryDhcpSnoopVlan 1 }
+
+fdryDhcpSnoopVlanConfigEntry OBJECT-TYPE
+	SYNTAX FdryDhcpSnoopVlanConfigEntry
+	MAX-ACCESS not-accessible
+	STATUS current
+	DESCRIPTION
+		"A row instance contains the configuration to enable
+		or disable DHCP Snooping at the existing VLAN."
+	INDEX { fdryDhcpSnoopVlanVLanId }
+	::= { fdryDhcpSnoopVlanConfigTable 1 }
+
+FdryDhcpSnoopVlanConfigEntry ::= SEQUENCE {
+	fdryDhcpSnoopVlanVLanId
+		VlanIndex,
+	fdryDhcpSnoopVlanDhcpSnoopEnable
+		TruthValue
+	}
+
+fdryDhcpSnoopVlanVLanId  OBJECT-TYPE
+	SYNTAX		VlanIndex
+	MAX-ACCESS	not-accessible
+	STATUS 		current
+	DESCRIPTION
+		"This object indicates the VLAN number on which DHCP
+		Snooping feature is configured."
+	::= { fdryDhcpSnoopVlanConfigEntry 1 }
+
+fdryDhcpSnoopVlanDhcpSnoopEnable	 OBJECT-TYPE
+	SYNTAX 		TruthValue
+	MAX-ACCESS 	read-write
+	STATUS 		current
+	DESCRIPTION
+		"This object indicates whether DHCP Snooping is enabled in this VLAN.
+
+		If this object is set to 'true', DHCP Snooping is enabled.
+		If this object is set to 'false', DHCP Snooping is disabled."
+	::= { fdryDhcpSnoopVlanConfigEntry 2 }
+
+--
+-- DHCP Snooping Interface configuration table
+--
+
+fdryDhcpSnoopIfConfigTable OBJECT-TYPE
+	SYNTAX SEQUENCE OF FdryDhcpSnoopIfConfigEntry
+	MAX-ACCESS not-accessible
+	STATUS current
+	DESCRIPTION
+		"A table provides the mechanism to configure the trust
+		state for DHCP Snooping purpose at each physical
+		interface."
+	::= { fdryDhcpSnoopInterface 1 }
+
+fdryDhcpSnoopIfConfigEntry OBJECT-TYPE
+	SYNTAX FdryDhcpSnoopIfConfigEntry
+	MAX-ACCESS not-accessible
+	STATUS current
+	DESCRIPTION
+		"A row instance contains the configuration to enable or
+		disable trust state for DHCP Snooping at each
+		physical interface capable of this feature."
+	INDEX { ifIndex }
+	::= { fdryDhcpSnoopIfConfigTable 1 }
+
+FdryDhcpSnoopIfConfigEntry ::= SEQUENCE {
+	fdryDhcpSnoopIfTrustValue
+		TruthValue
+	}
+
+fdryDhcpSnoopIfTrustValue  OBJECT-TYPE
+	SYNTAX		TruthValue
+	MAX-ACCESS	read-write
+	STATUS		current
+	DESCRIPTION
+		"This object indicates whether the interface is trusted for
+		DHCP Snooping.
+		If this object is set to 'true', the interface is trusted.
+		DHCP packets coming to this interface will be forwarded
+		without checking.
+		If this object is set to 'false', the interface is not trusted.
+		DHCP packets received on this interface will be subjected
+		to DHCP checks."
+	::= { fdryDhcpSnoopIfConfigEntry 1 }
+
+--
+-- DHCP Snooping binding database table
+-- Use this table to display DHCP Snooping entries
+--
+
+fdryDhcpSnoopBindTable OBJECT-TYPE
+	SYNTAX SEQUENCE OF FdryDhcpSnoopBindEntry
+	MAX-ACCESS not-accessible
+	STATUS current
+	DESCRIPTION
+		"A table provides the information of DHCP snooping
+		binding database learnt by the device"
+	::= { fdryDhcpSnoopBind 1 }
+
+fdryDhcpSnoopBindEntry OBJECT-TYPE
+	SYNTAX FdryDhcpSnoopBindEntry
+	MAX-ACCESS not-accessible
+	STATUS current
+	DESCRIPTION
+		"A row instance contains the information of DHCP snoonping entry."
+	INDEX { fdryDhcpSnoopBindIpAddr }
+	::= { fdryDhcpSnoopBindTable 1 }
+
+FdryDhcpSnoopBindEntry ::= SEQUENCE {
+	fdryDhcpSnoopBindIpAddr
+		IpAddress,
+	fdryDhcpSnoopBindMacAddr
+		MacAddress,
+	fdryDhcpSnoopBindType
+		ArpType,
+	fdryDhcpSnoopBindState
+		ArpState,
+	fdryDhcpSnoopBindPort
+		DisplayString,
+	fdryDhcpSnoopBindVlanId
+		VlanIndex,
+	fdryDhcpSnoopBindClearOper
+		ClearAction
+	}
+
+fdryDhcpSnoopBindIpAddr  OBJECT-TYPE
+	SYNTAX		IpAddress
+	MAX-ACCESS	not-accessible
+	STATUS		current
+	DESCRIPTION
+		"The device IP address."
+	::= { fdryDhcpSnoopBindEntry 1}
+
+fdryDhcpSnoopBindMacAddr  OBJECT-TYPE
+	SYNTAX		MacAddress
+	MAX-ACCESS	read-only
+	STATUS		current
+	DESCRIPTION
+		"The device MAC address."
+	::= { fdryDhcpSnoopBindEntry 2 }
+
+fdryDhcpSnoopBindType OBJECT-TYPE
+	SYNTAX     ArpType
+	MAX-ACCESS read-only
+	STATUS     current
+	DESCRIPTION
+		"The type of the ARP entry"
+	::= { fdryDhcpSnoopBindEntry 3 }
+
+fdryDhcpSnoopBindState OBJECT-TYPE
+	SYNTAX    ArpState
+	MAX-ACCESS read-only
+	STATUS     current
+	DESCRIPTION
+		"The state of the ARP entry"
+	::= { fdryDhcpSnoopBindEntry 4 }
+
+fdryDhcpSnoopBindPort OBJECT-TYPE
+	SYNTAX    DisplayString
+	MAX-ACCESS read-only
+	STATUS     current
+	DESCRIPTION
+		"The port of the ARP entry"
+	::= { fdryDhcpSnoopBindEntry 5 }
+
+fdryDhcpSnoopBindVlanId  OBJECT-TYPE
+	SYNTAX		VlanIndex
+	MAX-ACCESS	read-only
+	STATUS 		current
+	DESCRIPTION
+		"This object indicates the VLAN number on which DHCP snooping
+		feature is configured."
+	::= { fdryDhcpSnoopBindEntry 6 }
+
+fdryDhcpSnoopBindClearOper OBJECT-TYPE
+	SYNTAX    ClearAction
+	MAX-ACCESS read-write
+	STATUS     current
+	DESCRIPTION
+		 "valid(0) - this value is always returned when the variable is read.
+         	clear(1) - setting the variable to this value clears this entry in the
+        	 DHCP binding database."
+	::= {fdryDhcpSnoopBindEntry 7 }
+
+
+   END
+

mibs/FDRY-DNS2-MIB

@@ -0,0 +1,190 @@
+FDRY-DNS2-MIB DEFINITIONS ::= BEGIN
+
+IMPORTS
+    MODULE-IDENTITY, Unsigned32,
+    OBJECT-TYPE         FROM SNMPv2-SMI                 -- [RFC2578]
+    DisplayString, RowStatus
+                        FROM SNMPv2-TC                  -- [RFC2579]
+    InetAddressType, InetAddress
+                        FROM INET-ADDRESS-MIB           -- [RFC 4001]
+    ;
+
+fdryDns2MIB MODULE-IDENTITY
+    LAST-UPDATED "201006020000Z"  -- 04 June 2010
+    ORGANIZATION "Brocade Communications Systems, Inc."
+    CONTACT-INFO
+             "Technical Support Center
+              130 Holger Way,
+              San Jose, CA  95134
+              Email:  ipsupport@brocade.com
+              Phone: 1-800-752-8061
+              URL:  www.brocade.com"
+    DESCRIPTION
+             "The Brocade proprietary MIB module for Domain Name Service(DNS)
+              It has new IPv4/IPv6 combined tables for Domain Name Service Address List and Name configuration.
+
+              Copyright 1996-2010 Brocade Communications Systems, Inc.
+              All rights reserved.
+              This Brocade Communications Systems SNMP Management Information Base Specification
+              embodies Brocade Communications Systems' confidential and proprietary
+              intellectual property. Brocade Communications Systems retains all
+              title and ownership in the Specification, including any revisions.
+
+              This Specification is supplied AS IS, and Brocade Communications Systems makes
+              no warranty, either express or implied, as to the use,
+              operation, condition, or performance of the specification, and any unintended
+              consequence it may on the user environment."
+
+    REVISION        "201006020000Z"  -- 04 June 2010
+    DESCRIPTION
+        "Changed the ORGANIZATION, CONTACT-INFO and DESCRIPTION fields."
+
+    REVISION 	"200901300000Z"  -- 30 Jan 2009
+    DESCRIPTION "Initial version, obsoletes the earlier mib groups to resolve the mib conflicts.
+    			fdryDns2MIB obsoletes fdryDnsMIB,
+				fdryDns2DomainName obsoletes fdryDnsDomainName,
+				fdryDnsServer obsoletes fdryDnsServerAddress"
+
+    ::= { iso(1) org(3) dod(6) internet(1) private(4) enterprises(1) foundry(1991) products(1) switch(1) snSwitch(3) 34 }
+
+    --
+    -- Top level components of this MIB.
+    --
+
+    fdryDns2DomainName      OBJECT IDENTIFIER ::= { fdryDns2MIB 1 }
+    fdryDnsServer           OBJECT IDENTIFIER ::= { fdryDns2MIB 2 }
+
+    --
+    -- Ipv4/Ipv6  mib table for Domain Name Service (DNS) Domain Name
+    --
+
+    fdryDns2DomainNameTable      OBJECT-TYPE
+        SYNTAX  SEQUENCE OF FdryDns2DomainNameEntry
+        MAX-ACCESS  not-accessible
+        STATUS  current
+        DESCRIPTION
+            "Domain Name Service domain name table."
+        ::= { fdryDns2DomainName 1 }
+
+    fdryDns2DomainNameEntry      OBJECT-TYPE
+        SYNTAX  FdryDns2DomainNameEntry
+        MAX-ACCESS  not-accessible
+        STATUS  current
+        DESCRIPTION
+            "An entry in the DNS domain name table."
+        INDEX   { fdryDns2DomainNameIndex }
+        ::= { fdryDns2DomainNameTable 1 }
+
+    FdryDns2DomainNameEntry ::= SEQUENCE {
+        fdryDns2DomainNameIndex         Unsigned32,
+        fdryDns2DomainNameAddrType      InetAddressType,
+        fdryDns2DomainNameName          DisplayString,
+        fdryDns2DomainNameRowStatus     RowStatus
+        }
+
+    fdryDns2DomainNameIndex OBJECT-TYPE
+        SYNTAX  Unsigned32
+        MAX-ACCESS  not-accessible
+        STATUS  current
+        DESCRIPTION
+            "The index to the DNS name table."
+        ::= { fdryDns2DomainNameEntry 1 }
+
+    fdryDns2DomainNameAddrType           OBJECT-TYPE
+        SYNTAX  InetAddressType
+        MAX-ACCESS  read-create
+        STATUS  current
+        DESCRIPTION
+              "DNS IP address Type. Supported address types are ipv4(1) and ipv6(2)"
+        DEFVAL  { ipv4 }
+        ::= { fdryDns2DomainNameEntry 2 }
+
+    fdryDns2DomainNameName OBJECT-TYPE
+        SYNTAX  DisplayString (SIZE(0..64))
+        MAX-ACCESS  read-create
+        STATUS  current
+        DESCRIPTION
+            "Domain Name Service Domain Name string."
+        ::= { fdryDns2DomainNameEntry 3 }
+
+    fdryDns2DomainNameRowStatus  OBJECT-TYPE
+        SYNTAX  RowStatus
+        MAX-ACCESS  read-create
+        STATUS  current
+        DESCRIPTION
+            "This variable is used to create, modify, or
+             delete a row in this table. When a row in this
+             table is in active(1) state, no objects in that row
+             can be modified except this object."
+        ::= { fdryDns2DomainNameEntry 4 }
+
+    --
+    -- IPv4/IPv6 MIB table for DNS servers
+    --
+
+    fdryDnsServerTable       OBJECT-TYPE
+        SYNTAX      SEQUENCE OF FdryDnsServerEntry
+        MAX-ACCESS  not-accessible
+        STATUS      current
+        DESCRIPTION
+            "DNS server table, listing the Ipv4/Ipv6 DNS server addresses"
+        ::= { fdryDnsServer 1 }
+
+    fdryDnsServerEntry       OBJECT-TYPE
+        SYNTAX      FdryDnsServerEntry
+        MAX-ACCESS  not-accessible
+        STATUS      current
+        DESCRIPTION
+            "An entry in the DNS server table."
+
+        INDEX   {fdryDnsServerAddrType, fdryDnsServerIndex}
+        ::= { fdryDnsServerTable 1 }
+
+    FdryDnsServerEntry ::= SEQUENCE {
+        fdryDnsServerAddrType
+            InetAddressType,
+        fdryDnsServerIndex
+            Unsigned32,
+        fdryDnsServerAddr
+            InetAddress,
+        fdryDnsServerRowStatus
+            RowStatus
+        }
+    fdryDnsServerAddrType OBJECT-TYPE
+        SYNTAX      InetAddressType
+        MAX-ACCESS  not-accessible
+        STATUS      current
+        DESCRIPTION
+              "The index to the DNS server table. DNS server IP address type. Supported address types are ipv4(1) and ipv6(2)"
+        DEFVAL  { ipv4 }
+        ::= { fdryDnsServerEntry 1 }
+
+    fdryDnsServerIndex OBJECT-TYPE
+        SYNTAX      Unsigned32
+        MAX-ACCESS  not-accessible
+        STATUS      current
+        DESCRIPTION
+            "The index to the DNS server table.  Currently, up to 4 DNS server
+             entries each are supported for IPv4 and IPv6."
+        ::= { fdryDnsServerEntry 2 }
+
+    fdryDnsServerAddr OBJECT-TYPE
+        SYNTAX      InetAddress
+        MAX-ACCESS  read-create
+        STATUS      current
+        DESCRIPTION
+              "DNS server IP address."
+        ::= { fdryDnsServerEntry 3 }
+
+    fdryDnsServerRowStatus OBJECT-TYPE
+        SYNTAX      RowStatus
+        MAX-ACCESS  read-create
+        STATUS      current
+        DESCRIPTION
+            "This variable is used to create, modify, or
+             delete a row in this table. When a row in this
+             table is in active(1) state, no objects in that row
+             can be modified except this object."
+        ::= { fdryDnsServerEntry 4 }
+
+END

mibs/FDRY-IP-SOURCE-GUARD-MIB

@@ -0,0 +1,263 @@
+FDRY-IP-SOURCE-GUARD-MIB DEFINITIONS ::= BEGIN
+
+IMPORTS
+	MODULE-IDENTITY, OBJECT-TYPE, Unsigned32, IpAddress
+	   FROM SNMPv2-SMI
+	snSwitch
+	   FROM FOUNDRY-SN-SWITCH-GROUP-MIB
+	TruthValue, RowStatus, TEXTUAL-CONVENTION
+	   FROM SNMPv2-TC
+	VlanIndex
+	   FROM Q-BRIDGE-MIB
+	ifIndex, InterfaceIndex
+	   FROM IF-MIB;
+
+fdryIpSrcGuardMIB MODULE-IDENTITY
+	LAST-UPDATED "201007260000Z" -- July 26, 2010
+	ORGANIZATION "Brocade Communications Systems, Inc."
+	CONTACT-INFO
+		"Technical Support Center
+              130 Holger Way,
+              San Jose, CA  95134
+              Email:  ipsupport@brocade.com
+              Phone: 1-800-752-8061
+              URL:  www.brocade.com"
+	DESCRIPTION
+		"Management Information for configuration of IP Source Guard feature.
+		IP Source Guard is a security feature that restricts IP traffic on untrusted
+		ports by filtering traffic based on the DHCP snooping binding database or
+		manually configured IP source bindings.
+
+		Copyright 1996-2010 Brocade Communications Systems, Inc.
+  		All rights reserved.
+  		This Brocade Communications Systems SNMP Management Information Base Specification
+ 		embodies Brocade Communications Systems' confidential and proprietary
+ 		intellectual property. Brocade Communications Systems retains all
+  		title and ownership in the Specification, including any revisions.
+
+ 		This Specification is supplied AS IS, and Brocade Communications Systems makes
+ 		no warranty, either express or implied, as to the use,
+ 		operation, condition, or performance of the specification, and any unintended
+ 		consequence it may on the user environment."
+
+ 	REVISION        "201007260000Z" -- July 26, 2010
+ 	DESCRIPTION
+ 		"Changed the ORGANIZATION, CONTACT-INFO and DESCRIPTION fields."
+
+	REVISION     "201002220000Z" -- February 22, 2010
+	DESCRIPTION
+		""
+   ::= { snSwitch 37}
+
+BindMode ::= TEXTUAL-CONVENTION
+	STATUS	  current
+	DESCRIPTION
+		"Represents mode of the IP Source Guard entry."
+	SYNTAX     INTEGER {
+		other(1),
+		active(2),
+		inactive(3)
+		}
+
+BindType ::= TEXTUAL-CONVENTION
+	STATUS	  current
+	DESCRIPTION
+		"Represents type of the IP Source Guard entry."
+	SYNTAX     INTEGER {
+		other(1),
+		ip(2)
+		}
+
+fdryIpSrcGuardInterface  OBJECT IDENTIFIER ::= { fdryIpSrcGuardMIB 1 }
+fdryIpSrcGuardPortVlan OBJECT IDENTIFIER ::= { fdryIpSrcGuardMIB 2 }
+fdryIpSrcGuardBind OBJECT IDENTIFIER ::= { fdryIpSrcGuardMIB 3 }
+
+--
+-- IP Source Guard Interface configuration table
+--
+
+fdryIpSrcGuardIfConfigTable OBJECT-TYPE
+	SYNTAX SEQUENCE OF FdryIpSrcGuardIfConfigEntry
+	MAX-ACCESS not-accessible
+	STATUS current
+	DESCRIPTION
+		"A table provides the mechanism to configure enabling or disabling
+		IP Source Guard purpose at each physical interface."
+	::= { fdryIpSrcGuardInterface 1 }
+
+fdryIpSrcGuardIfConfigEntry OBJECT-TYPE
+	SYNTAX FdryIpSrcGuardIfConfigEntry
+	MAX-ACCESS not-accessible
+	STATUS current
+	DESCRIPTION
+		"A row instance contains the configuration to enable or disable IP
+		Source Guard at each physical interface capable of this feature."
+	INDEX { ifIndex }
+	::= { fdryIpSrcGuardIfConfigTable 1 }
+
+FdryIpSrcGuardIfConfigEntry ::= SEQUENCE {
+	fdryIpSrcGuardIfEnable
+		TruthValue
+	}
+
+fdryIpSrcGuardIfEnable  OBJECT-TYPE
+	SYNTAX		TruthValue
+	MAX-ACCESS	read-write
+	STATUS		current
+	DESCRIPTION
+		"This object indicates whether IP Source Guard is
+		enabled  at this interface.
+		If this object is set to 'true', IP Source Guard is enabled.
+		Traffic  coming to this interface will be forwarded. If it is
+		 from the list of IP addresses obtained from DHCP snooping.
+		 Otherwise it is denied.
+		If this object is set to 'false', IP Source Guard is disabled."
+	::= { fdryIpSrcGuardIfConfigEntry 1 }
+
+--
+-- IP Source Guard per-port-per-VLAN configuration table
+--
+
+fdryIpSrcGuardPortVlanConfigTable OBJECT-TYPE
+	SYNTAX SEQUENCE OF FdryIpSrcGuardPortVlanConfigEntry
+	MAX-ACCESS not-accessible
+	STATUS current
+	DESCRIPTION
+		"A table provides the mechanism to configure enabling or disabling
+		IP Source Guard purpose per port per VLAN."
+	::= { fdryIpSrcGuardPortVlan 1 }
+
+fdryIpSrcGuardPortVlanConfigEntry OBJECT-TYPE
+	SYNTAX FdryIpSrcGuardPortVlanConfigEntry
+	MAX-ACCESS not-accessible
+	STATUS current
+	DESCRIPTION
+		"A row instance contains the configuration to enable or disable IP
+		Source Guard per port per VLAN of this feature."
+	INDEX { fdryIpSrcGuardPortVlanPortId, fdryIpSrcGuardPortVlanVlanId }
+	::= { fdryIpSrcGuardPortVlanConfigTable 1 }
+
+FdryIpSrcGuardPortVlanConfigEntry ::= SEQUENCE {
+	fdryIpSrcGuardPortVlanPortId
+		InterfaceIndex,
+	fdryIpSrcGuardPortVlanVlanId
+		VlanIndex,
+	fdryIpSrcGuardPortVlanEnable
+		TruthValue
+	}
+
+fdryIpSrcGuardPortVlanPortId OBJECT-TYPE
+    SYNTAX     InterfaceIndex
+    MAX-ACCESS not-accessible
+    STATUS     current
+    DESCRIPTION
+        "The ifIndex of the port for IP Source Guard purpose per port per VLAN."
+    ::= { fdryIpSrcGuardPortVlanConfigEntry 1 }
+
+fdryIpSrcGuardPortVlanVlanId OBJECT-TYPE
+    SYNTAX     VlanIndex
+    MAX-ACCESS not-accessible
+    STATUS     current
+    DESCRIPTION
+        "The number of VLAN for IP Source Guard purpose per port per VLAN."
+    ::= { fdryIpSrcGuardPortVlanConfigEntry 2 }
+
+fdryIpSrcGuardPortVlanEnable  OBJECT-TYPE
+	SYNTAX		TruthValue
+	MAX-ACCESS	read-write
+	STATUS		current
+	DESCRIPTION
+		"This object indicates whether IP Source Guard is
+		enabled at this interface and this VLAN number.
+		If this object is set to 'true', IP Source Guard per-port-per-VLAN is enabled.
+		If this object is set to 'false', IP Source Guard per-port-per-VLAN is disabled."
+	::= { fdryIpSrcGuardPortVlanConfigEntry 3 }
+
+--
+-- IP Source Guard binding table
+-- Use this table to configure Ip source entries
+--
+
+fdryIpSrcGuardBindTable OBJECT-TYPE
+	SYNTAX SEQUENCE OF FdryIpSrcGuardBindEntry
+	MAX-ACCESS not-accessible
+	STATUS current
+	DESCRIPTION
+		"A table provides the information of IP addresses used IP Source
+		Guard purpose at each physical interface with or without specific VLAN
+		memberships  "
+	::= { fdryIpSrcGuardBind 1 }
+
+fdryIpSrcGuardBindEntry OBJECT-TYPE
+	SYNTAX FdryIpSrcGuardBindEntry
+	MAX-ACCESS not-accessible
+	STATUS current
+	DESCRIPTION
+		"A row instance contains IP address used for IP Source Guard purpose
+		at each physical interface with or without specific VLAN memberships ."
+	INDEX { ifIndex, fdryIpSrcGuardBindIpAddr }
+	::= { fdryIpSrcGuardBindTable 1 }
+
+FdryIpSrcGuardBindEntry ::= SEQUENCE {
+	fdryIpSrcGuardBindIpAddr
+		IpAddress,
+	fdryIpSrcGuardBindVlanId
+		Unsigned32,
+	fdryIpSrcGuardBindRowStatus
+		RowStatus,
+	fdryIpSrcGuardBindMode
+		BindMode,
+	fdryIpSrcGuardBindType
+		BindType
+	}
+
+fdryIpSrcGuardBindIpAddr  OBJECT-TYPE
+	SYNTAX		IpAddress
+	MAX-ACCESS	not-accessible
+	STATUS		current
+	DESCRIPTION
+		"The device IP address."
+	::= { fdryIpSrcGuardBindEntry 1}
+
+fdryIpSrcGuardBindVlanId  OBJECT-TYPE
+	SYNTAX		Unsigned32
+	MAX-ACCESS	read-create
+	STATUS 		current
+	DESCRIPTION
+		"This object indicates the specific VLAN memberships on this interface.
+		The VLAN number is optional. If you configure a VLAN number, the bindings
+		applies to that VLAN only. If you do not configure a VLAN number, the static
+		applies to all VLANs associated with the port. In this case, the VLAN number
+		will be displayed as 0."
+	::= { fdryIpSrcGuardBindEntry 2 }
+
+fdryIpSrcGuardBindRowStatus  OBJECT-TYPE
+ 	SYNTAX  RowStatus
+ 	MAX-ACCESS  read-create
+ 	STATUS  current
+ 	DESCRIPTION
+ 		"This variable is used to create, or
+ 		delete a row in this table. When a row in this
+ 		table is in active(1) state, no objects in that row
+ 		can be modified except this object."
+ 	::= { fdryIpSrcGuardBindEntry 3 }
+
+fdryIpSrcGuardBindMode OBJECT-TYPE
+	SYNTAX    BindMode
+	MAX-ACCESS read-only
+	STATUS     current
+	DESCRIPTION
+		"The mode of the IP Source Guard entry"
+	::= { fdryIpSrcGuardBindEntry 4 }
+
+fdryIpSrcGuardBindType OBJECT-TYPE
+	SYNTAX    BindType
+	MAX-ACCESS read-only
+	STATUS     current
+	DESCRIPTION
+		"The type of the IP Source Guard entry"
+	::= { fdryIpSrcGuardBindEntry 5 }
+
+
+   END
+

mibs/FDRY-IPV6-IP-MIB

@@ -0,0 +1,76 @@
+FDRY-IPV6-IP-MIB DEFINITIONS ::= BEGIN
+
+IMPORTS
+    MODULE-IDENTITY, OBJECT-TYPE, Unsigned32
+      FROM SNMPv2-SMI       -- [RFC2578]
+    RtrStatus
+      FROM FOUNDRY-SN-IP-MIB  --[snrouteru.mib]
+    fdryIpv6
+      FROM FOUNDRY-SN-ROOT-MIB -- [snrootu.mib]
+   ;
+
+fdryIpv6MIB MODULE-IDENTITY
+	LAST-UPDATED "201007260000Z" -- July 26, 2010
+	ORGANIZATION "Brocade Communications Systems, Inc."
+	CONTACT-INFO
+		"Technical Support Center
+              130 Holger Way,
+              San Jose, CA  95134
+              Email:  ipsupport@brocade.com
+              Phone: 1-800-752-8061
+              URL:  www.brocade.com"
+    DESCRIPTION
+        "The Brocade proprietary MIB module for IPv6.
+
+         Copyright 1996-2010 Brocade Communications Systems, Inc.
+  		All rights reserved.
+  		This Brocade Communications Systems SNMP Management Information Base Specification
+ 		embodies Brocade Communications Systems' confidential and proprietary
+ 		intellectual property. Brocade Communications Systems retains all
+  		title and ownership in the Specification, including any revisions.
+
+ 		This Specification is supplied AS IS, and Brocade Communications Systems makes
+ 		no warranty, either express or implied, as to the use,
+ 		operation, condition, or performance of the specification, and any unintended
+ 		consequence it may on the user environment."
+
+ 	REVISION        "201007260000Z" -- July 26, 2010
+ 	DESCRIPTION
+ 		"Changed the ORGANIZATION, CONTACT-INFO and DESCRIPTION fields."
+
+	REVISION	 "201005060000Z"  -- 06 May 2010
+	DESCRIPTION  ""
+
+   ::= { fdryIpv6 1 }
+
+
+--
+-- Top level components of this MIB.
+--
+
+fdryIpv6GlobalObjects   		OBJECT IDENTIFIER ::= { fdryIpv6MIB 1 }
+
+
+--
+-- Ipv6 global Scalar Object
+--
+
+fdryIpv6LoadShare         OBJECT-TYPE
+	SYNTAX  RtrStatus
+	MAX-ACCESS  read-write
+	STATUS  current
+	DESCRIPTION
+		"If more than one ipv6 route available,
+		use them to share load."
+	::= { fdryIpv6GlobalObjects 1}
+
+fdryIpv6LoadShareNumOfPaths	OBJECT-TYPE
+	SYNTAX Unsigned32
+	MAX-ACCESS  read-write
+	STATUS  current
+	DESCRIPTION
+		"Number of ipv6 routes are used to share load."
+	::= { fdryIpv6GlobalObjects 2 }
+
+END
+

mibs/FDRY-MPLS-L2VPN-MIB

@@ -0,0 +1,899 @@
+FDRY-MPLS-L2VPN-MIB DEFINITIONS ::= BEGIN
+IMPORTS
+   NOTIFICATION-TYPE, MODULE-IDENTITY, OBJECT-TYPE,
+   Unsigned32, Counter64
+      FROM SNMPv2-SMI                                     -- [RFC2578]
+   TEXTUAL-CONVENTION, RowStatus, TruthValue
+      FROM SNMPv2-TC                                      -- [RFC2579]
+   InterfaceIndex
+      FROM IF-MIB                                         -- [RFC2863]
+   VlanTagMode, PortPriorityTC
+      FROM FOUNDRY-SN-SWITCH-GROUP-MIB                    -- [snswitch]
+   snMpls
+      FROM FOUNDRY-SN-ROOT-MIB                            -- [snroot]
+   vplsConfigName, vplsConfigIndex, vplsConfigEntry
+      FROM VPLS-GENERIC-DRAFT-01-MIB                      -- [draft-ietf-l2vpn-vpls-mib-00]
+   PwOperStatusTC, PwVlanCfg
+      FROM PW-TC-STD-MIB                                  -- [draft-ietf-pw3-pw-tc-mib-11]
+   pwIndex, pwName, pwID, fdryPwServiceType
+      FROM PW-STD-MIB                                     -- [draft-ietf-pw3-pw-mib-11]
+   pwEnetPwInstance
+      FROM PW-ENET-STD-MIB                                -- [draft-ietf-pw3-enet-mib-11]
+   ;
+
+fdryMplsL2VpnMIB MODULE-IDENTITY
+    LAST-UPDATED "201006020000Z"  -- 04 June 2010
+    ORGANIZATION "Brocade Communications Systems, Inc."
+    CONTACT-INFO
+             "Technical Support Center
+              130 Holger Way,
+              San Jose, CA  95134
+              Email:  ipsupport@brocade.com
+              Phone: 1-800-752-8061
+              URL:  www.brocade.com"
+    DESCRIPTION
+             "The Brocade proprietary MIB module for L2 VPN.
+              This mib is built on the current L2VPN draft mib.
+              It has additional information for Virtual Leased Line (VLL),
+              VLL-Local and Virtual Private LAN Service (VPLS) Endpoints,
+              as well as for VPLS Instance.
+
+              Copyright 1996-2010 Brocade Communications Systems, Inc.
+              All rights reserved.
+              This Brocade Communications Systems SNMP Management Information Base Specification
+              embodies Brocade Communications Systems' confidential and proprietary
+              intellectual property. Brocade Communications Systems retains all
+              title and ownership in the Specification, including any revisions.
+
+              This Specification is supplied AS IS, and Brocade Communications Systems makes
+              no warranty, either express or implied, as to the use,
+              operation, condition, or performance of the specification, and any unintended
+              consequence it may on the user environment."
+
+    REVISION        "201006020000Z"  -- 04 June 2010
+    DESCRIPTION
+        "Changed the ORGANIZATION, CONTACT-INFO and DESCRIPTION fields."
+
+    REVISION      "200802070000Z"  -- 7 February 2008
+    DESCRIPTION
+            "Initial revision"
+   ::= { snMpls 2 }
+
+--
+-- Textual Conventions
+--
+MplsServiceType ::= TEXTUAL-CONVENTION
+   STATUS        current
+   DESCRIPTION
+       "MPLS VLL service types, VLL, VLL-local or VPLS."
+   SYNTAX        INTEGER{
+                          vll(1),
+                          vllLocal(2),
+                          vpls(3)
+                       }
+
+AdminStatus ::= TEXTUAL-CONVENTION
+   STATUS        current
+   DESCRIPTION
+       "Administrative status of a given management entity."
+     SYNTAX        INTEGER{
+                              up(1),      -- ready to pass packets
+                              down(2),     -- can't pass packets
+                              testing(3)   -- in some test mode
+                        }
+
+ClassOfService ::= TEXTUAL-CONVENTION
+   STATUS        current
+   DESCRIPTION
+       "Class Of Service (COS) value of a given management entity.
+       Value 255 means that COS is not explicitly configured. Valid COS values
+       are between 0 and 7."
+   SYNTAX        Unsigned32(0..7 | 255)
+
+Layer2StateTC ::= TEXTUAL-CONVENTION
+   STATUS    current
+   DESCRIPTION
+     "Specifies the layer2 state a given interface can take.."
+   SYNTAX  INTEGER{  -- picked from Syntax of dot1dStpPortState
+                        disabled(1),
+                        blocking(2),
+                        listening(3),
+                        learning(4),
+                        preforwarding(5),
+                        forwarding(6)
+                 }
+
+--
+-- Top level components of this MIB.
+--
+
+  fdryMplsVpnNotifications   OBJECT IDENTIFIER ::= { fdryMplsL2VpnMIB 0 }
+  fdryMplsVllInfo   OBJECT IDENTIFIER ::= { fdryMplsL2VpnMIB 1 }  -- Includes VLL and VLL-Local
+  fdryMplsVplsInfo   OBJECT IDENTIFIER ::= { fdryMplsL2VpnMIB 2 }
+
+--
+-- L2 VPN VLL and VLL-Local Endpoint table
+--
+
+  fdryVllEndPointTable   OBJECT-TYPE
+     SYNTAX        SEQUENCE OF FdryVllEndPointEntry
+     MAX-ACCESS    not-accessible
+     STATUS        current
+     DESCRIPTION
+         "This table specifies information about the VLL and VLL-local endpoints which are not
+         available in the PW tables."
+     ::= { fdryMplsVllInfo 1 }
+
+  fdryVllEndPointEntry   OBJECT-TYPE
+     SYNTAX        FdryVllEndPointEntry
+     MAX-ACCESS    not-accessible
+     STATUS        current
+     DESCRIPTION
+          "A row in this table represents a VLL or VLL-local end point for a
+          pseudo-wire (PW) virtual connection across a packet network.
+          For a VLL, we would have one instance of this table for a given PW.
+          For a VLL-local, there would be two instances of this table for a given PW.
+          It is indexed by fdryVllEndPointServiceType, pwIndex, and pwEnetPwInstance.
+          The pwIndex is the index of pwTable, and {pwIndex, pwEnetPwInstance} together
+          provides an instance in the pwEnetTable.
+           A row can be created by an operator command after having created a row
+           in the pwTable and pwEnetTable.
+           1) Objects MUST NOT be changed after row activation.
+           2) Objects MAY be changed when the PW is
+           defined as not active. A change of these objects involves
+           re-signaling of the PW or it might be traffic affecting.
+           End point not active is defined as one of the following
+           conditions:
+                  a) The pwRowStatus is notInService(2).
+                  b) The pwRowStatus is notReady(3).
+                  c) The pwAdminStatus is down(2).
+           "
+     INDEX  {fdryVllEndPointServiceType, pwIndex, pwEnetPwInstance}
+            ::= { fdryVllEndPointTable 1 }
+
+  FdryVllEndPointEntry ::= SEQUENCE {
+        fdryVllEndPointServiceType           MplsServiceType ,
+        fdryVllEndPointVlanTagMode               VlanTagMode,
+        fdryVllEndPointClassOfService        ClassOfService,
+        fdryVllEndPointInHCPkts              Counter64,
+        fdryVllEndPointOutHCPkts              Counter64,
+        fdryVllEndPointAdminStatus           AdminStatus,
+        fdryVllEndPointOperStatus           PwOperStatusTC,
+        fdryVllEndPointRowStatus             RowStatus,
+        fdryVllEndPointInnerVlanId          PwVlanCfg,
+        fdryVllEndPointInHCOctets           Counter64,
+        fdryVllEndPointOutHCOctets         Counter64
+     }
+
+  fdryVllEndPointServiceType OBJECT-TYPE
+     SYNTAX        MplsServiceType
+     MAX-ACCESS    not-accessible
+     STATUS        current
+     DESCRIPTION
+         "A service type indicating VLL or VLL-local service for this endpoint.
+         The value vpls(3) is not used in this table.
+         "
+     ::= { fdryVllEndPointEntry 1 }
+
+  fdryVllEndPointVlanTagMode OBJECT-TYPE
+     SYNTAX        VlanTagMode
+     MAX-ACCESS    read-create
+     STATUS        current
+     DESCRIPTION
+         "This value indicates the vlan mode for this endpoint. The values,
+         dual(3) and other(4) is not used in this table.
+         "
+     ::= { fdryVllEndPointEntry 2 }
+
+  fdryVllEndPointClassOfService OBJECT-TYPE
+     SYNTAX        ClassOfService
+     MAX-ACCESS    read-create
+     STATUS        current
+     DESCRIPTION
+         "This value indicates the Class Of Service for this endpoint.
+         For VLL, this value is used to select the appropriate tunnel
+         whose COS value is either same, or almost approaching this value.
+         For VLL-local, this value is applied to the ingress packet of an endpoint
+         "
+     DEFVAL {0}
+     ::= { fdryVllEndPointEntry 3 }
+
+  fdryVllEndPointInHCPkts OBJECT-TYPE
+     SYNTAX        Counter64
+     MAX-ACCESS    read-only
+     STATUS        current
+     DESCRIPTION
+         "This value indicates the number of packets ingressing into this endpoint.
+           This counter is not supported in CES/CER platform.
+         "
+     ::= { fdryVllEndPointEntry 4 }
+
+  fdryVllEndPointOutHCPkts OBJECT-TYPE
+     SYNTAX        Counter64
+     MAX-ACCESS    read-only
+     STATUS        current
+     DESCRIPTION
+         "This value indicates the number of packets egressing out from this endpoint.
+         For VLL-local, this value could be the fdryVllEndPointInHCPkts of the other endpoint
+         of this VLL instance. But since rate limit could be applied to the incoming packet,
+         the count value will not be accurate. Due to this, the value will be 0 for VLL-local.
+           This counter is not supported in CES/CER platform.
+         "
+     ::= { fdryVllEndPointEntry 5 }
+
+  fdryVllEndPointAdminStatus OBJECT-TYPE
+     SYNTAX        AdminStatus
+     MAX-ACCESS    read-create
+     STATUS        current
+     DESCRIPTION
+         "The desired administrative status of this endpoint. This object MAY
+          be set at any time.
+         "
+     ::= { fdryVllEndPointEntry 6 }
+
+  fdryVllEndPointOperStatus OBJECT-TYPE
+     SYNTAX        PwOperStatusTC
+     MAX-ACCESS    read-only
+     STATUS        current
+     DESCRIPTION
+         "This object indicates the operational status of this endpoint.
+         Only values up(1), down(2) are used in this table
+         "
+     ::= { fdryVllEndPointEntry 7 }
+
+  fdryVllEndPointRowStatus OBJECT-TYPE
+     SYNTAX        RowStatus
+     MAX-ACCESS    read-create
+     STATUS        current
+     DESCRIPTION
+       "This variable is used to create, modify, and/or
+        delete a row in this table. When a row in this
+        table is in active(1) state, no objects in that row
+        can be modified except this object, and the fdryVllEndPointAdminStatus.
+        "
+     ::= { fdryVllEndPointEntry 8 }
+
+fdryVllEndPointInnerVlanId OBJECT-TYPE
+     SYNTAX        PwVlanCfg
+     MAX-ACCESS    read-create
+     STATUS        current
+     DESCRIPTION
+         "This value indicates the inner vlan id for this endpoint.
+          Returns 0 if not configured or is not supported.
+         "
+     DEFVAL { 0 }
+     ::= { fdryVllEndPointEntry 9 }
+
+  fdryVllEndPointInHCOctets OBJECT-TYPE
+     SYNTAX        Counter64
+     MAX-ACCESS    read-only
+     STATUS        current
+     DESCRIPTION
+         "This value indicates the number of octets ingressing into this endpoint
+         from a Customer Edge (CE) device.
+           This counter is supported in CES/CER platform.
+         "
+     ::= { fdryVllEndPointEntry 10 }
+
+  fdryVllEndPointOutHCOctets OBJECT-TYPE
+     SYNTAX        Counter64
+     MAX-ACCESS    read-only
+     STATUS        current
+     DESCRIPTION
+         "This value indicates the number of octets egressing out from this endpoint towards
+         the Customer Edge (CE) device.
+          This counter is not supported in CES/CER platform.
+           Within CES/CER, any packet coming in from the tunnel will have its MPLS header as part of the octet count.
+         "
+     ::= { fdryVllEndPointEntry 11 }
+
+
+--
+-- L2 VPN VLL and VLL-Local Endpoint Extended Statistics table
+--
+
+  brcdVllEndptVlanExtStatsTable OBJECT-TYPE
+    SYNTAX  SEQUENCE OF BrcdVllEndptVlanExtStatsEntry
+    MAX-ACCESS  not-accessible
+    STATUS  current
+    DESCRIPTION
+        "This table contains the VLAN extended statistics
+         for VLL endpoints."
+    ::= { fdryMplsVllInfo 2 }
+
+  brcdVllEndptVlanExtStatsEntry OBJECT-TYPE
+    SYNTAX  BrcdVllEndptVlanExtStatsEntry
+    MAX-ACCESS  not-accessible
+    STATUS  current
+    DESCRIPTION
+        "A row in this table represents a VLAN extended statistics
+        accounting entry of a VLL endpoint."
+    INDEX  { fdryVllEndPointServiceType,
+                  pwIndex,
+                  pwEnetPwInstance,
+                  brcdVllEndptVlanExtStatsPriorityId
+                }
+    ::= { brcdVllEndptVlanExtStatsTable 1 }
+
+  BrcdVllEndptVlanExtStatsEntry ::= SEQUENCE {
+        brcdVllEndptVlanExtStatsPriorityId
+            PortPriorityTC,
+        brcdVllEndptVlanExtStatsInPkts
+            Counter64,
+        brcdVllEndptVlanExtStatsOutPkts
+            Counter64,
+        brcdVllEndptVlanExtStatsInOctets
+            Counter64,
+        brcdVllEndptVlanExtStatsOutOctets
+            Counter64
+      }
+
+  brcdVllEndptVlanExtStatsPriorityId OBJECT-TYPE
+    SYNTAX  PortPriorityTC
+    MAX-ACCESS  not-accessible
+    STATUS  current
+    DESCRIPTION
+        "Identifies the port QOS priority.
+         The values 1 through 8 internally maps to priorities 0 through 7.
+         The value 128 indicates that priority-level accounting is not enabled"
+    ::= { brcdVllEndptVlanExtStatsEntry 1 }
+
+  brcdVllEndptVlanExtStatsInPkts OBJECT-TYPE
+    SYNTAX  Counter64
+    MAX-ACCESS  read-only
+    STATUS  current
+    DESCRIPTION
+        "The number of valid frames received by this endpoint
+         from the Customer Edge (CE)."
+    ::= { brcdVllEndptVlanExtStatsEntry 2 }
+
+  brcdVllEndptVlanExtStatsOutPkts OBJECT-TYPE
+    SYNTAX  Counter64
+    MAX-ACCESS  read-only
+    STATUS  current
+    DESCRIPTION
+        "The number of valid frames transmitted by this endpoint
+         to the Customer Edge (CE)."
+    ::= { brcdVllEndptVlanExtStatsEntry 3 }
+
+  brcdVllEndptVlanExtStatsInOctets OBJECT-TYPE
+    SYNTAX  Counter64
+    MAX-ACCESS  read-only
+    STATUS  current
+    DESCRIPTION
+        "The bytes count received by this endpoint from the Customer Edge (CE)."
+    ::= { brcdVllEndptVlanExtStatsEntry 4 }
+
+  brcdVllEndptVlanExtStatsOutOctets OBJECT-TYPE
+    SYNTAX  Counter64
+    MAX-ACCESS  read-only
+    STATUS  current
+    DESCRIPTION
+        "The bytes count transmitted by this endpoint to
+        the Customer Edge (CE)."
+    ::= { brcdVllEndptVlanExtStatsEntry 5 }
+
+
+-- Deprecated table fdryVplsEndPointTable
+
+  fdryVplsEndPointTable   OBJECT-TYPE
+     SYNTAX        SEQUENCE OF FdryVplsEndPointEntry
+     MAX-ACCESS    not-accessible
+     STATUS        deprecated
+     DESCRIPTION
+         "This table specifies information about the VPLS endpoints which are not
+         available in the PW mib, or VPLS draft mib."
+     ::= { fdryMplsVplsInfo 1 }
+
+  fdryVplsEndPointEntry   OBJECT-TYPE
+     SYNTAX        FdryVplsEndPointEntry
+     MAX-ACCESS    not-accessible
+     STATUS        deprecated
+     DESCRIPTION
+          "A row in this table represents a VPLS end point for a
+          given VPLS instance. The VPLS instance is represented
+          by vplsConfigTable and fdryVplsTable.
+          For a given VPLS instance, there could be multiple instances
+          of rows within this table, each describing one endpoint.
+          For a given endpoint, there will be one VPLS instance.
+          A given endpoint is represented by vplsConfigIndex (VPLS instance),
+          vlan id, and ifIndex of the physical port which is acting as an endpoint.
+          This allows a tagged port to be associated with multiple VPLS instances.
+          An untagged port can only be associated with one VPLS instance.
+          Note that this table is kept independent of the PW tables to indicate
+          that endpoints terminate on the VPLS instance.
+          On the other side, a VPLS instance will have association with the PW MIB.
+          This table is indexed by vplsConfigIndex, fdryVplsEndPointPortVlan,
+          and fdryVplsEndPointIfIndex.
+           "
+     INDEX  {vplsConfigIndex, fdryVplsEndPointPortVlan, fdryVplsEndPointIfIndex}
+            ::= { fdryVplsEndPointTable 1 }
+
+  FdryVplsEndPointEntry ::= SEQUENCE {
+        fdryVplsEndPointPortVlan           PwVlanCfg ,
+        fdryVplsEndPointIfIndex            InterfaceIndex,
+        fdryVplsEndPointVlanTagMode        VlanTagMode,
+        fdryVplsEndPointOutHCPkts            Counter64,
+        fdryVplsEndPointState                INTEGER,
+        fdryVplsEndPointAdminStatus           AdminStatus,
+        fdryVplsEndPointOperStatus           PwOperStatusTC,
+        fdryVplsEndPointRowStatus             RowStatus,
+        fdryVplsEndPointInHCOctets           Counter64
+     }
+
+  fdryVplsEndPointPortVlan OBJECT-TYPE
+     SYNTAX        PwVlanCfg
+     MAX-ACCESS    not-accessible
+     STATUS        deprecated
+     DESCRIPTION
+         "This value specifies the VLAN id value of this endpoint.
+         "
+     ::= { fdryVplsEndPointEntry 1 }
+
+  fdryVplsEndPointIfIndex OBJECT-TYPE
+     SYNTAX        InterfaceIndex
+     MAX-ACCESS    not-accessible
+     STATUS        deprecated
+     DESCRIPTION
+         "This value specifies the ifIndex value of this endpoint.
+         "
+     ::= { fdryVplsEndPointEntry 2 }
+
+  fdryVplsEndPointVlanTagMode OBJECT-TYPE
+     SYNTAX        VlanTagMode
+     MAX-ACCESS    read-create
+     STATUS        deprecated
+     DESCRIPTION
+         "This value indicates the vlan mode for this endpoint. The values,
+         dual(3) and other(4) is not used in this table.
+         "
+     ::= { fdryVplsEndPointEntry 3 }
+
+  fdryVplsEndPointOutHCPkts OBJECT-TYPE
+     SYNTAX        Counter64
+     MAX-ACCESS    read-only
+     STATUS        deprecated
+     DESCRIPTION
+         "This counter indicates the number of packets egressing
+         out from this endpoint towards the Customer Edge (CE).
+         This value counts packets coming from multiple pseudo-wires
+         towards the endpoint, as well as locally switched packets
+         between other endpoints to this endpoint, all belonging
+         to the same VPLS instance.
+           The value gives count of known unicast packets only.
+         Unknown unicast and broadcast packets are not counted.
+           This object is not supported in CES/CER.
+         "
+     ::= { fdryVplsEndPointEntry 4 }
+
+  fdryVplsEndPointState OBJECT-TYPE
+       SYNTAX      INTEGER { -- picked from Syntax of dot1dStpPortState
+                            disabled(1),
+                            blocking(2),
+                            forwarding(5)
+                   }
+     MAX-ACCESS    read-only
+     STATUS        deprecated
+     DESCRIPTION
+         "A L2 state of this VPLS endpoint.
+         "
+     ::= { fdryVplsEndPointEntry 5 }
+
+  fdryVplsEndPointAdminStatus OBJECT-TYPE
+     SYNTAX        AdminStatus
+     MAX-ACCESS    read-create
+     STATUS        deprecated
+     DESCRIPTION
+         "The desired administrative status of this endpoint. This object MAY
+          be set at any time.
+         "
+     ::= { fdryVplsEndPointEntry 6 }
+
+  fdryVplsEndPointOperStatus OBJECT-TYPE
+     SYNTAX        PwOperStatusTC
+     MAX-ACCESS    read-only
+     STATUS        deprecated
+     DESCRIPTION
+         "This object indicates the operational status of this endpoint.
+         Only values up(1), down(2) are used in this table
+         "
+     ::= { fdryVplsEndPointEntry 7 }
+
+  fdryVplsEndPointRowStatus OBJECT-TYPE
+     SYNTAX        RowStatus
+     MAX-ACCESS    read-create
+     STATUS        deprecated
+     DESCRIPTION
+       "This variable is used to create, modify, and/or
+        delete a row in this table. When a row in this
+        table is in active(1) state, no objects in that row
+        can be modified except this object and the fdryVplsEndPointAdminStatus.
+         "
+     ::= { fdryVplsEndPointEntry 8 }
+
+  fdryVplsEndPointInHCOctets OBJECT-TYPE
+     SYNTAX        Counter64
+     MAX-ACCESS    read-only
+     STATUS        deprecated
+     DESCRIPTION
+         "This counter indicates the number of octets ingressing
+         into this endpoint from the Customer Edge (CE).
+           This object is supported in CES/CER only.
+         "
+     ::= { fdryVplsEndPointEntry 9 }
+
+--
+-- L2 VPN VPLS Endpoint table
+--
+  fdryVplsEndPoint2Table   OBJECT-TYPE
+     SYNTAX        SEQUENCE OF FdryVplsEndPoint2Entry
+     MAX-ACCESS    not-accessible
+     STATUS        current
+     DESCRIPTION
+         "This table specifies information about the VPLS endpoints which are not
+         available in the PW mib, or VPLS draft mib.
+           This table deprecates fdryVplsEndPointTable, as inner VLAN and ISID
+         has been added as index to this table."
+     ::= { fdryMplsVplsInfo 3 }
+
+  fdryVplsEndPoint2Entry   OBJECT-TYPE
+     SYNTAX        FdryVplsEndPoint2Entry
+     MAX-ACCESS    not-accessible
+     STATUS        current
+     DESCRIPTION
+          "A row in this table represents a VPLS end point for a
+          given VPLS instance. The VPLS instance is represented
+          by vplsConfigTable and fdryVplsTable.
+          For a given VPLS instance, there could be multiple instances
+          of rows within this table, each describing one endpoint.
+          For a given endpoint, there will be one VPLS instance.
+          A given endpoint is represented by vplsConfigIndex (VPLS instance),
+          vlan id, inner-id (inner VLAN or ISID),and ifIndex of the physical port which is acting as an endpoint.
+          This allows a tagged port to be associated with multiple VPLS instances, and also many inner VLAN or ISID
+          to be associated with a tagged port (outer VLAN tag)
+          An untagged port can only be associated with one VPLS instance.
+          Note that this table is kept independent of the PW tables to indicate
+          that endpoints terminate on the VPLS instance.
+          On the other side, a VPLS instance will have association with the PW MIB.
+          This table is indexed by vplsConfigIndex, fdryVplsEndPointPortVlan,
+          and fdryVplsEndPointIfIndex.
+           "
+     INDEX  {vplsConfigIndex,
+             fdryVplsEndPoint2VlanId,
+             fdryVplsEndPoint2InnerTagType, --inner vlan or ISID
+             fdryVplsEndPoint2InnerTag,
+             fdryVplsEndPoint2IfIndex}
+            ::= { fdryVplsEndPoint2Table 1 }
+
+  FdryVplsEndPoint2Entry ::= SEQUENCE {
+        fdryVplsEndPoint2VlanId           PwVlanCfg ,
+        fdryVplsEndPoint2InnerTagType        INTEGER,
+        fdryVplsEndPoint2InnerTag            Unsigned32,
+        fdryVplsEndPoint2IfIndex            InterfaceIndex,
+        fdryVplsEndPoint2VlanTagMode        VlanTagMode,
+        fdryVplsEndPoint2InHCOctets           Counter64,
+        fdryVplsEndPoint2Layer2State          Layer2StateTC,
+        fdryVplsEndPoint2OperStatus           PwOperStatusTC,
+        fdryVplsEndPoint2RowStatus             RowStatus
+     }
+
+  fdryVplsEndPoint2VlanId OBJECT-TYPE
+     SYNTAX        PwVlanCfg
+     MAX-ACCESS    not-accessible
+     STATUS        current
+     DESCRIPTION
+         "This value specifies the VLAN id value of this endpoint.
+         "
+     ::= { fdryVplsEndPoint2Entry 1 }
+
+  fdryVplsEndPoint2InnerTagType OBJECT-TYPE
+     SYNTAX        INTEGER {invalid(1),innerVlan(2), isid(3)}
+     MAX-ACCESS    not-accessible
+     STATUS        current
+     DESCRIPTION
+         "This value indicates the inner id for this endpoint.
+         If no inner tag is specified, value invalid(1) is returned.
+         "
+     ::= { fdryVplsEndPoint2Entry 2 }
+
+  fdryVplsEndPoint2InnerTag OBJECT-TYPE
+     SYNTAX        Unsigned32
+     MAX-ACCESS    not-accessible
+     STATUS        current
+     DESCRIPTION
+         "This value indicates the inner tag for this endpoint.
+          If the index fdryVplsEndPoint2InnerTagType has
+          value isid(3), then this object will have the
+          ISID value for that endpoint. Valid ISID value
+          is between 256 (0x100) and 16777214 (0xFFFFFE).
+         If no inner tag is specified, value 0 is returned.
+         "
+     ::= { fdryVplsEndPoint2Entry 3 }
+
+  fdryVplsEndPoint2IfIndex OBJECT-TYPE
+     SYNTAX        InterfaceIndex
+     MAX-ACCESS    not-accessible
+     STATUS        current
+     DESCRIPTION
+         "This value specifies the ifIndex value of this endpoint.
+         "
+     ::= { fdryVplsEndPoint2Entry 4 }
+
+  fdryVplsEndPoint2VlanTagMode OBJECT-TYPE
+     SYNTAX        VlanTagMode
+     MAX-ACCESS    read-create
+     STATUS        current
+     DESCRIPTION
+         "This value indicates the vlan mode for this endpoint. The values,
+         dual(3) and other(4) is not used in this table.
+         "
+     ::= { fdryVplsEndPoint2Entry 5 }
+
+  fdryVplsEndPoint2InHCOctets OBJECT-TYPE
+     SYNTAX        Counter64
+     MAX-ACCESS    read-only
+     STATUS        current
+     DESCRIPTION
+         "This counter indicates the number of octets ingressing
+         into this endpoint from the Customer Edge (CE).
+           This object is supported in CES/CER only.
+         "
+     ::= { fdryVplsEndPoint2Entry 6 }
+
+  fdryVplsEndPoint2Layer2State OBJECT-TYPE
+     SYNTAX      Layer2StateTC
+     MAX-ACCESS    read-only
+     STATUS        current
+     DESCRIPTION
+         "The L2 state of this VPLS endpoint.
+         "
+     ::= { fdryVplsEndPoint2Entry 7 }
+
+  fdryVplsEndPoint2OperStatus OBJECT-TYPE
+     SYNTAX        PwOperStatusTC
+     MAX-ACCESS    read-only
+     STATUS        current
+     DESCRIPTION
+         "This object indicates the operational status of this endpoint.
+         Only values up(1), down(2) are used in this table
+         "
+     ::= { fdryVplsEndPoint2Entry 8 }
+
+  fdryVplsEndPoint2RowStatus OBJECT-TYPE
+     SYNTAX        RowStatus
+     MAX-ACCESS    read-create
+     STATUS        current
+     DESCRIPTION
+       "This variable is used to create, modify, and/or
+        delete a row in this table. When a row in this
+        table is in active(1) state, no objects in that row
+        can be modified except this object.
+         "
+     ::= { fdryVplsEndPoint2Entry 9 }
+
+
+
+--
+-- L2 VPN VPLS Instance Table
+--
+
+  fdryVplsTable   OBJECT-TYPE
+     SYNTAX        SEQUENCE OF FdryVplsEntry
+     MAX-ACCESS    not-accessible
+     STATUS        current
+     DESCRIPTION
+         "This table specifies additional information about the VPLS instance configuration
+          which is not available in the VplsConfigTable. Some of these
+          objects are configuration specific, some are commands specific
+          to that VPLS instance."
+     ::= { fdryMplsVplsInfo 2 }
+
+  fdryVplsEntry   OBJECT-TYPE
+     SYNTAX        FdryVplsEntry
+     MAX-ACCESS    not-accessible
+     STATUS        current
+     DESCRIPTION
+          "A row in this table represents a VPLS instance. It augments
+          the vplsConfigTable in the VPLS draft mib.
+           "
+     AUGMENTS    { vplsConfigEntry }
+            ::= { fdryVplsTable 1 }
+
+  FdryVplsEntry ::= SEQUENCE {
+        fdryVplsClassOfService           ClassOfService ,
+        fdryVplsMaxMacLearned            Unsigned32,
+        fdryVplsClearMac        TruthValue,
+        fdryVplsVcId            Unsigned32
+     }
+
+  fdryVplsClassOfService OBJECT-TYPE
+     SYNTAX        ClassOfService
+     MAX-ACCESS    read-create
+     STATUS        current
+     DESCRIPTION
+         "This value indicates the Class Of Service for this VPLS instance.
+         This value is used to select the appropriate tunnel
+         whose COS value is either same, or almost approaching this value.
+         "
+     DEFVAL {0}
+     ::= { fdryVplsEntry 1 }
+
+  fdryVplsMaxMacLearned OBJECT-TYPE
+     SYNTAX        Unsigned32
+     MAX-ACCESS    read-only
+     STATUS        current
+     DESCRIPTION
+         "This value indicates the maximum number of MAC addresses
+         that can be learned by this VPLS instance.
+         "
+     ::= { fdryVplsEntry 2}
+
+  fdryVplsClearMac OBJECT-TYPE
+     SYNTAX        TruthValue
+     MAX-ACCESS    read-create
+     STATUS        current
+     DESCRIPTION
+         "The Set value of TRUE tells the system to clear all the MAC addresses
+         learned by this VPLS instance. Setting value of FALSE will return an error.
+         During read operations, value FALSE will be returned at all times.
+         "
+     ::= { fdryVplsEntry 3}
+
+  fdryVplsVcId OBJECT-TYPE
+     SYNTAX        Unsigned32
+     MAX-ACCESS    read-only
+     STATUS        current
+     DESCRIPTION
+         "The VPLS Instance ID of a given VPLS session.
+         "
+     ::= { fdryVplsEntry 4}
+
+--
+-- L2 VPN VPLS Endpoint Extended Statistics table
+--
+
+  brcdVplsEndptVlanExtStatsTable OBJECT-TYPE
+    SYNTAX  SEQUENCE OF BrcdVplsEndptVlanExtStatsEntry
+    MAX-ACCESS  not-accessible
+    STATUS  current
+    DESCRIPTION
+        "This table contains the VLAN extended statistics for VPLS endpoints."
+    ::= { fdryMplsVplsInfo 4 }
+
+  brcdVplsEndptVlanExtStatsEntry OBJECT-TYPE
+    SYNTAX  BrcdVplsEndptVlanExtStatsEntry
+    MAX-ACCESS  not-accessible
+    STATUS  current
+    DESCRIPTION
+        "A row in this table represents a VLAN extended statistics
+         accounting entry of a VPLS endpoint."
+    INDEX  {vplsConfigIndex,
+                 fdryVplsEndPoint2VlanId,
+                 fdryVplsEndPoint2InnerTagType,
+                 fdryVplsEndPoint2InnerTag,
+                 fdryVplsEndPoint2IfIndex,
+                 brcdVplsEndptVlanExtStatsPriorityId }
+::= { brcdVplsEndptVlanExtStatsTable 1 }
+
+  BrcdVplsEndptVlanExtStatsEntry ::= SEQUENCE {
+      brcdVplsEndptVlanExtStatsPriorityId
+          PortPriorityTC,
+      brcdVplsEndptVlanExtStatsInPkts
+          Counter64,
+      brcdVplsEndptVlanExtStatsOutPkts
+          Counter64,
+      brcdVplsEndptVlanExtStatsInOctets
+          Counter64,
+      brcdVplsEndptVlanExtStatsOutOctets
+          Counter64
+    }
+
+  brcdVplsEndptVlanExtStatsPriorityId OBJECT-TYPE
+    SYNTAX  PortPriorityTC
+    MAX-ACCESS  not-accessible
+    STATUS  current
+    DESCRIPTION
+        "Identifies the port QOS priority.
+         The values 1 through 8 internally maps to priorities 0 through 7.
+         The value 128 indicates that priority-level accounting is not enabled"
+    ::= { brcdVplsEndptVlanExtStatsEntry 1 }
+
+  brcdVplsEndptVlanExtStatsInPkts OBJECT-TYPE
+    SYNTAX  Counter64
+    MAX-ACCESS  read-only
+    STATUS  current
+    DESCRIPTION
+        "The number of valid frames received by this endpoint from
+         the Customer Edge (CE)."
+    ::= { brcdVplsEndptVlanExtStatsEntry 2 }
+
+  brcdVplsEndptVlanExtStatsOutPkts OBJECT-TYPE
+    SYNTAX  Counter64
+    MAX-ACCESS  read-only
+    STATUS  current
+    DESCRIPTION
+        "The number of valid frames transmitted by this endpoint to
+         the Customer Edge (CE)."
+    ::= { brcdVplsEndptVlanExtStatsEntry 3 }
+
+  brcdVplsEndptVlanExtStatsInOctets OBJECT-TYPE
+    SYNTAX  Counter64
+    MAX-ACCESS  read-only
+    STATUS  current
+    DESCRIPTION
+        "The bytes count received by this endpoint from
+         the Customer Edge (CE)."
+    ::= { brcdVplsEndptVlanExtStatsEntry 4 }
+
+  brcdVplsEndptVlanExtStatsOutOctets OBJECT-TYPE
+    SYNTAX  Counter64
+    MAX-ACCESS  read-only
+    STATUS  current
+    DESCRIPTION
+        "The bytes count transmitted by this endpoint to
+         the Customer Edge (CE)."
+   ::= { brcdVplsEndptVlanExtStatsEntry 5 }
+
+
+--
+  -- L2 VPN Service Notifications
+--
+
+  fdryVplsCreated NOTIFICATION-TYPE
+      OBJECTS {
+          vplsConfigName, --VPLS name
+          fdryVplsVcId --VPLS VC ID
+      }
+      STATUS          current
+      DESCRIPTION
+           "This notification is generated when an entry is created in
+            fdryVplsTable, indicating creation of a new VPLS instance.
+              This notification is not generated during system boot up time."
+      --#TYPE "Foundry Trap: MPLS VPLS Instance Created"
+      --#SUMMARY "VPLS %s (VC ID %d) has been created."
+      --#ARGUMENTS { 0, 1 }
+      --#SEVERITY INFORMATIONAL
+      --#STATE OPERATIONAL
+      ::= { fdryMplsVpnNotifications 1 }
+
+  fdryVplsDeleted NOTIFICATION-TYPE
+      OBJECTS {
+          vplsConfigName, --VPLS name
+          fdryVplsVcId --VPLS VC ID
+      }
+      STATUS          current
+      DESCRIPTION
+           "This notification is generated when one entry in the
+            fdryVplsTable have been marked for deletion, indicating
+           deletion of an existing VPLS instance."
+      --#TYPE "Foundry Trap: MPLS VPLS Instance Deleted"
+      --#SUMMARY "VPLS %s (VC ID %d) has been deleted."
+      --#ARGUMENTS { 0, 1 }
+      --#SEVERITY INFORMATIONAL
+      --#STATE OPERATIONAL
+      ::= { fdryMplsVpnNotifications 2 }
+
+  fdryPwCreated NOTIFICATION-TYPE
+      OBJECTS {
+          fdryPwServiceType,
+          pwName, --VLL or VLL-Local name
+          pwID       --VLL VC ID, value 0 for VLL-Local
+      }
+      STATUS          current
+      DESCRIPTION
+           "This notification is generated when an instance of VLL or VLL-Local
+           pseudo-wire entry is created in the pwTable.
+             The varbind fdryPwServiceType has the service type which
+           originated this notification.
+             This notification is not used for VPLS service.
+             This notification is not generated during system boot up time"
+      --#TYPE "Foundry Trap: MPLS L2VPN Instance Created"
+      --#SUMMARY "L2VPN %d (1=VLL, 2=VLL-Local) Instance %s (VC ID %d) has been created."
+      --#ARGUMENTS { 0, 1, 2 }
+      --#SEVERITY INFORMATIONAL
+      --#STATE OPERATIONAL
+      ::= { fdryMplsVpnNotifications 3 }
+
+END
+
+

mibs/FDRY-POE-MIB

@@ -0,0 +1,325 @@
+FDRY-POE-MIB DEFINITIONS ::= BEGIN
+
+IMPORTS
+	MODULE-IDENTITY, OBJECT-TYPE,
+			Integer32, Unsigned32	   	FROM SNMPv2-SMI	  			-- [RFC2578]
+	DisplayString		 				FROM SNMPv2-TC 		 		-- [RFC2579]
+	InterfaceIndex						FROM IF-MIB
+	snAgentSys	 						FROM FOUNDRY-SN-ROOT-MIB
+	;
+
+snAgentPoe MODULE-IDENTITY
+    LAST-UPDATED "201006020000Z"  -- 04 June 2010
+    ORGANIZATION "Brocade Communications Systems, Inc."
+    CONTACT-INFO
+             "Technical Support Center
+              130 Holger Way,
+              San Jose, CA  95134
+              Email:  ipsupport@brocade.com
+              Phone: 1-800-752-8061
+              URL:  www.brocade.com"
+    DESCRIPTION
+	      "The Brocade proprietary MIB module for Power Over Ethernet(PoE)
+		It has PoE port and module configuring information.
+
+              Copyright 1996-2010 Brocade Communications Systems, Inc.
+              All rights reserved.
+              This Brocade Communications Systems SNMP Management Information Base Specification
+              embodies Brocade Communications Systems' confidential and proprietary
+              intellectual property. Brocade Communications Systems retains all
+              title and ownership in the Specification, including any revisions.
+
+              This Specification is supplied AS IS, and Brocade Communications Systems makes
+              no warranty, either express or implied, as to the use,
+              operation, condition, or performance of the specification, and any unintended
+              consequence it may on the user environment."
+
+    REVISION        "201006020000Z"  -- 04 June 2010
+    DESCRIPTION
+        "Changed the ORGANIZATION, CONTACT-INFO and DESCRIPTION fields."
+
+    REVISION     "200909300000Z" -- September 30, 2009
+    DESCRIPTION	"Changed INTEGER to Integer32"
+
+    REVISION 	"200904030000Z"  -- 3 April 2009
+    DESCRIPTION	"Initial version, snAgentPoePortTable which was in SNMPv1 written in SNMPv2-SMI."
+
+  ::= { snAgentSys 14 }
+
+-- Power Over Ethernet MIB Group
+
+snAgentPoeGbl  OBJECT IDENTIFIER ::= { snAgentPoe 1 }
+snAgentPoePort OBJECT IDENTIFIER ::= { snAgentPoe 2 }
+snAgentPoeModule OBJECT IDENTIFIER ::= { snAgentPoe 3 }
+snAgentPoeUnit OBJECT IDENTIFIER ::= { snAgentPoe 4 }
+
+
+-- Power Over Ethernet Global Objects
+
+snAgentPoeGblPowerCapacityTotal  OBJECT-TYPE
+	SYNTAX Unsigned32
+	MAX-ACCESS	read-only
+	STATUS	current
+	DESCRIPTION
+		"This object shows the total inline power capacity available in the device, measured in mWatts. "
+	::= { snAgentPoeGbl 1 }
+
+snAgentPoeGblPowerCapacityFree  OBJECT-TYPE
+	SYNTAX Unsigned32
+	MAX-ACCESS	read-only
+	STATUS	current
+	DESCRIPTION
+		"This object shows the inline power capacity currently available in the device which is unallocated, measured in mWatts."
+	::= { snAgentPoeGbl 2 }
+
+snAgentPoeGblPowerAllocationsRequestsHonored   OBJECT-TYPE
+	SYNTAX Unsigned32
+	MAX-ACCESS	read-only
+	STATUS	current
+	DESCRIPTION
+		"This object shows number of times the inline power allocations requests honored."
+	::= { snAgentPoeGbl 3}
+
+
+-- Power Over Ethernet Port Table
+
+snAgentPoePortTable       OBJECT-TYPE
+	SYNTAX	SEQUENCE OF SnAgentPoePortEntry
+	MAX-ACCESS	not-accessible
+	STATUS	current
+	DESCRIPTION
+		"A table of POE port information."
+	::= { snAgentPoePort 2 }
+
+snAgentPoePortEntry       OBJECT-TYPE
+	SYNTAX	SnAgentPoePortEntry
+	MAX-ACCESS	not-accessible
+	STATUS	current
+	DESCRIPTION
+		"A row in the POE port table."
+	INDEX	{ snAgentPoePortNumber }
+	::= { snAgentPoePortTable 1 }
+
+SnAgentPoePortEntry ::= SEQUENCE {
+	snAgentPoePortNumber
+		InterfaceIndex,
+	snAgentPoePortControl
+		INTEGER,
+	snAgentPoePortWattage
+		Integer32,
+	snAgentPoePortClass
+		Integer32,
+	snAgentPoePortPriority
+		INTEGER,
+	snAgentPoePortConsumed
+		Integer32,
+	snAgentPoePortType
+		DisplayString
+	}
+
+snAgentPoePortNumber OBJECT-TYPE
+    SYNTAX  InterfaceIndex
+	MAX-ACCESS	read-only
+	STATUS	current
+	DESCRIPTION
+		"The port number in ifIndex value."
+	::= { snAgentPoePortEntry 1 }
+
+snAgentPoePortControl OBJECT-TYPE
+	SYNTAX	INTEGER {
+              other(1),
+              disable(2),
+              enable(3),
+              enableLegacyDevice(4)
+            }
+	MAX-ACCESS  read-create
+	STATUS	current
+	DESCRIPTION
+		"Control inline power on/off to a port. If a port does not
+		have inline power capability, reading this object returns
+		'other(1)'."
+	::= { snAgentPoePortEntry 2 }
+
+snAgentPoePortWattage OBJECT-TYPE
+	SYNTAX	Integer32
+	MAX-ACCESS  read-create
+	STATUS	current
+    DESCRIPTION
+		"Adjust the inline power wattage. Valid value between 1000
+		to 15400(IEEE802_3AF)/30000(IEEE802_3AT). Each unit is milliwatts. This object can only be
+		set after snSwIfInLinePowerControl has been set to 'enable(3)'
+		or 'enableLegacyDevice(4)'. If a port does not have inline
+		power capability, reading this object returns undefined value."
+    ::= { snAgentPoePortEntry 3 }
+
+snAgentPoePortClass OBJECT-TYPE
+	SYNTAX	Integer32
+	MAX-ACCESS  read-create
+	STATUS	current
+    DESCRIPTION
+		"Adjust the inline power class. Valid value between 0 to 3(IEEE802_3AF)/4(IEEE802_3AT).
+		This object can only be set after snSwIfInLinePowerControl
+		has been set to 'enable(3)' or 'enableLegacyDevice(4)'. If
+		a port does not have inline power capability, reading this
+		object returns undefined value."
+    ::= { snAgentPoePortEntry 4 }
+
+snAgentPoePortPriority OBJECT-TYPE
+	SYNTAX	INTEGER	{
+              invalid(0),
+              critical(1),
+              high(2),
+              low(3),
+              medium(4),
+              other(5)
+            }
+	MAX-ACCESS  read-create
+	STATUS	current
+	DESCRIPTION
+		"Inline power allocation priority for the power device
+		 0- Not a POE port, 1- Critical, 2- High, 3- Low,
+		 4- Medium, 5- other."
+	::= { snAgentPoePortEntry 5 }
+
+snAgentPoePortConsumed OBJECT-TYPE
+	SYNTAX	Integer32
+	MAX-ACCESS	read-only
+	STATUS	current
+	DESCRIPTION
+		"Inline power consumed by the port. Each unit is milliwatts."
+	::= { snAgentPoePortEntry 6 }
+
+snAgentPoePortType OBJECT-TYPE
+	SYNTAX	DisplayString
+	MAX-ACCESS	read-only
+	STATUS	current
+	DESCRIPTION
+		"Inline Power device type	802.3af, 802.3at or Legacy device."
+	::= { snAgentPoePortEntry 7 }
+
+
+-- Power Over Module Table
+
+snAgentPoeModuleTable       OBJECT-TYPE
+	SYNTAX	SEQUENCE OF SnAgentPoeModuleEntry
+	MAX-ACCESS	not-accessible
+	STATUS	current
+	DESCRIPTION
+		"A table of POE Module configuration."
+	::= { snAgentPoeModule 1 }
+
+snAgentPoeModuleEntry       OBJECT-TYPE
+	SYNTAX	SnAgentPoeModuleEntry
+	MAX-ACCESS	not-accessible
+	STATUS	current
+	DESCRIPTION
+		"A row in the POE Module table."
+	INDEX	{ snAgentPoeModuleNumber }
+	::= { snAgentPoeModuleTable 1 }
+
+SnAgentPoeModuleEntry ::= SEQUENCE {
+	snAgentPoeModuleNumber
+		Unsigned32,
+	snAgentPoeModuleBudget
+		Unsigned32,
+	snAgentPoeModuleMaxPDTypeSupport
+		INTEGER
+	}
+
+snAgentPoeModuleNumber OBJECT-TYPE
+    SYNTAX  Unsigned32
+	MAX-ACCESS	read-only
+	STATUS	current
+	DESCRIPTION
+		"This objects talks about POE module number."
+	::= { snAgentPoeModuleEntry 1 }
+
+snAgentPoeModuleBudget OBJECT-TYPE
+	SYNTAX	Unsigned32
+	MAX-ACCESS  read-create
+	STATUS	current
+    DESCRIPTION
+		"This objects talks about module power budget in watts."
+    ::= { snAgentPoeModuleEntry 2 }
+
+snAgentPoeModuleMaxPDTypeSupport  OBJECT-TYPE
+	SYNTAX	INTEGER	{
+              ieee802dot3af(0),
+              ieee802dot3at(1)
+            }
+	MAX-ACCESS  read-only
+	STATUS	current
+    DESCRIPTION
+		"This object talks about the POE module type which is capable to support Power Device (PD) type
+		ieee802.3af or ieee802.3at(also called POE plus)type. Module which support ieee802.3at can also
+		support ieee802.3af but reverse is not true."
+
+    ::= { snAgentPoeModuleEntry 3 }
+
+
+
+-- Power Over Unit Table (stacking system)
+
+snAgentPoeUnitTable       OBJECT-TYPE
+	SYNTAX	SEQUENCE OF SnAgentPoeUnitEntry
+	MAX-ACCESS	not-accessible
+	STATUS	current
+	DESCRIPTION
+		"A table of POE informaion for each unit. Only the unit
+		that has POE capability appears in a table row"
+	::= { snAgentPoeUnit 1 }
+
+snAgentPoeUnitEntry       OBJECT-TYPE
+	SYNTAX	SnAgentPoeUnitEntry
+	MAX-ACCESS	not-accessible
+	STATUS	current
+	DESCRIPTION
+		"A row in the POE Unit table."
+	INDEX	{ snAgentPoeUnitIndex }
+	::= { snAgentPoeUnitTable 1 }
+
+SnAgentPoeUnitEntry ::= SEQUENCE {
+	snAgentPoeUnitIndex
+		Unsigned32,
+	snAgentPoeUnitPowerCapacityTotal
+		Unsigned32,
+	snAgentPoeUnitPowerCapacityFree
+		Unsigned32,
+	snAgentPoeUnitPowerAllocationsRequestsHonored
+		Unsigned32
+	}
+
+snAgentPoeUnitIndex OBJECT-TYPE
+    SYNTAX  Unsigned32
+	MAX-ACCESS	read-only
+	STATUS	current
+	DESCRIPTION
+		"The Index to POE unit Table."
+	::= { snAgentPoeUnitEntry 1 }
+
+snAgentPoeUnitPowerCapacityTotal  OBJECT-TYPE
+	SYNTAX Unsigned32
+	MAX-ACCESS	read-only
+	STATUS	current
+	DESCRIPTION
+		"This object shows the total inline power capacity available on that unit (device), measured in mWatts. "
+	::= { snAgentPoeUnitEntry 2 }
+
+snAgentPoeUnitPowerCapacityFree  OBJECT-TYPE
+	SYNTAX Unsigned32
+	MAX-ACCESS	read-only
+	STATUS	current
+	DESCRIPTION
+		"This object shows the inline power capacity currently available on that unit (device) which is unallocated, measured in mWatts."
+	::= { snAgentPoeUnitEntry 3 }
+
+snAgentPoeUnitPowerAllocationsRequestsHonored   OBJECT-TYPE
+	SYNTAX Unsigned32
+	MAX-ACCESS	read-only
+	STATUS	current
+	DESCRIPTION
+		"This object shows number of times the inline power allocations requests honored on that unit (device)."
+	::= { snAgentPoeUnitEntry 4}
+
+END
+

mibs/FDRY-RADIUS-MIB

@@ -0,0 +1,191 @@
+FDRY-RADIUS-MIB DEFINITIONS ::= BEGIN
+
+IMPORTS
+	MODULE-IDENTITY, OBJECT-TYPE,
+			Unsigned32	   	FROM SNMPv2-SMI	  			-- [RFC2578]
+	RowStatus, TEXTUAL-CONVENTION		FROM SNMPv2-TC 				-- [RFC2579]
+	DisplayString		 				FROM SNMPv2-TC 		 		-- [RFC2579]
+
+	InetAddressType, InetAddress		FROM INET-ADDRESS-MIB		-- [RFC 4001]
+	fdryRadius	 					   	FROM FOUNDRY-SN-ROOT-MIB	-- [snroo101]
+	;
+
+fdryRadiusMIB MODULE-IDENTITY
+    LAST-UPDATED "201006020000Z"  -- 04 June 2010
+    ORGANIZATION "Brocade Communications Systems, Inc."
+    CONTACT-INFO
+             "Technical Support Center
+              130 Holger Way,
+              San Jose, CA  95134
+              Email:  ipsupport@brocade.com
+              Phone: 1-800-752-8061
+              URL:  www.brocade.com"
+    DESCRIPTION
+             "The Brocade proprietary MIB module for Radius Authentication Servers
+              It has new table combines Ipv4 and Ipv6 Radius Authentication Servers configuration.
+
+              Copyright 1996-2010 Brocade Communications Systems, Inc.
+              All rights reserved.
+              This Brocade Communications Systems SNMP Management Information Base Specification
+              embodies Brocade Communications Systems' confidential and proprietary
+              intellectual property. Brocade Communications Systems retains all
+              title and ownership in the Specification, including any revisions.
+
+              This Specification is supplied AS IS, and Brocade Communications Systems makes
+              no warranty, either express or implied, as to the use,
+              operation, condition, or performance of the specification, and any unintended
+              consequence it may on the user environment."
+
+    REVISION        "201006020000Z"  -- 04 June 2010
+    DESCRIPTION
+        "Changed the ORGANIZATION, CONTACT-INFO and DESCRIPTION fields."
+
+
+    REVISION 	"200802250000Z"  -- 25 February 2008
+    DESCRIPTION	"Initial version, obsoletes the earlier snRadiusServerTable."
+
+	::= { fdryRadius 1 }
+
+	--
+	-- Textual Conventions
+	--
+	ServerUsage ::= TEXTUAL-CONVENTION
+		STATUS	  current
+		DESCRIPTION
+			"Represents usage of the server for Authentication, Authorization or Accounting purpose."
+		SYNTAX	INTEGER{
+			default(1),
+			authenticationOnly(2),
+			authorizationOnly(3),
+			accountingOnly(4) }
+
+	--
+	-- Top level components of this MIB.
+	--
+
+	fdryRadiusServer OBJECT IDENTIFIER ::= { fdryRadiusMIB 1 }
+
+	--
+	-- Ipv4/Ipv6  Radius server table
+	--
+
+fdryRadiusServerTable        OBJECT-TYPE
+	SYNTAX  SEQUENCE OF FdryRadiusServerEntry
+	MAX-ACCESS  not-accessible
+	STATUS  current
+	DESCRIPTION
+		"Radius server table, listing the RADIUS authentication servers.
+		This table is currently supported by FastIron platform."
+	::= { fdryRadiusServer 1 }
+
+fdryRadiusServerEntry        OBJECT-TYPE
+	SYNTAX  FdryRadiusServerEntry
+	MAX-ACCESS  not-accessible
+	STATUS  current
+	DESCRIPTION
+		"An entry in the Radius server table. This table uses running index as the Index to the table.
+		  Reasons to go for running index Scheme than IP addresses:
+		  1.  The table will be Virtual Routing and Forwarding(VRF) independent
+			  that multiple VRFs could share the same address type and address.
+		  2.  Index with address type and address could be potentially 17 unsigned integer, parsing and finding next index takes CPU time.
+			  The PDU gets to be huge too!
+		  3.  IP address is just another attribute, they are supposed to be list of servers."
+	INDEX   { fdryRadiusServerIndex }
+	::= { fdryRadiusServerTable 1 }
+
+FdryRadiusServerEntry ::= SEQUENCE {
+	fdryRadiusServerIndex
+		Unsigned32,
+	fdryRadiusServerAddrType
+		InetAddressType,
+	fdryRadiusServerAddr
+		InetAddress,
+	fdryRadiusServerAuthPort
+		Unsigned32,
+	fdryRadiusServerAcctPort
+		Unsigned32,
+	fdryRadiusServerRowKey
+		DisplayString,
+	fdryRadiusServerUsage
+		ServerUsage,
+	fdryRadiusServerRowStatus
+		RowStatus
+	}
+
+fdryRadiusServerIndex OBJECT-TYPE
+	SYNTAX	Unsigned32
+	MAX-ACCESS	not-accessible
+	STATUS	current
+	DESCRIPTION
+		"The index to the Radius server Table.
+		FastIron platform supports upto 8 servers."
+	::= { fdryRadiusServerEntry 1 }
+
+fdryRadiusServerAddrType			 OBJECT-TYPE
+	SYNTAX	InetAddressType
+	MAX-ACCESS	read-create
+	STATUS	current
+	DESCRIPTION
+		"Radius server IP address Type.
+		FastIron supports address types of ipv4(1) and ipv6(2)."
+	DEFVAL	{ ipv4 }
+	::= { fdryRadiusServerEntry 2 }
+
+fdryRadiusServerAddr			 OBJECT-TYPE
+	SYNTAX	InetAddress
+	MAX-ACCESS	read-create
+	STATUS	current
+	DESCRIPTION
+		  "Radius server IP address."
+	::= { fdryRadiusServerEntry 3 }
+
+fdryRadiusServerAuthPort     OBJECT-TYPE
+	SYNTAX  Unsigned32
+	MAX-ACCESS  read-create
+	STATUS  current
+	DESCRIPTION
+		"Authentication UDP port number.
+		FastIron platform supports default value 1645."
+	::= { fdryRadiusServerEntry 4 }
+
+fdryRadiusServerAcctPort     OBJECT-TYPE
+	SYNTAX  Unsigned32
+	MAX-ACCESS  read-create
+	STATUS  current
+	DESCRIPTION
+		"Account UDP port number.
+		FastIron platform supports default value 1646."
+	::= { fdryRadiusServerEntry 5 }
+
+fdryRadiusServerRowKey       OBJECT-TYPE
+	SYNTAX  DisplayString
+	MAX-ACCESS  read-create
+	STATUS  current
+	DESCRIPTION
+		"Authentication key displayed as encrypted text.
+		FastIron platform supports keysize upto 32 characters."
+	::= { fdryRadiusServerEntry 6 }
+
+fdryRadiusServerUsage    OBJECT-TYPE
+	SYNTAX	ServerUsage
+	MAX-ACCESS  read-create
+	STATUS  current
+	DESCRIPTION
+		"To allow this server to be dedicated for a particular AAA activity."
+	DEFVAL  { default }
+	::= { fdryRadiusServerEntry 7 }
+
+fdryRadiusServerRowStatus    OBJECT-TYPE
+	SYNTAX	RowStatus
+	MAX-ACCESS  read-create
+	STATUS  current
+	DESCRIPTION
+		"This variable is used to create, modify, or
+		delete a row in this table. When a row in this
+		table is in active(1) state, no objects in that row
+		can be modified except this object.
+		 "
+	::= { fdryRadiusServerEntry 8 }
+
+	END
+

mibs/FDRY-SNTP-MIB

@@ -0,0 +1,144 @@
+FDRY-SNTP-MIB DEFINITIONS ::= BEGIN
+
+IMPORTS
+	MODULE-IDENTITY, OBJECT-TYPE,
+			Integer32, Unsigned32	   	FROM SNMPv2-SMI	  			-- [RFC2578]
+	RowStatus							FROM SNMPv2-TC 				-- [RFC2579]
+	InetAddressType, InetAddress		FROM INET-ADDRESS-MIB		-- [RFC 4001]
+	fdrySntp	 					   	FROM FOUNDRY-SN-ROOT-MIB 	-- [snroo101]
+	;
+
+fdrySntpMIB MODULE-IDENTITY
+    LAST-UPDATED "201006020000Z"  -- 04 June 2010
+    ORGANIZATION "Brocade Communications Systems, Inc."
+    CONTACT-INFO
+             "Technical Support Center
+              130 Holger Way,
+              San Jose, CA  95134
+              Email:  ipsupport@brocade.com
+              Phone: 1-800-752-8061
+              URL:  www.brocade.com "
+    DESCRIPTION
+              "The Brocade Communications Systems proprietary MIB module for
+               Simple Network Time Protocol(SNTP). It has new table combines
+               Ipv4 and Ipv6 Simple Network Time Protocol server configuration.
+
+               Copyright 1996-2010 Brocade Communications Systems, Inc.
+               All rights reserved.
+               This Brocade Communications Systems SNMP Management Information Base Specification
+               embodies Brocade Communications Systems' confidential and proprietary
+               intellectual property. Brocade Communications Systems retains all
+               title and ownership in the Specification, including any revisions.
+
+               This Specification is supplied AS IS, and Brocade Communications Systems makes
+               no warranty, either express or implied, as to the use,
+               operation, condition, or performance of the specification, and any unintended
+               consequence it may on the user environment."
+
+    REVISION        "201006020000Z"  -- 04 June 2010
+    DESCRIPTION  "Changed the ORGANIZATION, CONTACT-INFO and DESCRIPTION fields."
+
+    REVISION 	"200802250000Z"  -- 25 February 2008
+    DESCRIPTION	"Initial version, obsoletes the earlier snNTPServerTable."
+
+	::= { fdrySntp 1 }
+
+	--
+	-- Top level components of this MIB.
+	--
+
+	fdrySntpServer OBJECT IDENTIFIER ::= { fdrySntpMIB 1 }
+
+	--
+	-- Ipv4/Ipv6  SNTP server table
+	--
+
+	fdrySntpServerTable			 OBJECT-TYPE
+		SYNTAX  SEQUENCE OF FdrySntpServerTable
+		MAX-ACCESS  not-accessible
+		STATUS  current
+		DESCRIPTION
+			  "Simple Network Time Protocol(SNTP) server table.
+			   This table is not supported in NI devices from R5.3"
+		::= { fdrySntpServer 1 }
+
+	fdrySntpServerEntry			 OBJECT-TYPE
+		SYNTAX  FdrySntpServerTable
+		MAX-ACCESS  not-accessible
+		STATUS  current
+		DESCRIPTION
+			  "An entry in the SNTP server table. This table uses running index as the Index to the table.
+			  	Reasons to go for running index Scheme than IP addresses:
+				1.	The table will be Virtual Routing and Forwarding(VRF) independent
+					that multiple VRFs could share the same address type and address.
+				2.	Index with address type and address could be potentially 17 unsigned integer, parsing and finding next index takes CPU time.
+					The PDU gets to be huge too!
+				3. 	IP address is just another attribute, they are supposed to be list of servers."
+
+		INDEX   { fdrySntpServerIndex }
+		::= { fdrySntpServerTable 1 }
+
+	FdrySntpServerTable ::= SEQUENCE {
+		fdrySntpServerIndex
+			Unsigned32,
+		fdrySntpServerAddrType
+			InetAddressType,
+		fdrySntpServerAddr
+			InetAddress,
+		fdrySntpServerVersion
+			Integer32,
+		fdrySntpServerRowStatus
+			RowStatus
+		}
+
+	fdrySntpServerIndex OBJECT-TYPE
+		SYNTAX  Unsigned32
+		MAX-ACCESS  not-accessible
+		STATUS  current
+		DESCRIPTION
+			  "The index to the SNTP server Table. Maximum 3 Sntp servers are supported."
+		::= { fdrySntpServerEntry 1 }
+
+	fdrySntpServerAddrType 			 OBJECT-TYPE
+		SYNTAX  InetAddressType
+		MAX-ACCESS  read-create
+		STATUS  current
+		DESCRIPTION
+			  "SNTP server IP address Type. Supported address types are ipv4(1) and ipv6(2)"
+		DEFVAL  { ipv4 }
+		::= { fdrySntpServerEntry 2 }
+
+	fdrySntpServerAddr 			 OBJECT-TYPE
+		SYNTAX  InetAddress
+		MAX-ACCESS  read-create
+		STATUS  current
+		DESCRIPTION
+			  "SNTP server IP address."
+		::= { fdrySntpServerEntry 3 }
+
+	fdrySntpServerVersion		 OBJECT-TYPE
+		SYNTAX  Integer32 (1..4)
+		MAX-ACCESS  read-create
+		STATUS  current
+		DESCRIPTION
+			"SNTP server version."
+		DEFVAL  { 3 }
+		::= { fdrySntpServerEntry 4 }
+
+	fdrySntpServerRowStatus		 OBJECT-TYPE
+		SYNTAX  RowStatus
+		MAX-ACCESS  read-create
+		STATUS  current
+		DESCRIPTION
+			"This variable is used to create, modify, or
+			delete a row in this table. When a row in this
+			table is in active(1) state, no objects in that row
+			can be modified except this object.
+			 "
+		::= { fdrySntpServerEntry 5 }
+
+END
+
+
+
+

mibs/FDRY-TACACS-MIB

@@ -0,0 +1,166 @@
+FDRY-TACACS-MIB DEFINITIONS ::= BEGIN
+
+IMPORTS
+	MODULE-IDENTITY, OBJECT-TYPE,
+			Unsigned32	   	FROM SNMPv2-SMI	  			-- [RFC2578]
+	RowStatus							FROM SNMPv2-TC 				-- [RFC2579]
+	DisplayString		 				FROM SNMPv2-TC 		 		-- [RFC2579]
+
+	InetAddressType, InetAddress		FROM INET-ADDRESS-MIB
+	fdryTacacs	 					   	FROM FOUNDRY-SN-ROOT-MIB	-- [snroo101]
+	ServerUsage							FROM FDRY-RADIUS-MIB		-- [fdryradius]
+	;
+
+fdryTacacsMIB MODULE-IDENTITY
+    LAST-UPDATED "201006020000Z"  -- 04 June 2010
+    ORGANIZATION "Brocade Communications Systems, Inc."
+    CONTACT-INFO
+             "Technical Support Center
+              130 Holger Way,
+              San Jose, CA  95134
+              Email:  ipsupport@brocade.com
+              Phone: 1-800-752-8061
+              URL:  www.brocade.com"
+    DESCRIPTION
+             "The Brocade proprietary MIB module for Tacacs Authentication Servers
+               It has new table combines Ipv4 and Ipv6 Tacacs Authentication Servers configuration.
+
+              Copyright 1996-2010 Brocade Communications Systems, Inc.
+              All rights reserved.
+              This Brocade Communications Systems SNMP Management Information Base Specification
+              embodies Brocade Communications Systems' confidential and proprietary
+              intellectual property. Brocade Communications Systems retains all
+              title and ownership in the Specification, including any revisions.
+
+              This Specification is supplied AS IS, and Brocade Communications Systems makes
+              no warranty, either express or implied, as to the use,
+              operation, condition, or performance of the specification, and any unintended
+              consequence it may on the user environment."
+
+    REVISION        "201006020000Z"  -- 04 June 2010
+    DESCRIPTION
+        "Changed the ORGANIZATION, CONTACT-INFO and DESCRIPTION fields."
+
+    REVISION 	"200802250000Z"  -- 25 February 2008
+    DESCRIPTION	"Initial version, obsoletes the earlier snTacacsServerTable."
+
+	::= { fdryTacacs 1 }
+
+--
+-- Top level components of this MIB.
+--
+
+fdryTacacsServer OBJECT IDENTIFIER ::= { fdryTacacsMIB 1 }
+
+--
+-- Ipv4/Ipv6  Tacacs server table
+--
+
+	fdryTacacsServerTable 	   OBJECT-TYPE
+		SYNTAX	SEQUENCE OF FdryTacacsServerEntry
+		MAX-ACCESS	not-accessible
+		STATUS	current
+		DESCRIPTION
+			"Tacacs server table, listing the Tacacs authentication servers.
+			This table is currently supported by FastIron platform."
+		::= { fdryTacacsServer 1 }
+
+	fdryTacacsServerEntry 	   OBJECT-TYPE
+		SYNTAX	FdryTacacsServerEntry
+		MAX-ACCESS	not-accessible
+		STATUS	current
+		DESCRIPTION
+			"An entry in the Tacacs server table. This table uses running index as the Index to the table.
+			  Reasons to go for running index Scheme than IP addresses:
+			  1.  The table will be Virtual Routing and Forwarding(VRF) independent
+				  that multiple VRFs could share the same address type and address.
+			  2.  Index with address type and address could be potentially 17 unsigned integer, parsing and finding next index takes CPU time.
+				  The PDU gets to be huge too!
+			  3.  IP address is just another attribute, they are supposed to be list of servers."
+		INDEX	{ fdryTacacsServerIndex }
+		::= { fdryTacacsServerTable 1 }
+
+	FdryTacacsServerEntry ::= SEQUENCE {
+		fdryTacacsServerIndex
+			Unsigned32,
+		fdryTacacsServerAddrType
+			InetAddressType,
+		fdryTacacsServerAddr
+			InetAddress,
+		fdryTacacsServerAuthPort
+			Unsigned32,
+		fdryTacacsServerRowKey
+			DisplayString,
+		fdryTacacsServerUsage
+			ServerUsage,
+		fdryTacacsServerRowStatus
+			RowStatus
+		}
+
+	fdryTacacsServerIndex OBJECT-TYPE
+		SYNTAX  Unsigned32
+		MAX-ACCESS  not-accessible
+		STATUS  current
+		DESCRIPTION
+			"The index to the Tacacs server Table.
+			FastIron platform supports upto 8 servers."
+		::= { fdryTacacsServerEntry 1 }
+
+	fdryTacacsServerAddrType 			 OBJECT-TYPE
+		SYNTAX  InetAddressType
+		MAX-ACCESS  read-create
+		STATUS  current
+		DESCRIPTION
+			"Tacacs server IP address Type.
+			FastIron supports address types of ipv4(1) and ipv6(2)."
+		DEFVAL	{ ipv4 }
+		::= { fdryTacacsServerEntry 2 }
+
+	fdryTacacsServerAddr 			 OBJECT-TYPE
+		SYNTAX  InetAddress
+		MAX-ACCESS  read-create
+		STATUS  current
+		DESCRIPTION
+			  "Tacacs server IP address."
+		::= { fdryTacacsServerEntry 3 }
+
+	fdryTacacsServerAuthPort	   OBJECT-TYPE
+		SYNTAX	Unsigned32
+		MAX-ACCESS	read-create
+		STATUS	current
+		DESCRIPTION
+			"Authentication UDP port number."
+		DEFVAL	{ 49 }
+		::= { fdryTacacsServerEntry 4 }
+
+	fdryTacacsServerRowKey	   OBJECT-TYPE
+		SYNTAX	DisplayString
+		MAX-ACCESS	read-create
+		STATUS	current
+		DESCRIPTION
+			"Authentication key displayed as encrypted text.
+			FastIron platform supports keysize upto 32 characters."
+		::= { fdryTacacsServerEntry 5 }
+
+	fdryTacacsServerUsage    OBJECT-TYPE
+		SYNTAX	ServerUsage
+		MAX-ACCESS	read-create
+		STATUS	current
+		DESCRIPTION
+			"To allow this server to be dedicated for a particular AAA activity."
+		DEFVAL	{ default }
+		::= { fdryTacacsServerEntry 6 }
+
+	fdryTacacsServerRowStatus    OBJECT-TYPE
+		SYNTAX	RowStatus
+		MAX-ACCESS	read-create
+		STATUS	current
+		DESCRIPTION
+			"This variable is used to create, modify, or
+			delete a row in this table. When a row in this
+			table is in active(1) state, no objects in that row
+			can be modified except this object.
+			 "
+		::= { fdryTacacsServerEntry 7 }
+
+	END

mibs/FDRY-TRAP-MIB

@@ -0,0 +1,202 @@
+FDRY-TRAP-MIB DEFINITIONS ::= BEGIN
+
+IMPORTS
+	MODULE-IDENTITY, OBJECT-TYPE,
+			Integer32, Unsigned32	   	FROM SNMPv2-SMI	  			-- [RFC2578]
+	RowStatus, TEXTUAL-CONVENTION		FROM SNMPv2-TC 				-- [RFC2579]
+
+	InetAddressType, InetAddress		FROM INET-ADDRESS-MIB
+	fdryTrap	 					   	FROM FOUNDRY-SN-ROOT-MIB	-- [snroo101]
+	;
+
+fdryTrapMIB MODULE-IDENTITY
+    LAST-UPDATED "201006020000Z"  -- 04 June 2010
+    ORGANIZATION "Brocade Communications Systems, Inc."
+    CONTACT-INFO
+             "Technical Support Center
+              130 Holger Way,
+              San Jose, CA  95134
+              Email:  ipsupport@brocade.com
+              Phone: 1-800-752-8061
+              URL:  www.brocade.com"
+    DESCRIPTION
+             "The Brocade proprietary MIB module for Traps.
+              It has new table combines Ipv4 and Ipv6 configuration of
+              trap Receiver/managers which to send traps.
+
+              Copyright 1996-2010 Brocade Communications Systems, Inc.
+              All rights reserved.
+              This Brocade Communications Systems SNMP Management Information Base Specification
+              embodies Brocade Communications Systems' confidential and proprietary
+              intellectual property. Brocade Communications Systems retains all
+              title and ownership in the Specification, including any revisions.
+
+              This Specification is supplied AS IS, and Brocade Communications Systems makes
+              no warranty, either express or implied, as to the use,
+              operation, condition, or performance of the specification, and any unintended
+              consequence it may on the user environment."
+
+    REVISION        "201006020000Z"  -- 04 June 2010
+    DESCRIPTION
+        "Changed the ORGANIZATION, CONTACT-INFO and DESCRIPTION fields."
+
+	REVISION 	"200802250000Z"  -- 25 February 2008
+	DESCRIPTION	"Initial version, obsoletes the earlier snAgTrpRcvrTable."
+
+	::= { fdryTrap 1 }
+
+--
+-- Textual Conventions
+--
+SecurityModel ::= TEXTUAL-CONVENTION
+	STATUS	  current
+	DESCRIPTION
+		"Represents version of trap format to be used."
+	SYNTAX	INTEGER{
+		v1(1),
+		v2c(2),
+		usm(3)
+		}
+
+SecurityLevel ::= TEXTUAL-CONVENTION
+	STATUS	  current
+	DESCRIPTION
+		"Represents security levels to be used."
+	SYNTAX	INTEGER {
+		noAuth(1),
+		auth(2),
+		authPriv(3)
+		}
+
+--
+-- Top level components of this MIB.
+--
+
+fdryTrapReceiver OBJECT IDENTIFIER ::= { fdryTrapMIB 1 }
+
+--
+-- Ipv4/Ipv6  trap receiver table
+--
+
+	fdryTrapReceiverTable 	   OBJECT-TYPE
+		SYNTAX	SEQUENCE OF FdryTrapReceiverEntry
+		MAX-ACCESS	not-accessible
+		STATUS	current
+		DESCRIPTION
+			"Trap Receiver table."
+		::= { fdryTrapReceiver 1 }
+
+	fdryTrapReceiverEntry 	   OBJECT-TYPE
+		SYNTAX	FdryTrapReceiverEntry
+		MAX-ACCESS	not-accessible
+		STATUS	current
+		DESCRIPTION
+			"An entry in the Trap Receiver table. This table uses running index as the Index to the table.
+			  Reasons to go for running index Scheme than IP addresses:
+			  1.  The table will be Virtual Routing and Forwarding(VRF) independent
+				  that multiple VRFs could share the same address type and address.
+			  2.  Index with address type and address could be potentially 17 unsigned integer, parsing and finding next index takes CPU time.
+				  The PDU gets to be huge too!
+			  3.  IP address is just another attribute, they are supposed to be list of servers."
+		INDEX	{ fdryTrapReceiverIndex }
+		::= { fdryTrapReceiverTable 1 }
+
+	FdryTrapReceiverEntry ::= SEQUENCE {
+		fdryTrapReceiverIndex
+			Unsigned32,
+		fdryTrapReceiverAddrType
+			InetAddressType,
+		fdryTrapReceiverAddr
+			InetAddress,
+		fdryTrapReceiverCommunityOrSecurityName
+			OCTET STRING,
+		fdryTrapReceiverUDPPort
+			Integer32,
+		fdryTrapReceiverSecurityModel
+			SecurityModel,
+		fdryTrapReceiverSecurityLevel
+			SecurityLevel,
+		fdryTrapReceiverRowStatus
+			RowStatus
+		}
+
+	fdryTrapReceiverIndex OBJECT-TYPE
+		SYNTAX  Unsigned32
+		MAX-ACCESS  not-accessible
+		STATUS  current
+		DESCRIPTION
+		"The index to the Trap Receiver Table."
+		::= { fdryTrapReceiverEntry 1 }
+
+	fdryTrapReceiverAddrType 			 OBJECT-TYPE
+		SYNTAX  InetAddressType
+		MAX-ACCESS  read-create
+		STATUS  current
+		DESCRIPTION
+			  "Trap Receiver IP address Type. Supported address types are ipv4(1) and ipv6(2)"
+		DEFVAL	{ ipv4 }
+		::= { fdryTrapReceiverEntry 2 }
+
+	fdryTrapReceiverAddr 			 OBJECT-TYPE
+		SYNTAX  InetAddress
+		MAX-ACCESS  read-create
+		STATUS  current
+		DESCRIPTION
+			  "Trap Receiver IP address."
+		::= { fdryTrapReceiverEntry 3 }
+
+	fdryTrapReceiverCommunityOrSecurityName OBJECT-TYPE
+		SYNTAX	OCTET STRING (SIZE(0..32))
+		MAX-ACCESS	read-create
+		STATUS	current
+		DESCRIPTION
+			"Community string to use. In case of USM (SNMPv3) security model,
+			this object is used to provide the security name."
+		::= { fdryTrapReceiverEntry 4 }
+
+	fdryTrapReceiverUDPPort		 OBJECT-TYPE
+		SYNTAX	Integer32  (0..65535)
+		MAX-ACCESS	read-create
+		STATUS	current
+		DESCRIPTION
+			"UDP port number of the trap receiver."
+		DEFVAL { 162 }
+		::= { fdryTrapReceiverEntry 5 }
+
+	fdryTrapReceiverSecurityModel	   OBJECT-TYPE
+		SYNTAX	SecurityModel
+		MAX-ACCESS	read-create
+		STATUS	current
+		DESCRIPTION
+			"Version of trap format to be used."
+		DEFVAL { v1 }
+		::= { fdryTrapReceiverEntry 6 }
+
+	fdryTrapReceiverSecurityLevel	   OBJECT-TYPE
+		SYNTAX	SecurityLevel
+		MAX-ACCESS	read-create
+		STATUS	current
+		DESCRIPTION
+			"Used for USM (SNMPv3) security model to specify the level of security.
+			The security name is provided by fdryTrapReceiverCommunityOrSecurityName."
+		DEFVAL { noAuth }
+		::= { fdryTrapReceiverEntry 7 }
+
+	fdryTrapReceiverRowStatus    OBJECT-TYPE
+		SYNTAX	RowStatus
+		MAX-ACCESS	read-create
+		STATUS	current
+		DESCRIPTION
+			"This variable is used to create, modify, or
+			delete a row in this table. When a row in this
+			table is in active(1) state, no objects in that row
+			can be modified except this object.
+			 "
+		::= { fdryTrapReceiverEntry 8 }
+
+
+	END
+--
+-- FDRY-DNS2-MIB
+--
+

mibs/FOUNDRY-BFD-STD-MIB

@@ -0,0 +1,847 @@
+FOUNDRY-BFD-STD-MIB DEFINITIONS ::= BEGIN
+   IMPORTS
+      MODULE-IDENTITY, OBJECT-TYPE,
+      Unsigned32, Counter32, Counter64,
+      NOTIFICATION-TYPE
+         FROM SNMPv2-SMI                        -- [RFC2578]
+
+      TEXTUAL-CONVENTION, TruthValue,
+      RowStatus, StorageType, TimeStamp
+         FROM SNMPv2-TC                         -- [RFC2579]
+
+      MODULE-COMPLIANCE, OBJECT-GROUP,
+      NOTIFICATION-GROUP
+          FROM SNMPv2-CONF                      -- [RFC2580]
+
+      InetAddress, InetAddressType, InetPortNumber
+         FROM INET-ADDRESS-MIB                  -- [RFC3291]
+      bfd
+        FROM FOUNDRY-SN-ROOT-MIB
+
+   ;
+
+   bfdMIB MODULE-IDENTITY
+      LAST-UPDATED "200507221200Z"  -- 04 July 2005 12:00:00 EST
+      ORGANIZATION "IETF"
+      CONTACT-INFO
+          "        Thomas D. Nadeau
+                   Cisco Systems, Inc.
+           Email:  tnadeau@cisco.com
+
+                   Zafar Ali
+                   Cisco Systems, Inc.
+           Email:  zali@cisco.com
+          "
+      DESCRIPTION
+          "Bidirectional Forwarding Management Information Base."
+
+      -- Revision history.
+      REVISION
+          "200508221200Z"  -- 04 August 2005 12:00:00 EST
+      DESCRIPTION
+      "Initial version. Published as RFC xxxx." -- RFC-editor pls fill
+                                                -- in xxxx
+   ::= { bfd 1 }
+--   ::= { mib-2 XXX }
+
+   -- Top level components of this MIB module.
+
+   bfdNotifications OBJECT IDENTIFIER ::= { bfdMIB 0 }
+
+   bfdObjects       OBJECT IDENTIFIER ::= { bfdMIB 1 }
+
+   bfdConformance   OBJECT IDENTIFIER ::= { bfdMIB 3 }
+
+   bfdScalarObjects OBJECT IDENTIFIER ::= { bfdObjects 1 }
+
+
+   --  Textual Conventions
+
+      BfdSessIndexTC ::= TEXTUAL-CONVENTION
+      DISPLAY-HINT "d"
+      STATUS        current
+      DESCRIPTION
+          "An index used to uniquely identify BFD sessions."
+      SYNTAX Unsigned32 (1..4294967295)
+
+      BfdInterval ::= TEXTUAL-CONVENTION
+      STATUS        current
+      DESCRIPTION
+          "The BFD interval delay in microseconds."
+      SYNTAX        Unsigned32 (1..4294967295)
+
+      BfdDiag ::=      TEXTUAL-CONVENTION
+      STATUS        current
+      DESCRIPTION
+          "A common BFD diagnostic code."
+
+      SYNTAX INTEGER { noDiagnostic(1),
+                       controlDetectionTimeExpired(2),
+                       echoFunctionFailed(3),
+                       neighborSignaledSessionDown(4),
+                       forwardingPlaneReset(5),
+                       pathDown(6),
+                       concatenatedPathDown(7),
+                       administrativelyDown(8),
+                       reverseConcatenatedPathDown (9)
+                     }
+
+        --  BFD General Variables
+
+        --  These parameters apply globally to the Router's
+        --  BFD Process.
+
+        bfdAdminStatus OBJECT-TYPE
+           SYNTAX   INTEGER { enabled(1), disabled(2) }
+           MAX-ACCESS   read-write
+           STATUS   current
+           DESCRIPTION
+              "The global administrative status of BFD in this router.
+               The value 'enabled' denotes that the BFD Process is
+               active on at least one interface; 'disabled' disables
+               it on all interfaces."
+           DEFVAL { enabled }
+           ::= { bfdScalarObjects 1 }
+
+        bfdVersionNumber OBJECT-TYPE
+            SYNTAX   Unsigned32
+            MAX-ACCESS   read-only
+            STATUS   current
+            DESCRIPTION
+               "The current version number of the BFD protocol."
+            REFERENCE
+               " BFD Version 0 (draft-katz-ward-bfd-02.txt)"
+            DEFVAL { 0 }
+            ::= { bfdScalarObjects 3 }
+
+
+        --  BFD Session Table
+        --  The BFD Session Table specifies BFD session specific
+        --  information.
+
+        bfdSessTable OBJECT-TYPE
+            SYNTAX   SEQUENCE OF BfdSessEntry
+            MAX-ACCESS   not-accessible
+            STATUS   current
+            DESCRIPTION
+               "The BFD Session Table describes the BFD sessions."
+            REFERENCE
+               "BFD Version 0 (draft-katz-ward-bfd-02.txt)"
+            ::= { bfdObjects 2 }
+
+        bfdSessEntry OBJECT-TYPE
+            SYNTAX      BfdSessEntry
+            MAX-ACCESS  not-accessible
+            STATUS      current
+            DESCRIPTION
+               "The BFD Session Entry describes BFD session."
+            INDEX { bfdSessIndex }
+            ::= { bfdSessTable 1 }
+
+        BfdSessEntry ::= SEQUENCE {
+          bfdSessIndex                    BfdSessIndexTC,
+          bfdSessApplicationId            Unsigned32,
+          bfdSessDiscriminator            Unsigned32,
+          bfdSessRemoteDiscr              Unsigned32,
+          bfdSessUdpPort                  InetPortNumber,
+          bfdSessState                    INTEGER,
+          bfdSessRemoteHeardFlag          TruthValue,
+          bfdSessDiag                     Unsigned32,
+          bfdSessOperMode                 INTEGER,
+          bfdSessDemandModeDesiredFlag    TruthValue,
+          bfdSessEchoFuncModeDesiredFlag  TruthValue,
+          bfdSessControlPlanIndepFlag     TruthValue,
+          bfdSessAddrType                 InetAddressType,
+          bfdSessAddr                     InetAddress,
+          bfdSessDesiredMinTxInterval     BfdInterval,
+          bfdSessReqMinRxInterval         BfdInterval,
+          bfdSessReqMinEchoRxInterval     BfdInterval,
+          bfdSessDetectMult               Unsigned32,
+          bfdSessStorType                 StorageType,
+          bfdSessRowStatus                RowStatus,
+          bfdSessAuthPresFlag             TruthValue,
+          bfdSessAuthenticationType       INTEGER
+      }
+
+      bfdSessIndex  OBJECT-TYPE
+      SYNTAX        BfdSessIndexTC
+      MAX-ACCESS    not-accessible
+      STATUS        current
+      DESCRIPTION
+          "This object contains an index used to represent a
+           unique BFD session on this device."
+      ::= { bfdSessEntry 1 }
+
+   bfdSessApplicationId  OBJECT-TYPE
+      SYNTAX        Unsigned32
+      MAX-ACCESS    read-only
+      STATUS        current
+      DESCRIPTION
+          "This object contains an index used to indicate
+           a local application which owns or maintains this
+           BFD session. For instance, the MPLS VPN process may
+           maintain a subset of the total number of BFD
+           sessions.  This application ID provides a convenient
+           way to segregate sessions by the applications which
+           maintain them."
+      ::= { bfdSessEntry 2 }
+
+      bfdSessDiscriminator            OBJECT-TYPE
+      SYNTAX        Unsigned32 (1..4294967295)
+      MAX-ACCESS    read-only
+      STATUS        current
+      DESCRIPTION
+          "This object specifies the local discriminator for this BFD
+        session, used to uniquely identify it."
+      ::= { bfdSessEntry 3 }
+
+      bfdSessRemoteDiscr OBJECT-TYPE
+          SYNTAX        Unsigned32 (1..4294967295)
+          MAX-ACCESS    read-only
+          STATUS        current
+          DESCRIPTION
+            "This object specifies the session discriminator chosen
+             by the remote system for this BFD session."
+      ::= { bfdSessEntry 4 }
+
+      bfdSessUdpPort OBJECT-TYPE
+          SYNTAX      InetPortNumber
+          MAX-ACCESS  read-create
+          STATUS      current
+          DESCRIPTION
+              "The UDP Port for BFD. The default value is the
+              well-known value for this port."
+            REFERENCE
+                "draft-katz-ward-bfd-02.txt and
+                draft-raggarwa-mpls-bfd-00.txt"
+            DEFVAL { 0 }
+            ::= { bfdSessEntry 5 }
+
+      bfdSessState OBJECT-TYPE
+            SYNTAX   INTEGER {
+                  adminDown(1),
+                  down(2),
+                  init(3),
+                  up(4)
+            }
+            MAX-ACCESS   read-only
+            STATUS   current
+            DESCRIPTION
+               "The perceived state of the BFD session."
+            ::= { bfdSessEntry 6 }
+
+   bfdSessRemoteHeardFlag OBJECT-TYPE
+      SYNTAX        TruthValue
+      MAX-ACCESS    read-only
+      STATUS        current
+      DESCRIPTION
+            "This object specifies status of BFD packet reception from
+             the remote system. Specifically, it is set to true(1) if
+             the local system is actively receiving BFD packets from the
+             remote system, and is set to false(0) if the local system
+             has not received BFD packets recently (within the detection
+             time) or if the local system is attempting to tear down
+             the BFD session."
+      ::= { bfdSessEntry 7 }
+
+   bfdSessDiag OBJECT-TYPE
+            SYNTAX      Unsigned32
+            MAX-ACCESS  accessible-for-notify
+            STATUS      current
+            DESCRIPTION
+               "A diagnostic code specifying the local system's reason
+                for the last transition of the session from up(1)
+                to some other state."
+      ::= { bfdSessEntry 8 }
+
+   bfdSessOperMode OBJECT-TYPE
+            SYNTAX   INTEGER { asyncModeWEchoFun(1),
+                               asynchModeWOEchoFun(2),
+                               demandModeWEchoFunction(3),
+                               demandModeWOEchoFunction(4)
+             }
+           MAX-ACCESS   read-only
+           STATUS   current
+           DESCRIPTION
+               "This object specifies current operating mode that BFD
+                session is operating in.
+
+                A value of AsyncModeWEchoFun(1) ...
+                A value of AsynchModeWOEchoFun(2) ...
+                A value of DemandModeWEchoFunction(3) ...
+                A value of DemandModeWOEchoFunction(4) ...
+            "
+            ::= { bfdSessEntry 9 }
+
+   bfdSessDemandModeDesiredFlag OBJECT-TYPE
+      SYNTAX        TruthValue
+      MAX-ACCESS    read-create
+      STATUS        current
+      DESCRIPTION
+              "This object indicates that the local system's
+               desire to use Demand mode. Specifically, it is set
+               to true(1) if the local system wishes to use
+               Demand mode or false(0) if not"
+      DEFVAL { false }
+      ::= { bfdSessEntry 10 }
+
+   bfdSessEchoFuncModeDesiredFlag OBJECT-TYPE
+      SYNTAX        TruthValue
+      MAX-ACCESS    read-create
+      STATUS        current
+      DESCRIPTION
+              "This object indicates that the local system's
+               desire to use Echo mode. Specifically, it is set
+               to true(1) if the local system wishes to use
+               Echo mode or false(0) if not"
+      DEFVAL { false }
+      ::= { bfdSessEntry 11 }
+
+   bfdSessControlPlanIndepFlag     OBJECT-TYPE
+      SYNTAX        TruthValue
+      MAX-ACCESS    read-create
+      STATUS        current
+      DESCRIPTION
+          "This object indicates that the local system's
+           ability to continue to function through a disruption of
+           the control plane. Specifically, it is set
+           to true(1) if the local system BFD implementation is
+           independent of the control plane. Otherwise, the
+           value is set to false(0)"
+      DEFVAL { false }
+      ::= { bfdSessEntry 12 }
+
+   bfdSessAddrType  OBJECT-TYPE
+      SYNTAX        InetAddressType
+      MAX-ACCESS    read-create
+      STATUS        current
+      DESCRIPTION
+           "This object specifies IP address of the interface
+            associated with this BFD session.
+
+            Only values unknown(0), ipv4(1) or ipv6(2)
+            have to be supported.
+
+            A value of unknown(0) is allowed only when
+            the outgoing interface is of type point-to-point, or
+            when the BFD session is not associated with a specific
+            interface.
+
+            If any other unsupported values are attempted in a set
+            operation, the agent MUST return an inconsistentValue
+            error.
+      "
+      ::= { bfdSessEntry 13 }
+
+   bfdSessAddr OBJECT-TYPE
+      SYNTAX        InetAddress
+      MAX-ACCESS    read-create
+      STATUS        current
+      DESCRIPTION
+           "This object specifies IP address of the interface
+            associated with this BFD session.
+            It can also be used to enabled BFD on a specific
+            interface. The value is set to zero when BFD session is not
+            associated with a specific interface. "
+      ::= { bfdSessEntry 14 }
+
+   bfdSessDesiredMinTxInterval OBJECT-TYPE
+      SYNTAX    BfdInterval
+      MAX-ACCESS   read-create
+      STATUS    current
+      DESCRIPTION
+       "This object specifies the minimum interval, in
+        microseconds, that the local system would like to use when
+             transmitting BFD Control packets."
+      ::= { bfdSessEntry 15 }
+
+   bfdSessReqMinRxInterval     OBJECT-TYPE
+      SYNTAX        BfdInterval
+      MAX-ACCESS    read-create
+      STATUS        current
+      DESCRIPTION
+            "This object specifies the minimum interval, in
+             microseconds, between received  BFD Control packets the
+             local system is capable of supporting."
+      ::= { bfdSessEntry 16 }
+
+   bfdSessReqMinEchoRxInterval  OBJECT-TYPE
+      SYNTAX        BfdInterval
+      MAX-ACCESS    read-create
+      STATUS        current
+      DESCRIPTION
+            "This object specifies the minimum interval, in
+             microseconds, between received BFD Echo packets that this
+             system is capable of supporting."
+      ::= { bfdSessEntry 17 }
+
+   bfdSessDetectMult OBJECT-TYPE
+      SYNTAX        Unsigned32
+      MAX-ACCESS    read-create
+      STATUS        current
+      DESCRIPTION
+            "This object specifies the Detect time multiplier."
+      ::= { bfdSessEntry 18 }
+
+   bfdSessStorType  OBJECT-TYPE
+      SYNTAX        StorageType
+      MAX-ACCESS    read-create
+      STATUS        current
+      DESCRIPTION
+          "This variable indicates the storage type for this
+           object. Conceptual rows having the value
+           'permanent' need not allow write-access to any
+           columnar objects in the row."
+      ::= { bfdSessEntry 19 }
+
+   bfdSessRowStatus OBJECT-TYPE
+      SYNTAX        RowStatus
+      MAX-ACCESS    read-create
+      STATUS        current
+      DESCRIPTION
+            "This variable is used to create, modify, and/or
+             delete a row in this table. When a row in this
+             table has a row in the active(1) state, no
+             objects in this row can be modified except the
+             bfdSessRowStatus and bfdSessStorageType."
+      ::= { bfdSessEntry 20 }
+
+   bfdSessAuthPresFlag OBJECT-TYPE
+      SYNTAX        TruthValue
+      MAX-ACCESS    read-create
+      STATUS        current
+      DESCRIPTION
+              "This object indicates that the local system's
+               desire to use Authentication. Specifically, it is set
+               to true(1) if the local system wishes the session
+               to be authenticated or false(0) if not"
+      DEFVAL { false }
+      ::= { bfdSessEntry 21 }
+
+   bfdSessAuthenticationType OBJECT-TYPE
+            SYNTAX      INTEGER { simplePassword(1),
+                                  keyedMD5(2),
+                                  meticulousKeyedMD5(3),
+                                  keyedSHA1(4),
+                                  meticulousKeyedSHA1(5)
+             }
+            MAX-ACCESS  read-create
+            STATUS      current
+            DESCRIPTION
+               "The Authentication Type used for this BFD session. This
+   field is valid only when the Authentication Present bit is set"
+      ::= { bfdSessEntry 22 }
+
+   -- BFD Session Performance Table
+
+   bfdSessPerfTable OBJECT-TYPE
+      SYNTAX        SEQUENCE OF BfdSessPerfEntry
+      MAX-ACCESS    not-accessible
+      STATUS        current
+      DESCRIPTION
+          "This table specifies BFD Session performance counters."
+      ::= { bfdObjects 3 }
+
+   bfdSessPerfEntry OBJECT-TYPE
+      SYNTAX        BfdSessPerfEntry
+      MAX-ACCESS    not-accessible
+      STATUS        current
+      DESCRIPTION
+          "An entry in this table is created by a BFD-enabled node for
+           every BFD Session. bfdCounterDiscontinuityTime is used to
+           indicate potential discontinuity for all counter objects
+           in this table."
+      AUGMENTS    { bfdSessEntry }
+      ::= { bfdSessPerfTable 1 }
+
+   BfdSessPerfEntry ::= SEQUENCE {
+     bfdSessPerfPktIn               Counter32,
+     bfdSessPerfPktOut              Counter32,
+     bfdSessPerfUpTime                  TimeStamp,
+     bfdSessPerfLastSessDownTime    TimeStamp,
+     bfdSessPerfLastCommLostDiag    BfdDiag,
+     bfdSessPerfSessUpCount         Counter32,
+     bfdSessPerfDiscTime            TimeStamp,
+
+     -- High Capacity Counters
+     bfdSessPerfPktInHC             Counter64,
+     bfdSessPerfPktOutHC            Counter64
+     }
+
+   -- Ed Note: should we add per-diag code counts here,
+
+   bfdSessPerfPktIn OBJECT-TYPE
+       SYNTAX      Counter32
+       MAX-ACCESS  read-only
+       STATUS      current
+       DESCRIPTION
+           "The total number of BFD messages received for this BFD
+   session."
+       ::= { bfdSessPerfEntry 1 }
+
+   bfdSessPerfPktOut OBJECT-TYPE
+       SYNTAX      Counter32
+       MAX-ACCESS  read-only
+       STATUS      current
+       DESCRIPTION
+           "The total number of BFD messages sent for this BFD session."
+       ::= { bfdSessPerfEntry 2 }
+
+   bfdSessPerfUpTime OBJECT-TYPE
+       SYNTAX       TimeStamp
+       MAX-ACCESS   read-only
+       STATUS       current
+       DESCRIPTION
+           "The value of sysUpTime on the most recent occasion at which
+            the session came up. If no such up event exists this object
+            contains a zero value."
+       ::= { bfdSessPerfEntry 3 }
+
+   bfdSessPerfLastSessDownTime OBJECT-TYPE
+       SYNTAX       TimeStamp
+       MAX-ACCESS   read-only
+       STATUS       current
+       DESCRIPTION
+           "The value of sysUpTime on the most recent occasion at which
+            the last time communication was lost with the neighbor. If
+            no such down event exist this object contains a zero value."
+       ::= { bfdSessPerfEntry 4 }
+
+   bfdSessPerfLastCommLostDiag  OBJECT-TYPE
+       SYNTAX       BfdDiag
+       MAX-ACCESS   read-only
+       STATUS       current
+       DESCRIPTION
+           "The BFD diag code for the last time communication was lost
+            with the neighbor. If no such down event exists this object
+            contains a zero value."
+       ::= { bfdSessPerfEntry 5 }
+
+   bfdSessPerfSessUpCount OBJECT-TYPE
+       SYNTAX       Counter32
+       MAX-ACCESS   read-only
+       STATUS       current
+       DESCRIPTION
+           "The number of times this session has gone into the Up
+            state since the router last rebooted."
+       ::= { bfdSessPerfEntry 6 }
+
+   bfdSessPerfDiscTime OBJECT-TYPE
+       SYNTAX       TimeStamp
+       MAX-ACCESS   read-only
+       STATUS       current
+       DESCRIPTION
+         "The value of sysUpTime on the most recent occasion at
+          which any one or more of the session counters suffered
+          a discontinuity.
+
+          The relevant counters are the specific instances associated
+          with this BFD session of any Counter32 object contained in
+          the BfdSessPerfTable. If no such discontinuities have occurred
+          since the last re-initialization of the local management
+          subsystem, then this object contains a zero value."
+       ::= { bfdSessPerfEntry 7 }
+
+
+   bfdSessPerfPktInHC OBJECT-TYPE
+       SYNTAX       Counter64
+       MAX-ACCESS   read-only
+       STATUS       current
+       DESCRIPTION
+           "This value represents the total number of BFD messages
+            received for this BFD session. It MUST be equal to the
+            least significant 32 bits of bfdSessPerfPktIn
+            if bfdSessPerfPktInHC is supported according to
+            the rules spelled out in RFC2863."
+       ::= { bfdSessPerfEntry 8 }
+
+   bfdSessPerfPktOutHC OBJECT-TYPE
+       SYNTAX       Counter64
+       MAX-ACCESS   read-only
+       STATUS       current
+       DESCRIPTION
+           "This value represents the total number of
+            total number of BFD messages transmitted for this
+            BFD session. It MUST be equal to the
+           least significant 32 bits of bfdSessPerfPktIn
+           if bfdSessPerfPktOutHC is supported according to
+           the rules spelled out in RFC2863."
+       ::= { bfdSessPerfEntry 9 }
+
+
+   -- BFD Session Mapping Table
+
+        bfdSessMapTable OBJECT-TYPE
+            SYNTAX   SEQUENCE OF BfdSessMapEntry
+            MAX-ACCESS   not-accessible
+            STATUS   current
+            DESCRIPTION
+               "The BFD Session Mapping Table maps the complex
+                indexing of the BFD sessions to the flat
+                BFDIndex used in the BfdSessionTable.
+
+                Implementors need to be aware that if the value of
+                the bfdSessAddr (an OID) has more
+                that 111 sub-identifiers, then OIDs of column
+                instances in this table will have more than 128
+                sub-identifiers and cannot be accessed using SNMPv1,
+                SNMPv2c, or SNMPv3.
+               "
+            REFERENCE
+               "BFD Version 0 (draft-katz-ward-bfd-02.txt)"
+            ::= { bfdObjects 4 }
+
+        bfdSessMapEntry OBJECT-TYPE
+            SYNTAX   BfdSessMapEntry
+            MAX-ACCESS   not-accessible
+            STATUS   current
+            DESCRIPTION
+               "The BFD Session Entry describes BFD session
+                that is mapped to this index.
+
+                Implementors need to be aware that if the value of
+                the mplsInSegmentMapLabelPtrIndex (an OID) has more
+                that 111 sub-identifiers, then OIDs of column
+                instances in this table will have more than 128
+                sub-identifiers and cannot be accessed using SNMPv1,
+                SNMPv2c, or SNMPv3."
+            INDEX { bfdSessApplicationId,
+                    bfdSessDiscriminator,
+                    bfdSessAddrType,
+                    bfdSessAddr
+             }
+            ::= { bfdSessMapTable 1 }
+
+        BfdSessMapEntry ::= SEQUENCE {
+          bfdSessMapBfdIndex            BfdSessIndexTC
+        }
+
+   bfdSessMapBfdIndex OBJECT-TYPE
+      SYNTAX        BfdSessIndexTC
+      MAX-ACCESS    read-only
+      STATUS        current
+      DESCRIPTION
+          "This object specifies the BfdIndex referred to by
+           the indexes of this row. In essence, a mapping is
+           provided between these indexes and the BfdSessTable."
+      ::= { bfdSessMapEntry 1 }
+
+   -- Notification Configuration
+
+   bfdSessNotificationsEnable OBJECT-TYPE
+      SYNTAX        TruthValue
+      MAX-ACCESS    read-write
+      STATUS        current
+      DESCRIPTION
+          "If this object is set to true(1), then it enables
+           the emission of bfdSessUp and bfdSessDown
+           notifications; otherwise these notifications are not
+           emitted."
+      REFERENCE
+          "See also RFC3413 for explanation that
+           notifications are under the ultimate control of the
+           MIB modules in this document."
+      DEFVAL { false }
+      ::= { bfdScalarObjects 4 }
+
+   bfdSessUp NOTIFICATION-TYPE
+      OBJECTS     { bfdSessDiag, -- low range value
+                    bfdSessDiag  -- high range value
+      }
+      STATUS      current
+      DESCRIPTION
+          "This notification is generated when the
+           bfdSessState object for one or more contiguous
+           entries in bfdSessTable are about to enter the up(2)
+           state from some other state. The included values of
+           bfdSessDiag MUST both be set equal to this
+           new state (i.e: up(1)).  The two instances of
+           bfdSessDiag in this notification indicate the range
+           of indexes that are affected.  Note that all the indexes
+           of the two ends of the range can be derived from the
+           instance identifiers of these two objects.  For the
+           cases where a contiguous range of sessions
+           have transitioned into the up(1) state at roughly
+           the same time, the device SHOULD issue a single
+           notification for each range of contiguous indexes in
+           an effort to minimize the emission of a large number
+           of notifications.  If a notification has to be
+           issued for just a single bfdSessEntry, then
+           the instance identifier (and values) of the two
+           bfdSessDiag objects MUST be the identical."
+         --#TYPE "Foundry Trap: BFD Session Up"
+         --#SUMMARY "BFD session up for specified sessions in varbind indexes."
+         --#ARGUMENTS {}
+         --#SEVERITY INFORMATIONAL
+         --#STATE OPERATIONAL
+      ::= { bfdNotifications 1 }
+
+   bfdSessDown NOTIFICATION-TYPE
+      OBJECTS     { bfdSessDiag, -- low range value
+                    bfdSessDiag  -- high range value
+      }
+      STATUS      current
+      DESCRIPTION
+          "This notification is generated when the
+           bfdSessState object for one or more contiguous
+           entries in bfdSessTable are about to enter the down(4)
+           or adminDown(5) states from some other state. The included
+           values of bfdSessDiag MUST both be set equal to this
+           new state (i.e: down(4) or adminDown(5)).  The two instances
+           of bfdSessDiag in this notification indicate the range
+           of indexes that are affected.  Note that all the indexes
+           of the two ends of the range can be derived from the
+           instance identifiers of these two objects.  For
+           cases where a contiguous range of sessions
+           have transitioned into the down(4) or adminDown(5) states
+           at roughly the same time, the device SHOULD issue a single
+           notification for each range of contiguous indexes in
+           an effort to minimize the emission of a large number
+           of notifications.  If a notification has to be
+           issued for just a single bfdSessEntry, then
+           the instance identifier (and values) of the two
+           bfdSessDiag objects MUST be the identical."
+         --#TYPE "Foundry Trap: BFD Session Down"
+         --#SUMMARY "BFD session down due to code %d for specified sessions in varbind indexes."
+         --#ARGUMENTS { 0 }
+         --#SEVERITY INFORMATIONAL
+         --#STATE OPERATIONAL
+      ::= { bfdNotifications 2 }
+
+   -- Ed Note: We need to add notification for changes
+   -- when the two ends automatically negotiate to a new detection time
+   -- value or when detection multiplier changes.
+   -- Similarly, changes in the operating mode (bfdSessOperMode)
+   -- also need to be notified.
+
+   -- Module compliance.
+
+   bfdGroups
+      OBJECT IDENTIFIER ::= { bfdConformance 1 }
+
+   bfdCompliances
+      OBJECT IDENTIFIER ::= { bfdConformance 2 }
+
+   -- Compliance requirement for fully compliant implementations.
+
+   bfdModuleFullCompliance MODULE-COMPLIANCE
+      STATUS       current
+      DESCRIPTION "Compliance statement for agents that provide full
+                   support for BFD-MIB. Such devices can
+                   then be monitored and also be configured using
+                   this MIB module."
+
+      MODULE -- This module.
+      MANDATORY-GROUPS {
+            bfdSessionGroup,
+            bfdSessionPerfGroup,
+            bfdSessionPerfHCGroup,
+            bfdNotificationGroup
+      }
+
+      GROUP        bfdSessionPerfHCGroup
+      DESCRIPTION "This group is mandatory for those bfdPerfTable
+                   entries for which any of the objects
+                   bfdSessPerfPktInHC or bfdSessPerfPktOutHC
+                   wraps around too quickly
+                   based on the criteria specified in RFC 2863 for
+                   high-capacity counters."
+
+      GROUP        bfdNotificationGroup
+      DESCRIPTION "This group is only mandatory for those
+                   implementations which can efficiently implement
+                   the notifications contained in this group."
+
+      OBJECT       bfdSessAddrType
+      SYNTAX       INTEGER { unknown(0), ipv4(1), ipv6(2) }
+--      SYNTAX       InetAddressType { unknown(0), ipv4(1), ipv6(2) }
+      DESCRIPTION "Only unknown(0), ipv4(1) and ipv6(2) support
+                   is required."
+
+      OBJECT       bfdSessAddr
+      SYNTAX       InetAddress (SIZE(0|4|16))
+      DESCRIPTION "An implementation is only required to support
+                   unknown(0), ipv4(1) and ipv6(2) sizes."
+
+      ::= { bfdCompliances 1 }
+
+   -- Read-Only Conformance TBD...
+
+
+   -- Units of conformance.
+
+   bfdSessionGroup OBJECT-GROUP
+      OBJECTS {
+                bfdSessNotificationsEnable,
+                bfdAdminStatus,
+                bfdVersionNumber,
+                bfdSessApplicationId,
+                bfdSessDiscriminator,
+                bfdSessAddrType,
+                bfdSessAddr,
+                bfdSessRemoteDiscr,
+                bfdSessUdpPort,
+                bfdSessState,
+                bfdSessRemoteHeardFlag,
+                bfdSessDiag,
+                bfdSessOperMode,
+                bfdSessDemandModeDesiredFlag,
+                bfdSessEchoFuncModeDesiredFlag,
+                bfdSessControlPlanIndepFlag,
+                bfdSessDesiredMinTxInterval,
+                bfdSessReqMinRxInterval,
+                bfdSessReqMinEchoRxInterval,
+                bfdSessDetectMult,
+                bfdSessStorType,
+                bfdSessRowStatus,
+                bfdSessMapBfdIndex,
+                bfdSessAuthPresFlag,
+                bfdSessAuthenticationType
+      }
+      STATUS  current
+      DESCRIPTION
+             "Collection of objects needed for BFD sessions."
+      ::= { bfdGroups 1 }
+
+
+   bfdSessionPerfGroup OBJECT-GROUP
+      OBJECTS {
+                bfdSessPerfPktIn,
+                bfdSessPerfPktOut,
+                bfdSessPerfUpTime,
+                bfdSessPerfLastSessDownTime,
+                bfdSessPerfLastCommLostDiag,
+                bfdSessPerfSessUpCount,
+                bfdSessPerfDiscTime
+      }
+      STATUS  current
+      DESCRIPTION
+             "Collection of objects needed to monitor the
+              performance of BFD sessions."
+      ::= { bfdGroups 2 }
+
+   bfdSessionPerfHCGroup OBJECT-GROUP
+      OBJECTS {
+               bfdSessPerfPktInHC,
+               bfdSessPerfPktOutHC
+      }
+      STATUS  current
+      DESCRIPTION
+             "Collection of objects needed to monitor the
+              performance of BFD sessions for which the
+              values of bfdSessPerfPktIn, bfdSessPerfPktOut
+              wrap around too quickly."
+      ::= { bfdGroups 3 }
+
+   bfdNotificationGroup NOTIFICATION-GROUP
+      NOTIFICATIONS {
+                bfdSessUp,
+                bfdSessDown
+      }
+      STATUS  current
+      DESCRIPTION
+             "Set of notifications implemented in this
+              module."
+      ::= { bfdGroups 4 }
+
+   END

mibs/FOUNDRY-CAR-MIB

@@ -1,265 +1,376 @@
--- *****************************************************************
--- Commited Access Rate MIB file.
--- *****************************************************************
-FOUNDRY-CAR-MIB DEFINITIONS ::= BEGIN
-
-IMPORTS
-	OBJECT-TYPE,
-	Gauge
-		FROM RFC1155-SMI
-
-        Counter64
-		FROM SNMPv2-SMI
-
-
-	snCAR
-		FROM FOUNDRY-SN-SWITCH-GROUP-MIB;
-			
-
-snPortCARs	OBJECT IDENTIFIER ::= { snCAR 1 }
-
-PacketSource ::= INTEGER { 
-		input(0), --for inbound traffic
-		output(1) --for outbound traffic
-	}
-
-RateLimitType ::= INTEGER { 
-		all(3), 		--	all traffic.                             
-		quickAcc(2), 	--	traffic matches rate-limit's access list.
-		standardAcc(1) 	--	traffic matches standard access list.    
-	}
-
-RateLimitAction ::= INTEGER {
-		continue(1), 
-		drop(2), 
-		precedCont(3),
-		precedXmit(4), 
-		xmit(5) 
-	}
-
-
-snPortCARTable OBJECT-TYPE
-	SYNTAX  SEQUENCE OF SnPortCAREntry
-	ACCESS  not-accessible
-        STATUS  mandatory
-        DESCRIPTION
-        "A table of rate limit configuration entries.
-	Rate Limit is a method of traffic control.  It allows a set
-	of rate limits to be configured and applied to packets flowing
-	into/out of an interface to regulate network traffic."
-
-        ::= { snPortCARs 1 }
-
-snPortCAREntry OBJECT-TYPE
-        SYNTAX SnPortCAREntry
-        ACCESS  not-accessible
-        STATUS  mandatory
-        DESCRIPTION
-        	"A collection of rate-limit configuration objects on this 
-		interface."
-        INDEX { snPortCARifIndex, snPortCARDirection, snPortCARRowIndex }
-        ::= { snPortCARTable 1 }
-
-SnPortCAREntry ::=
-	SEQUENCE {
-		snPortCARifIndex
-						INTEGER,
-		snPortCARDirection
-               		PacketSource,
-		snPortCARRowIndex
-                        INTEGER,
-		snPortCARType
-                        RateLimitType,
-		snPortCARAccIdx
-                        INTEGER,
-		snPortCARRate
-                        INTEGER,
-		snPortCARLimit
-                        INTEGER,
-		snPortCARExtLimit
-                        INTEGER,
-		snPortCARConformAction
-       					RateLimitAction,
-		snPortCARExceedAction
-       					RateLimitAction,
-		snPortCARStatSwitchedPkts
-                        Counter64,
-		snPortCARStatSwitchedBytes
-                        Counter64,
-		snPortCARStatFilteredPkts
-                        Counter64,
-		snPortCARStatFilteredBytes
-                        Counter64,
-		snPortCARStatCurBurst
-       					Gauge
-	}
-snPortCARifIndex OBJECT-TYPE
-    SYNTAX     INTEGER 
-    ACCESS     read-only
-    STATUS     mandatory
-    DESCRIPTION
-            "The ifIndex value for this rate limit entry."
-    ::= { snPortCAREntry 1 }
-
-snPortCARDirection OBJECT-TYPE
-	SYNTAX  PacketSource
-        ACCESS  read-only
-        STATUS  mandatory
-        DESCRIPTION
-       		"The input or output transmission direction for the 
-                Rate Limit object.
-				input (0), --for inbound traffic
-				output(1) --for outbound traffic "
-        ::= { snPortCAREntry 2 }
-
-snPortCARRowIndex OBJECT-TYPE
-	SYNTAX  INTEGER (1..2147483647)
-        ACCESS  read-only
-        STATUS  mandatory
-        DESCRIPTION
-                "The table index for rate limit objects.
-		It increases as the rate limit entries are added.
-		Skips the number when a row is deleted."
-
-        ::= { snPortCAREntry 3 }
-
-snPortCARType OBJECT-TYPE
-	SYNTAX  RateLimitType
-        ACCESS  read-only
-        STATUS  mandatory
-        DESCRIPTION
-		"The type of traffic rate-limited against."
-
-	::= { snPortCAREntry 4 }
-
-snPortCARAccIdx OBJECT-TYPE
-	SYNTAX  INTEGER
-        ACCESS  read-only
-        STATUS  mandatory
-        DESCRIPTION
-		"The index to the access list if RateLimitType is either
-		quickAcc or standardAcc."
-
-	::= { snPortCAREntry 5 }
-
-snPortCARRate OBJECT-TYPE
-	SYNTAX  INTEGER
-        ACCESS  read-only
-        STATUS  mandatory
-        DESCRIPTION
-		"The comitted access rate. This determines the long term
-		average transmission rate. Traffic that falls under this
-		rate always conforms. This is average rate in bits per 
-		second."
-
-	::= { snPortCAREntry 6 }
-
-snPortCARLimit OBJECT-TYPE
-	SYNTAX  INTEGER
-        ACCESS  read-only
-        STATUS  mandatory
-        DESCRIPTION
-		"This is the normal burst size that determines how large traffic
-		bursts can be before some traffic exceeds the rate limit. This
-		specifies the number of bytes that are guaranteed to be transported
-		by the network at the average rate under normal conditions during
-		committed time interval. This normal burst size is in bytes."
-
-	::= { snPortCAREntry 7 }
-
-snPortCARExtLimit OBJECT-TYPE
-	SYNTAX  INTEGER
-	ACCESS  read-only
-	STATUS  mandatory
-	DESCRIPTION
-		"This is the extended burst limit that determines how large traffic
-		bursts can be before all the traffic exceeds the rate limit. This
-		burst size is in bytes."
-
-	::= { snPortCAREntry 8 }
-
-snPortCARConformAction OBJECT-TYPE
-	SYNTAX	RateLimitAction
-	ACCESS  read-only
-	STATUS	mandatory
-	DESCRIPTION
-		"Action to be taken when the traffic is within
-		the Rate Limit.
-		drop		drop the packet.
-		xmit		transmit the packet.
-		continue	continue to evaluate to the subsequent
-					rate limits.
-		precedXmit	rewrite the IP precedence and transmit
-					the packet.
-		precedCont	rewrite the IP precedence and allow it
-					evaluated by subsequent rate limits."
-
-	::= { snPortCAREntry 9 }
-
-snPortCARExceedAction OBJECT-TYPE
-	SYNTAX	RateLimitAction
-	ACCESS  read-only
-	STATUS	mandatory
-	DESCRIPTION
-		"Action to be taken when the traffic exceeds
-		the Rate Limit.drop		
-		drop the packet.
-		xmit		transmit the packet.
-		continue	continue to evaluate to the subsequent
-					rate limits.
-		precedXmit	rewrite the IP precedence and transmit
-					the packet.
-		precedCont	rewrite the IP precedence and allow it
-					evaluated by subsequent rate limits."
-
-	::= { snPortCAREntry 10 }
-
-snPortCARStatSwitchedPkts OBJECT-TYPE
-	SYNTAX  Counter64
-	ACCESS  read-only
-	STATUS  mandatory
-	DESCRIPTION
-		"The counter of packets permitted by this rate limit."
-
-	::= { snPortCAREntry 11 }
-
-snPortCARStatSwitchedBytes OBJECT-TYPE
-	SYNTAX  Counter64
-	ACCESS  read-only
-	STATUS  mandatory
-	DESCRIPTION
-		"The counter of bytes permitted by this interface."
-
-	::= { snPortCAREntry 12 }
-
-snPortCARStatFilteredPkts OBJECT-TYPE
-	SYNTAX  Counter64
-	--UNITS	"packets"
-	ACCESS  read-only
-	STATUS  mandatory
-	DESCRIPTION
-		"The counter of packets which exceeded this rate limit."
-
-	::= { snPortCAREntry 13 }
-
-snPortCARStatFilteredBytes OBJECT-TYPE
-	SYNTAX  Counter64
-	ACCESS  read-only
-	STATUS  mandatory
-	DESCRIPTION
-		"The counter of bytes which exceeded this rate limit."
-
-	::= { snPortCAREntry 14 }
-
-snPortCARStatCurBurst OBJECT-TYPE
-	SYNTAX  Gauge
-	ACCESS  read-only
-	STATUS  mandatory
-	DESCRIPTION
-		"The current received burst size."
-	::= { snPortCAREntry 15 }
-
--- end of snPortCARTable
-
-
-END
+FOUNDRY-CAR-MIB DEFINITIONS ::= BEGIN
+
+IMPORTS
+
+	MODULE-IDENTITY, OBJECT-TYPE,Gauge32, Counter64,Integer32
+		FROM SNMPv2-SMI
+	TEXTUAL-CONVENTION
+		FROM SNMPv2-TC
+	snSwitch
+		FROM FOUNDRY-SN-SWITCH-GROUP-MIB
+	InterfaceIndex, ifIndex
+		FROM IF-MIB;
+
+snCAR MODULE-IDENTITY
+    LAST-UPDATED "201006020000Z"  -- 04 June 2010
+    ORGANIZATION "Brocade Communications Systems, Inc."
+    CONTACT-INFO
+             "Technical Support Center
+              130 Holger Way,
+              San Jose, CA  95134
+              Email:  ipsupport@brocade.com
+              Phone: 1-800-752-8061
+              URL:  www.brocade.com"
+    DESCRIPTION
+             "Copyright 1996-2010 Brocade Communications Systems, Inc.
+              All rights reserved.
+              This Brocade Communications Systems SNMP Management Information Base Specification
+              embodies Brocade Communications Systems' confidential and proprietary
+              intellectual property. Brocade Communications Systems retains all
+              title and ownership in the Specification, including any revisions.
+
+              This Specification is supplied AS IS, and Brocade Communications Systems makes
+              no warranty, either express or implied, as to the use,
+              operation, condition, or performance of the specification, and any unintended
+              consequence it may on the user environment."
+
+    REVISION        "201006020000Z"  -- 04 June 2010
+    DESCRIPTION
+        "Changed the ORGANIZATION, CONTACT-INFO and DESCRIPTION fields."
+
+    REVISION     "200909300000Z" -- September 30, 2009
+    DESCRIPTION
+			"convert from SMIv1 to SMIv2"
+
+   ::= { snSwitch 16}
+snPortCARs	OBJECT IDENTIFIER ::= { snCAR 1 }
+
+	--  Textual Conventions
+
+	PacketSource::= TEXTUAL-CONVENTION
+	STATUS      current
+	DESCRIPTION
+		"
+		"
+	SYNTAX  INTEGER {
+		input(0), --for inbound traffic
+		output(1) --for outbound traffic
+	}
+
+
+	RateLimitType::= TEXTUAL-CONVENTION
+	STATUS      current
+	DESCRIPTION
+		"
+		"
+	SYNTAX   INTEGER{
+		all(3), 		--	all traffic.
+		quickAcc(2), 	--	traffic matches rate-limit's access list.
+		standardAcc(1) 	--	traffic matches standard access list.
+	}
+
+	RateLimitAction::= TEXTUAL-CONVENTION
+	STATUS      current
+	DESCRIPTION
+		"
+		"
+	SYNTAX  INTEGER {
+		continue(1),
+		drop(2),
+		precedCont(3),
+		precedXmit(4),
+		xmit(5)
+	}
+
+
+snPortCARTable OBJECT-TYPE
+	SYNTAX  SEQUENCE OF SnPortCAREntry
+	MAX-ACCESS  not-accessible
+		STATUS  current
+		DESCRIPTION
+		"A table of rate limit configuration entries.
+	Rate Limit is a method of traffic control.  It allows a set
+	of rate limits to be configured and applied to packets flowing
+	into/out of an interface to regulate network traffic."
+
+		::= { snPortCARs 1 }
+
+snPortCAREntry OBJECT-TYPE
+		SYNTAX SnPortCAREntry
+		MAX-ACCESS  not-accessible
+		STATUS  current
+		DESCRIPTION
+			"A collection of rate-limit configuration objects on this
+		interface."
+		INDEX { snPortCARifIndex, snPortCARDirection, snPortCARRowIndex }
+		::= { snPortCARTable 1 }
+
+SnPortCAREntry ::=
+	SEQUENCE {
+		snPortCARifIndex
+						InterfaceIndex,
+		snPortCARDirection
+					PacketSource,
+		snPortCARRowIndex
+						INTEGER,
+		snPortCARType
+						RateLimitType,
+		snPortCARAccIdx
+						Integer32,
+		snPortCARRate
+						Integer32,
+		snPortCARLimit
+						Integer32,
+		snPortCARExtLimit
+						Integer32,
+		snPortCARConformAction
+						RateLimitAction,
+		snPortCARExceedAction
+						RateLimitAction,
+		snPortCARStatSwitchedPkts
+						Counter64,
+		snPortCARStatSwitchedBytes
+						Counter64,
+		snPortCARStatFilteredPkts
+						Counter64,
+		snPortCARStatFilteredBytes
+						Counter64,
+		snPortCARStatCurBurst
+						Gauge32
+	}
+snPortCARifIndex OBJECT-TYPE
+	SYNTAX     InterfaceIndex
+	MAX-ACCESS     read-only
+	STATUS     current
+	DESCRIPTION
+			"The ifIndex value for this rate limit entry."
+	::= { snPortCAREntry 1 }
+
+snPortCARDirection OBJECT-TYPE
+	SYNTAX  PacketSource
+		MAX-ACCESS  read-only
+		STATUS  current
+		DESCRIPTION
+			"The input or output transmission direction for the
+				Rate Limit object.
+				input (0), --for inbound traffic
+				output(1) --for outbound traffic "
+		::= { snPortCAREntry 2 }
+
+snPortCARRowIndex OBJECT-TYPE
+	SYNTAX  INTEGER (1..2147483647)
+		MAX-ACCESS  read-only
+		STATUS  current
+		DESCRIPTION
+				"The table index for rate limit objects.
+		It increases as the rate limit entries are added.
+		Skips the number when a row is deleted."
+
+		::= { snPortCAREntry 3 }
+
+snPortCARType OBJECT-TYPE
+	SYNTAX  RateLimitType
+		MAX-ACCESS  read-only
+		STATUS  current
+		DESCRIPTION
+		"The type of traffic rate-limited against."
+
+	::= { snPortCAREntry 4 }
+
+snPortCARAccIdx OBJECT-TYPE
+	SYNTAX  Integer32
+		MAX-ACCESS  read-only
+		STATUS  current
+		DESCRIPTION
+		"The index to the access list if RateLimitType is either
+		quickAcc or standardAcc."
+
+	::= { snPortCAREntry 5 }
+
+snPortCARRate OBJECT-TYPE
+	SYNTAX  Integer32
+		MAX-ACCESS  read-only
+		STATUS  current
+		DESCRIPTION
+		"The comitted access rate. This determines the long term
+		average transmission rate. Traffic that falls under this
+		rate always conforms. This is average rate in bits per
+		second."
+
+	::= { snPortCAREntry 6 }
+
+snPortCARLimit OBJECT-TYPE
+	SYNTAX  Integer32
+		MAX-ACCESS  read-only
+		STATUS  current
+		DESCRIPTION
+		"This is the normal burst size that determines how large traffic
+		bursts can be before some traffic exceeds the rate limit. This
+		specifies the number of bytes that are guaranteed to be transported
+		by the network at the average rate under normal conditions during
+		committed time interval. This normal burst size is in bytes."
+
+	::= { snPortCAREntry 7 }
+
+snPortCARExtLimit OBJECT-TYPE
+	SYNTAX  Integer32
+	MAX-ACCESS  read-only
+	STATUS  current
+	DESCRIPTION
+		"This is the extended burst limit that determines how large traffic
+		bursts can be before all the traffic exceeds the rate limit. This
+		burst size is in bytes."
+
+	::= { snPortCAREntry 8 }
+
+snPortCARConformAction OBJECT-TYPE
+	SYNTAX	RateLimitAction
+	MAX-ACCESS  read-only
+	STATUS	current
+	DESCRIPTION
+		"Action to be taken when the traffic is within
+		the Rate Limit.
+		drop		drop the packet.
+		xmit		transmit the packet.
+		continue	continue to evaluate to the subsequent
+					rate limits.
+		precedXmit	rewrite the IP precedence and transmit
+					the packet.
+		precedCont	rewrite the IP precedence and allow it
+					evaluated by subsequent rate limits."
+
+	::= { snPortCAREntry 9 }
+
+snPortCARExceedAction OBJECT-TYPE
+	SYNTAX	RateLimitAction
+	MAX-ACCESS  read-only
+	STATUS	current
+	DESCRIPTION
+		"Action to be taken when the traffic exceeds
+		the Rate Limit.drop
+		drop the packet.
+		xmit		transmit the packet.
+		continue	continue to evaluate to the subsequent
+					rate limits.
+		precedXmit	rewrite the IP precedence and transmit
+					the packet.
+		precedCont	rewrite the IP precedence and allow it
+					evaluated by subsequent rate limits."
+
+	::= { snPortCAREntry 10 }
+
+snPortCARStatSwitchedPkts OBJECT-TYPE
+	SYNTAX  Counter64
+	MAX-ACCESS  read-only
+	STATUS  current
+	DESCRIPTION
+		"The counter of packets permitted by this rate limit."
+
+	::= { snPortCAREntry 11 }
+
+snPortCARStatSwitchedBytes OBJECT-TYPE
+	SYNTAX  Counter64
+	MAX-ACCESS  read-only
+	STATUS  current
+	DESCRIPTION
+		"The counter of bytes permitted by this interface."
+
+	::= { snPortCAREntry 12 }
+
+snPortCARStatFilteredPkts OBJECT-TYPE
+	SYNTAX  Counter64
+	--UNITS	"packets"
+	MAX-ACCESS  read-only
+	STATUS  current
+	DESCRIPTION
+		"The counter of packets which exceeded this rate limit."
+
+	::= { snPortCAREntry 13 }
+
+snPortCARStatFilteredBytes OBJECT-TYPE
+	SYNTAX  Counter64
+	MAX-ACCESS  read-only
+	STATUS  current
+	DESCRIPTION
+		"The counter of bytes which exceeded this rate limit."
+
+	::= { snPortCAREntry 14 }
+
+snPortCARStatCurBurst OBJECT-TYPE
+	SYNTAX  Gauge32
+	MAX-ACCESS  read-only
+	STATUS  current
+	DESCRIPTION
+		"The current received burst size."
+	::= { snPortCAREntry 15 }
+
+-- end of snPortCARTable
+
+-- RL Counter Table
+
+agRateLimitCounterTable OBJECT-TYPE
+	SYNTAX		SEQUENCE OF AgRateLimitCounterEntry
+	MAX-ACCESS		not-accessible
+	STATUS		current
+	DESCRIPTION
+	"A table of rate limit counter entries."
+	::= { snPortCARs 2 }
+
+agRateLimitCounterEntry OBJECT-TYPE
+	SYNTAX		AgRateLimitCounterEntry
+	MAX-ACCESS		not-accessible
+	STATUS		current
+	DESCRIPTION
+	"A collection of rate-limit counter objects on a
+	interface, direction and configuration row index within that interface."
+	INDEX { ifIndex, snPortCARRowIndex }
+	::= { agRateLimitCounterTable 1 }
+
+AgRateLimitCounterEntry ::=
+	SEQUENCE {
+		agRateLimitCounterFwdedOctets
+			Counter64,
+		agRateLimitCounterDroppedOctets
+			Counter64,
+		agRateLimitCounterReMarkedOctets
+			Counter64,
+		agRateLimitCounterTotalOctets
+			Counter64
+	}
+
+agRateLimitCounterFwdedOctets OBJECT-TYPE
+	SYNTAX	Counter64
+	MAX-ACCESS	read-only
+	STATUS	current
+	DESCRIPTION
+	"The forwarded octet count for this rate limit entry."
+	::= { agRateLimitCounterEntry 1 }
+
+agRateLimitCounterDroppedOctets OBJECT-TYPE
+	SYNTAX	Counter64
+	MAX-ACCESS	read-only
+	STATUS	current
+	DESCRIPTION
+	"The dropped octet count for this rate limit entry."
+	::= { agRateLimitCounterEntry 2 }
+
+agRateLimitCounterReMarkedOctets OBJECT-TYPE
+	SYNTAX	Counter64
+	MAX-ACCESS	read-only
+	STATUS	current
+	DESCRIPTION
+	"The remarked octet count for this rate limit entry."
+	::= { agRateLimitCounterEntry 3 }
+
+agRateLimitCounterTotalOctets OBJECT-TYPE
+	SYNTAX	Counter64
+	MAX-ACCESS	read-only
+	STATUS	current
+	DESCRIPTION
+	"The total octet count for this rate limit entry."
+	::= { agRateLimitCounterEntry 4 }
+
+END
+-- *****************************************************************
+-- Foundry Commited Access Rate MIB file.
+-- *****************************************************************

mibs/FOUNDRY-LAG-MIB

@@ -0,0 +1,293 @@
+FOUNDRY-LAG-MIB DEFINITIONS ::= BEGIN
+
+IMPORTS
+    MODULE-IDENTITY, OBJECT-TYPE, Unsigned32
+      FROM SNMPv2-SMI			-- [RFC2578]
+    InterfaceIndex, ifIndex, InterfaceIndexOrZero
+      FROM IF-MIB				-- [RFC2863]
+    DisplayString, RowStatus
+      FROM SNMPv2-TC			-- [RFC2579]
+    snSwitch, snTraps
+      FROM FOUNDRY-SN-ROOT-MIB;
+
+fdryLinkAggregationGroupMIB MODULE-IDENTITY
+    LAST-UPDATED "201006020000Z"  -- 04 June 2010
+    ORGANIZATION "Brocade Communications Systems, Inc."
+    CONTACT-INFO
+             "Technical Support Center
+              130 Holger Way,
+              San Jose, CA  95134
+              Email:  ipsupport@brocade.com
+              Phone: 1-800-752-8061
+              URL:  www.brocade.com"
+    DESCRIPTION
+	      "Management Information Base module for link aggregate group
+              configuration and statistics. Link aggregation group is a new concept
+              of trunk and this MIB is replacing FOUNDRY-SN-LAG-MIB in MLX/XMR products
+		starting release 4.1.0.
+
+              Copyright 1996-2010 Brocade Communications Systems, Inc.
+              All rights reserved.
+              This Brocade Communications Systems SNMP Management Information Base Specification
+              embodies Brocade Communications Systems' confidential and proprietary
+              intellectual property. Brocade Communications Systems retains all
+              title and ownership in the Specification, including any revisions.
+
+              This Specification is supplied AS IS, and Brocade Communications Systems makes
+              no warranty, either express or implied, as to the use,
+              operation, condition, or performance of the specification, and any unintended
+              consequence it may on the user environment."
+
+    REVISION        "201006020000Z"  -- 04 June 2010
+    DESCRIPTION
+        "Changed the ORGANIZATION, CONTACT-INFO and DESCRIPTION fields."
+
+    REVISION     "200909300000Z" -- September 30, 2009
+    DESCRIPTION
+			"convert from SMIv1 to SMIv2"
+
+   ::= { snSwitch 33 }
+
+fdryLinkAggregationGroupNotifyObjects  OBJECT IDENTIFIER ::= { fdryLinkAggregationGroupMIB 0 }
+fdryLinkAggregationGroupTableObjects  OBJECT IDENTIFIER ::= { fdryLinkAggregationGroupMIB 1 }
+fdryLinkAggregationGroupPortTableObjects  OBJECT IDENTIFIER ::= { fdryLinkAggregationGroupMIB 2 }
+
+-- LinkAggregationGroup Global Scalar Object Section
+
+-- LinkAggregationGroup Table Object Section
+
+--
+-- LinkAggregationGroup Table
+--
+
+fdryLinkAggregationGroupTable OBJECT-TYPE
+    SYNTAX     SEQUENCE OF FdryLinkAggregationGroupEntry
+    MAX-ACCESS not-accessible
+    STATUS     current
+    DESCRIPTION
+            "LinkAggregationGroup table."
+    ::= { fdryLinkAggregationGroupTableObjects 1 }
+
+fdryLinkAggregationGroupEntry OBJECT-TYPE
+    SYNTAX     FdryLinkAggregationGroupEntry
+    MAX-ACCESS not-accessible
+    STATUS     current
+    DESCRIPTION
+            "An entry of the Link Aggregate Group table."
+    INDEX { fdryLinkAggregationGroupName }
+    ::= { fdryLinkAggregationGroupTable 1 }
+
+FdryLinkAggregationGroupEntry ::= SEQUENCE {
+    fdryLinkAggregationGroupName                 DisplayString,
+    fdryLinkAggregationGroupType                  INTEGER,
+    fdryLinkAggregationGroupAdminStatus       INTEGER,
+    fdryLinkAggregationGroupIfList                  OCTET STRING,
+    fdryLinkAggregationGroupPrimaryPort        InterfaceIndex,
+    fdryLinkAggregationGroupTrunkType          INTEGER,
+    fdryLinkAggregationGroupTrunkThreshold   Unsigned32,
+    fdryLinkAggregationGroupLacpTimeout       INTEGER,
+    fdryLinkAggregationGroupIfIndex              InterfaceIndexOrZero,
+    fdryLinkAggregationGroupPortCount           Unsigned32,
+    fdryLinkAggregationGroupRowStatus          RowStatus,
+    fdryLinkAggregationGroupId                      Unsigned32
+}
+
+fdryLinkAggregationGroupName OBJECT-TYPE
+    SYNTAX     DisplayString (SIZE(1..64))
+    MAX-ACCESS not-accessible
+    STATUS     current
+    DESCRIPTION
+            "Name of a LinkAggregationGroup."
+    ::= { fdryLinkAggregationGroupEntry 1 }
+
+fdryLinkAggregationGroupType OBJECT-TYPE
+    SYNTAX     INTEGER { static(1), dynamic(2), keepalive(3) }
+    MAX-ACCESS read-create
+    STATUS     current
+    DESCRIPTION
+            "LinkAggregationGroup type."
+    ::= { fdryLinkAggregationGroupEntry 2 }
+
+fdryLinkAggregationGroupAdminStatus OBJECT-TYPE
+    SYNTAX     INTEGER { deploy(1), deployPassive(2), undeploy(3), undeployForced(4) }
+    MAX-ACCESS read-create
+    STATUS     current
+    DESCRIPTION
+         "The desired deplyed state of this LinkAggregationGroup entry.
+         This is not the operational status. Refer to ifTable for the
+         operational status.
+         deploy(1).............deploy the LAG and set to LACP active if dynamic LAG.
+         deployPassive(2)..deploy the LAG and set to LACP passive if dynamic LAG.
+         undeploy(3).........undeploy the LAG if no more than 2 ports are enabled.
+         undeployForced(4)..undeploy the LAG regardless number of ports enabled.
+                                      This is a write-only value.
+         In particular, a row cannot be deployed until the corresponding
+         instances of fdryLinkAggregationGroupIfList has been set."
+    ::= { fdryLinkAggregationGroupEntry 3 }
+
+fdryLinkAggregationGroupIfList OBJECT-TYPE
+    SYNTAX  OCTET STRING
+    MAX-ACCESS read-create
+    STATUS     current
+    DESCRIPTION
+            "A list of interface indices which are the port membership
+            of a trunk group. Each interface index is a 32-bit integer
+            in big endian order."
+    ::= { fdryLinkAggregationGroupEntry 4 }
+
+fdryLinkAggregationGroupPrimaryPort OBJECT-TYPE
+    SYNTAX     InterfaceIndex
+    MAX-ACCESS read-create
+    STATUS     current
+    DESCRIPTION
+            "The primary port for the Link Aggregation Group. This must
+            be set before deploying the LinkAggregateGroup unless this is
+            a keepalive LinkAggregateGroup."
+    ::= { fdryLinkAggregationGroupEntry 5 }
+
+fdryLinkAggregationGroupTrunkType OBJECT-TYPE
+    SYNTAX     INTEGER { hashBased(1), perPacket(2) }
+    MAX-ACCESS read-create
+    STATUS     current
+    DESCRIPTION
+            "The trunk connection type which specifies what the scheme
+            of load-sharing among the trunk ports is."
+    ::= { fdryLinkAggregationGroupEntry 6 }
+
+fdryLinkAggregationGroupTrunkThreshold OBJECT-TYPE
+    SYNTAX     Unsigned32
+    MAX-ACCESS read-create
+    STATUS     current
+    DESCRIPTION
+            "The number of UP ports needed to keep the trunk up.
+            Not applicable for keepalive LAG."
+    ::= { fdryLinkAggregationGroupEntry 7 }
+
+fdryLinkAggregationGroupLacpTimeout OBJECT-TYPE
+    SYNTAX     INTEGER { default(1), long(2), short(3) }
+    MAX-ACCESS read-create
+    STATUS     current
+    DESCRIPTION
+            "The LACP timeout value this LACP LAG will use. Applicable for
+            dynamic and keepalive LAG only."
+    ::= { fdryLinkAggregationGroupEntry 8 }
+
+fdryLinkAggregationGroupIfIndex OBJECT-TYPE
+    SYNTAX     InterfaceIndexOrZero
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+            "After deployment the operation information of a LAG entry will be
+            represented in an entry in ifTable. Use this variable as the ifIndex
+            to access the entry in ifTable and ifXTable. Zero will be returned
+            for LAGs not yet deployed."
+    ::= { fdryLinkAggregationGroupEntry 9 }
+
+fdryLinkAggregationGroupPortCount OBJECT-TYPE
+    SYNTAX     Unsigned32
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+            "The number of member ports belong to this LAG."
+    ::= { fdryLinkAggregationGroupEntry 10 }
+
+fdryLinkAggregationGroupRowStatus OBJECT-TYPE
+    SYNTAX      RowStatus
+    MAX-ACCESS  read-create
+    STATUS      current
+    DESCRIPTION
+        "The status of this conceptual row.
+
+        createAndWait(5) is not supported.
+
+        To create a row in this table, a manager must
+        set this object to createAndGo(4) together with the setting of
+        fdryLinkAggregationGroupType. After that the row status becomes
+        active(1) regardless the LAG entry is deployed or not.
+
+        To deploy the LAG entry, set the corresponding instance of
+        fdryLinkAggregationGroupAdminStatus to deployActive or deployPassive."
+    ::= { fdryLinkAggregationGroupEntry 11 }
+
+fdryLinkAggregationGroupId OBJECT-TYPE
+    SYNTAX     Unsigned32
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+            "The numeric identifier assigned to this LAG."
+    ::= { fdryLinkAggregationGroupEntry 12 }
+
+--
+-- LinkAggregationGroupPort Table
+--
+
+fdryLinkAggregationGroupPortTable OBJECT-TYPE
+    SYNTAX     SEQUENCE OF FdryLinkAggregationGroupPortEntry
+    MAX-ACCESS not-accessible
+    STATUS     current
+    DESCRIPTION
+            "A table that contains Link Aggregation Control
+            configuration information about every
+            Aggregation Port associated with this device.
+            A row appears in this table for each physical port."
+    ::= { fdryLinkAggregationGroupPortTableObjects 1 }
+
+fdryLinkAggregationGroupPortEntry OBJECT-TYPE
+    SYNTAX     FdryLinkAggregationGroupPortEntry
+    MAX-ACCESS not-accessible
+    STATUS     current
+    DESCRIPTION
+            "An entry of the Link Aggregate Group Port table."
+    INDEX { fdryLinkAggregationGroupName, ifIndex }
+    ::= { fdryLinkAggregationGroupPortTable 1 }
+
+FdryLinkAggregationGroupPortEntry ::= SEQUENCE {
+    fdryLinkAggregationGroupPortLacpPriority   INTEGER
+}
+
+fdryLinkAggregationGroupPortLacpPriority OBJECT-TYPE
+    SYNTAX     INTEGER (0..65535)
+    MAX-ACCESS read-write
+    STATUS     current
+    DESCRIPTION
+            "The LACP priority value assigned to this link aggregation port. Applicable
+            for dynamic and keepalive LAG only."
+    DEFVAL { 1 }
+    ::= { fdryLinkAggregationGroupPortEntry 1 }
+
+fdryLAGName OBJECT-TYPE
+    SYNTAX     DisplayString (SIZE(1..64))
+    MAX-ACCESS accessible-for-notify
+    STATUS     current
+    DESCRIPTION
+            "Name of a LinkAggregationGroup."
+    ::= { fdryLinkAggregationGroupNotifyObjects 1 }
+
+fdryTrapLagDeployed NOTIFICATION-TYPE
+   OBJECTS { fdryLAGName,
+                    fdryLinkAggregationGroupIfIndex }
+   STATUS current
+   DESCRIPTION
+            "The SNMP trap that is generated when a LAG is deployed."
+   --#TYPE "Foundry Trap: LAG deployed"
+   --#SUMMARY "LAG %s deployed"
+   --#ARGUMENTS { 0 }
+   --#SEVERITY INFORMATIONAL
+   --#STATE OPERATIONAL
+   ::= { snTraps 1204 }
+
+fdryTrapLagUndeployed NOTIFICATION-TYPE
+   OBJECTS { fdryLAGName,
+                    fdryLinkAggregationGroupIfIndex }
+   STATUS current
+   DESCRIPTION
+            "The SNMP trap that is generated when a LAG is undeployed."
+   --#TYPE "Foundry Trap: LAG undeployed"
+   --#SUMMARY "LAG %s undeployed"
+   --#ARGUMENTS { 0 }
+   --#SEVERITY INFORMATIONAL
+   --#STATE OPERATIONAL
+   ::= { snTraps 1205 }
+
+
+END

mibs/FOUNDRY-MAC-VLAN-MIB

@@ -0,0 +1,275 @@
+FOUNDRY-MAC-VLAN-MIB DEFINITIONS ::= BEGIN
+
+IMPORTS
+    MODULE-IDENTITY, OBJECT-TYPE, Integer32
+      FROM SNMPv2-SMI
+    MacAddress, RowStatus
+      FROM SNMPv2-TC
+    InterfaceIndex
+      FROM IF-MIB;
+
+
+fdryMacVlanMIB MODULE-IDENTITY
+    LAST-UPDATED "201006020000Z"  -- 04 June 2010
+    ORGANIZATION "Brocade Communications Systems, Inc."
+    CONTACT-INFO
+             "Technical Support Center
+              130 Holger Way,
+              San Jose, CA  95134
+              Email:  ipsupport@brocade.com
+              Phone: 1-800-752-8061
+              URL:  www.brocade.com"
+    DESCRIPTION
+             "Management Information Base module for MAC-based VLAN
+              configuration and statistics.
+
+              Copyright 1996-2010 Brocade Communications Systems, Inc.
+              All rights reserved.
+              This Brocade Communications Systems SNMP Management Information Base Specification
+              embodies Brocade Communications Systems' confidential and proprietary
+              intellectual property. Brocade Communications Systems retains all
+              title and ownership in the Specification, including any revisions.
+
+              This Specification is supplied AS IS, and Brocade Communications Systems makes
+              no warranty, either express or implied, as to the use,
+              operation, condition, or performance of the specification, and any unintended
+              consequence it may on the user environment."
+
+    REVISION        "201006020000Z"  -- 04 June 2010
+    DESCRIPTION
+        "Changed the ORGANIZATION, CONTACT-INFO and DESCRIPTION fields."
+
+    REVISION     "200812170000Z" -- 17 December 2008
+    DESCRIPTION
+            "Replaces earlier snMacVlan MIB."
+   ::= { iso(1) org(3) dod(6) internet(1) private(4) enterprises(1) foundry(1991) products(1) switch(1) snSwitch(3) 32 }
+
+
+--
+-- Mac-based VLAN
+--
+
+fdryMacVlanGlobalObjects OBJECT IDENTIFIER ::= { fdryMacVlanMIB 1 }
+fdryMacVlanTableObjects  OBJECT IDENTIFIER ::= { fdryMacVlanMIB 2 }
+
+--
+-- MAC-based VLAN Global Scalar Object Section
+--
+
+fdryMacVlanGlobalClearOper OBJECT-TYPE
+    SYNTAX     INTEGER { valid(0), clear(1) }
+    MAX-ACCESS read-write
+    STATUS     current
+    DESCRIPTION
+        "valid(0) - this value is always returned when the variable is read.
+         clear(1) - setting the variable to this value clears the operational
+                    MAC-based VLAN information for all ports."
+    ::= { fdryMacVlanGlobalObjects 1 }
+
+fdryMacVlanGlobalDynConfigState OBJECT-TYPE
+    SYNTAX     INTEGER { disabled(0), enabled(1) }
+    MAX-ACCESS read-write
+    STATUS     current
+    DESCRIPTION
+        "Enable/disable MAC-based VLAN dynamic activation on the global level."
+    ::= { fdryMacVlanGlobalObjects 2}
+
+--
+-- MAC-based VLAN Table Object Section
+--
+
+--
+-- MAC-based VLAN Port Membership Table
+-- Use this table to add or remove ports for MAC-based VLANs
+--
+
+fdryMacVlanPortMemberTable OBJECT-TYPE
+    SYNTAX     SEQUENCE OF FdryMacVlanPortMemberEntry
+    MAX-ACCESS not-accessible
+    STATUS     current
+    DESCRIPTION
+        "MAC-based VLAN port membership table."
+    ::= { fdryMacVlanTableObjects 1 }
+
+fdryMacVlanPortMemberEntry OBJECT-TYPE
+    SYNTAX     FdryMacVlanPortMemberEntry
+    MAX-ACCESS not-accessible
+    STATUS     current
+    DESCRIPTION
+        "An entry of the MAC-based VLAN port membership table."
+    INDEX { fdryMacVlanPortMemberVLanId, fdryMacVlanPortMemberPortId }
+    ::= { fdryMacVlanPortMemberTable 1 }
+
+FdryMacVlanPortMemberEntry ::= SEQUENCE {
+    fdryMacVlanPortMemberVLanId      INTEGER,
+    fdryMacVlanPortMemberPortId      InterfaceIndex,
+    fdryMacVlanPortMemberRowStatus   RowStatus
+}
+
+fdryMacVlanPortMemberVLanId OBJECT-TYPE
+    SYNTAX    INTEGER (1..4095)
+    MAX-ACCESS not-accessible
+    STATUS     current
+    DESCRIPTION
+        "The VLAN identifier (VLAN ID)."
+    ::= { fdryMacVlanPortMemberEntry 1 }
+
+fdryMacVlanPortMemberPortId OBJECT-TYPE
+    SYNTAX     InterfaceIndex
+    MAX-ACCESS not-accessible
+    STATUS     current
+    DESCRIPTION
+        "The ifIndex of the port which is a member of the MAC-based VLAN."
+    ::= { fdryMacVlanPortMemberEntry 2 }
+
+fdryMacVlanPortMemberRowStatus OBJECT-TYPE
+    SYNTAX     RowStatus
+    MAX-ACCESS read-create
+    STATUS     current
+    DESCRIPTION
+        "This object is used to create and delete rows in the table."
+    ::= { fdryMacVlanPortMemberEntry 3 }
+
+--
+-- MAC-based VLAN Interface Table Object Section
+--
+
+fdryMacVlanIfTable OBJECT-TYPE
+    SYNTAX     SEQUENCE OF FdryMacVlanIfEntry
+    MAX-ACCESS not-accessible
+    STATUS     current
+    DESCRIPTION
+        "MAC-based VLAN Interface table."
+    ::= { fdryMacVlanTableObjects 2 }
+
+fdryMacVlanIfEntry OBJECT-TYPE
+    SYNTAX     FdryMacVlanIfEntry
+    MAX-ACCESS not-accessible
+    STATUS     current
+    DESCRIPTION
+        "An entry in the MAC-based VLAN interface table."
+    INDEX { fdryMacVlanIfIndex }
+    ::= { fdryMacVlanIfTable 1 }
+
+FdryMacVlanIfEntry ::= SEQUENCE {
+    fdryMacVlanIfIndex            InterfaceIndex,
+    fdryMacVlanIfEnable           INTEGER,
+    fdryMacVlanIfMaxEntry         Integer32,
+    fdryMacVlanIfClearOper        INTEGER,
+    fdryMacVlanIfClearConfig      INTEGER
+}
+
+fdryMacVlanIfIndex OBJECT-TYPE
+    SYNTAX     InterfaceIndex
+    MAX-ACCESS not-accessible
+    STATUS     current
+    DESCRIPTION
+        "The ifIndex of the interface which is a member of the MAC-based VLAN."
+    ::= { fdryMacVlanIfEntry 1 }
+
+fdryMacVlanIfEnable OBJECT-TYPE
+    SYNTAX     INTEGER { disabled(0), enabled(1) }
+    MAX-ACCESS read-write
+    STATUS     current
+    DESCRIPTION
+        "The administrative status requested by management for
+    MAC-based VLANs on this interface.  The value enabled(1)
+    indicates that MAC-based VLANs should be enabled on this interface,
+    When disabled(2), MAC-based VLANs are disabled on this interface.
+    Enable/disable MAC-based VLAN on this interface."
+    ::= { fdryMacVlanIfEntry 2 }
+
+fdryMacVlanIfMaxEntry OBJECT-TYPE
+    SYNTAX     Integer32 (2..32)
+    MAX-ACCESS read-write
+    STATUS     current
+    DESCRIPTION
+        "The maximum number of allowed and denied MAC address
+        (static and dynamic) that can be leared on this interface.
+        The default value is 2. The value should be between 2 to 32."
+    DEFVAL      { 2 }
+    ::= { fdryMacVlanIfEntry 3 }
+
+fdryMacVlanIfClearOper OBJECT-TYPE
+    SYNTAX      INTEGER { valid(0), clear(1) }
+    MAX-ACCESS  read-write
+    STATUS      current
+    DESCRIPTION
+        "valid(0) - this value is always returned when the variable is read.
+         clear(1) - setting the variable to this value clears the operational
+                    MAC-based VLAN information for a port."
+    ::= { fdryMacVlanIfEntry 4 }
+
+fdryMacVlanIfClearConfig OBJECT-TYPE
+    SYNTAX      INTEGER { valid(0), clear(1) }
+    MAX-ACCESS  read-write
+    STATUS      current
+    DESCRIPTION
+        "valid(0) - this value is always returned when the variable is read.
+         clear(1) - setting the variable to this value clears the configured
+                    MAC-based VLAN information for a port."
+    ::= { fdryMacVlanIfEntry 5 }
+
+--
+-- MAC-based VLAN Table Object section
+--
+
+fdryMacBasedVlanTable OBJECT-TYPE
+    SYNTAX     SEQUENCE OF FdryMacBasedVlanEntry
+    MAX-ACCESS not-accessible
+    STATUS     current
+    DESCRIPTION
+        "MAC-based VLAN table."
+    ::= { fdryMacVlanTableObjects 3 }
+
+fdryMacBasedVlanEntry OBJECT-TYPE
+    SYNTAX     FdryMacBasedVlanEntry
+    MAX-ACCESS not-accessible
+    STATUS     current
+    DESCRIPTION
+        "An entry in the MAC-based VLAN table."
+    INDEX { fdryMacVlanIfIndex, fdryMacBasedVlanId, fdryMacBasedVlanMac }
+    ::= { fdryMacBasedVlanTable 1 }
+
+FdryMacBasedVlanEntry ::= SEQUENCE {
+    fdryMacBasedVlanId                INTEGER,
+    fdryMacBasedVlanMac               MacAddress,
+    fdryMacBasedVlanPriority          Integer32,
+    fdryMacBasedVlanRowStatus         RowStatus
+}
+
+fdryMacBasedVlanId OBJECT-TYPE
+    SYNTAX     INTEGER (1..4095)
+    MAX-ACCESS not-accessible
+    STATUS     current
+    DESCRIPTION
+        "The VLAN ID for this entry."
+    ::= { fdryMacBasedVlanEntry 1 }
+
+fdryMacBasedVlanMac OBJECT-TYPE
+    SYNTAX     MacAddress
+    MAX-ACCESS not-accessible
+    STATUS     current
+    DESCRIPTION
+        "A host source MAC address to be authenticated."
+    ::= { fdryMacBasedVlanEntry 2 }
+
+fdryMacBasedVlanPriority OBJECT-TYPE
+    SYNTAX     Integer32 (0..7)
+    MAX-ACCESS read-create
+    STATUS     current
+    DESCRIPTION
+        "The priority of the source MAC address."
+    ::= { fdryMacBasedVlanEntry 3 }
+
+fdryMacBasedVlanRowStatus OBJECT-TYPE
+    SYNTAX     RowStatus
+    MAX-ACCESS read-create
+    STATUS     current
+    DESCRIPTION
+            "This object is used to create and delete rows in the table."
+    ::= { fdryMacBasedVlanEntry 4 }
+
+END
+
+

mibs/FOUNDRY-SN-ARP-GROUP-MIB

@@ -0,0 +1,109 @@
+FOUNDRY-SN-ARP-GROUP-MIB DEFINITIONS ::= BEGIN
+
+-- SECTION 1: Top Level Definitions
+-- Imports
+
+IMPORTS
+
+MODULE-IDENTITY, OBJECT-TYPE, Counter32
+		FROM SNMPv2-SMI
+snSwitch
+		FROM FOUNDRY-SN-ROOT-MIB;
+
+snArpInfo MODULE-IDENTITY
+    LAST-UPDATED "201006020000Z"  -- 04 June 2010
+    ORGANIZATION "Brocade Communications Systems, Inc."
+    CONTACT-INFO
+             "Technical Support Center
+              130 Holger Way,
+              San Jose, CA  95134
+              Email:  ipsupport@brocade.com
+              Phone: 1-800-752-8061
+              URL:  www.brocade.com"
+    DESCRIPTION
+             "The Enterprise MIB for ARP support in SNMP.
+
+              Copyright 1996-2010 Brocade Communications Systems, Inc.
+              All rights reserved.
+              This Brocade Communications Systems SNMP Management Information Base Specification
+              embodies Brocade Communications Systems' confidential and proprietary
+              intellectual property. Brocade Communications Systems retains all
+              title and ownership in the Specification, including any revisions.
+
+              This Specification is supplied AS IS, and Brocade Communications Systems makes
+              no warranty, either express or implied, as to the use,
+              operation, condition, or performance of the specification, and any unintended
+              consequence it may on the user environment."
+
+    REVISION        "201006020000Z"  -- 04 June 2010
+    DESCRIPTION
+        "Changed the ORGANIZATION, CONTACT-INFO and DESCRIPTION fields."
+
+       ::= { snSwitch 22 }
+
+snArpStats                    OBJECT IDENTIFIER ::= { snArpInfo 1 }
+
+snArpStatsTotalReceived OBJECT-TYPE
+    SYNTAX         Counter32
+    MAX-ACCESS  read-only
+    STATUS         current
+    DESCRIPTION
+            "The total number of ARP packets received from
+            interfaces, including those received in error."
+              ::= { snArpStats 1 }
+
+snArpStatsRequestReceived OBJECT-TYPE
+    SYNTAX         Counter32
+    MAX-ACCESS  read-only
+    STATUS         current
+    DESCRIPTION
+            "The total number of input ARP Request packets received from
+            interfaces."
+              ::= { snArpStats 2 }
+
+snArpStatsRequestSent OBJECT-TYPE
+    SYNTAX         Counter32
+    MAX-ACCESS  read-only
+    STATUS         current
+    DESCRIPTION
+            "The total number of output ARP Request packets sent from
+            interfaces."
+              ::= { snArpStats 3 }
+
+snArpStatsRepliesSent OBJECT-TYPE
+    SYNTAX         Counter32
+    MAX-ACCESS  read-only
+    STATUS         current
+    DESCRIPTION
+            "The total number of output ARP Reply packets sent from
+            interfaces."
+              ::= { snArpStats 4 }
+
+snArpStatsPendingDrop OBJECT-TYPE
+    SYNTAX         Counter32
+    MAX-ACCESS  read-only
+    STATUS         current
+    DESCRIPTION
+            "The total number of ARP pending packets discarded."
+              ::= { snArpStats 5 }
+
+snArpStatsInvalidSource OBJECT-TYPE
+    SYNTAX         Counter32
+    MAX-ACCESS  read-only
+    STATUS         current
+    DESCRIPTION
+            "The total number of ARP packets received with invalid
+            sender protocol address."
+              ::= { snArpStats 6 }
+
+snArpStatsInvalidDestination OBJECT-TYPE
+    SYNTAX         Counter32
+    MAX-ACCESS  read-only
+    STATUS         current
+    DESCRIPTION
+            "The total number of ARP packets received with invalid
+            destination protocol address."
+              ::= { snArpStats 7 }
+
+
+END

mibs/FOUNDRY-SN-CAM-MIB

@@ -0,0 +1,511 @@
+FOUNDRY-SN-CAM-MIB DEFINITIONS ::= BEGIN
+IMPORTS
+    MODULE-IDENTITY,
+    OBJECT-TYPE,
+    Gauge32,
+    Unsigned32
+        FROM SNMPv2-SMI               -- [RFC2578]
+    TEXTUAL-CONVENTION
+        FROM SNMPv2-TC                 -- [RFC2579]
+    platform
+        FROM FOUNDRY-SN-ROOT-MIB;
+
+snCamMIB MODULE-IDENTITY
+    LAST-UPDATED "201006020000Z"  -- 04 June 2010
+    ORGANIZATION "Brocade Communications Systems, Inc."
+    CONTACT-INFO
+             "Technical Support Center
+              130 Holger Way,
+              San Jose, CA  95134
+              Email:  ipsupport@brocade.com
+              Phone: 1-800-752-8061
+              URL:  www.brocade.com"
+    DESCRIPTION
+             "The MIB module to describe generic objects for the usage of
+              Content Addressable Memory (CAM).
+
+              Copyright 1996-2010 Brocade Communications Systems, Inc.
+              All rights reserved.
+              This Brocade Communications Systems SNMP Management Information Base Specification
+              embodies Brocade Communications Systems' confidential and proprietary
+              intellectual property. Brocade Communications Systems retains all
+              title and ownership in the Specification, including any revisions.
+
+              This Specification is supplied AS IS, and Brocade Communications Systems makes
+              no warranty, either express or implied, as to the use,
+              operation, condition, or performance of the specification, and any unintended
+              consequence it may on the user environment."
+
+    REVISION        "201006020000Z"  -- 04 June 2010
+    DESCRIPTION
+        "Changed the ORGANIZATION, CONTACT-INFO and DESCRIPTION fields."
+
+    REVISION      "200711190000Z"		-- Nov 19, 2007
+    DESCRIPTION
+            "Initial revision"
+    ::= { platform 1  }
+
+
+--
+-- Textual Conventions
+--
+
+-- Percentage
+--
+Percent ::= TEXTUAL-CONVENTION
+    STATUS current
+    DESCRIPTION
+        "An integer that is in the range of a percent value."
+    SYNTAX Gauge32 (0..100)
+
+--
+-- high level object identifiers
+--
+snCamObjects  OBJECT IDENTIFIER ::= { snCamMIB 1 }
+
+
+-- snCamProfile
+snCamProfile OBJECT-TYPE
+    SYNTAX  INTEGER {
+                default(1),
+                ipv4(2),
+                ipv4Ipv6(3),
+                ipv4Ipv62(4),
+                ipv4Vpls(5),
+                ipv4Vpn(6),
+                ipv6(7),
+                l2Metro(8),
+                l2Metro2(9),
+                mplsL3vpn(10),
+                mplsL3vpn2(11),
+                mplsVpls(12),
+                mplsVpls2(13),
+                mplsVpnVpls(14),
+                multiService(15),
+                multiService2(16),
+                multiService3(17),
+                multiService4(18)
+            }
+    MAX-ACCESS  read-only
+    STATUS      current
+    DESCRIPTION
+            "This object identifies CAM partition profile. Each profile
+            adjusts the partitions to optimize the device for corresponding
+            applications."
+    ::= { snCamObjects 1 }
+
+
+-- cam usage objects
+snCamUsage  OBJECT IDENTIFIER ::= { snCamObjects 2 }
+
+
+-- the snCamUsageL3 table
+
+-- The snCamUsageL3 table contains information of the entity's
+-- CAM usage for layer 3 traffic.
+
+snCamUsageL3Table OBJECT-TYPE
+    SYNTAX      SEQUENCE OF SnCamUsageL3Entry
+    MAX-ACCESS  not-accessible
+    STATUS      current
+    DESCRIPTION
+            "A list of snCamUsageL3 entries. This table contains
+            information of the entity's CAM usage for layer 3 traffic."
+    ::= { snCamUsage 1 }
+
+snCamUsageL3Entry OBJECT-TYPE
+    SYNTAX      SnCamUsageL3Entry
+    MAX-ACCESS  not-accessible
+    STATUS      current
+    DESCRIPTION
+            "An entry containing management information applicable to
+            CAM usage for layer 3 traffic"
+    INDEX   {   snCamUsageL3Slot,
+                    snCamUsageL3Processor,
+                    snCamUsageL3Type,
+                    snCamUsageL3Supernet   }
+    ::= { snCamUsageL3Table 1 }
+
+SnCamUsageL3Entry ::=
+    SEQUENCE {
+        snCamUsageL3Slot			Unsigned32,
+        snCamUsageL3Processor		Unsigned32,
+        snCamUsageL3Type			INTEGER,
+        snCamUsageL3Supernet		Unsigned32,
+        snCamUsageL3Size			Unsigned32,
+        snCamUsageL3Free			Gauge32,
+        snCamUsageL3UsedPercent		Percent
+    }
+
+snCamUsageL3Slot OBJECT-TYPE
+    SYNTAX  Unsigned32
+    MAX-ACCESS  not-accessible
+    STATUS      current
+    DESCRIPTION
+            "A number which uniquely identifies a linecard  in the device"
+    ::= { snCamUsageL3Entry 1 }
+
+snCamUsageL3Processor OBJECT-TYPE
+    SYNTAX  Unsigned32 (1..2)
+    MAX-ACCESS  not-accessible
+    STATUS      current
+    DESCRIPTION
+            "A number which uniquely identifies the network processor within a
+            linecard in the device"
+    ::= { snCamUsageL3Entry 2 }
+
+snCamUsageL3Type OBJECT-TYPE
+    SYNTAX  INTEGER {
+                ipv4(1),
+                ipv6(2),
+                ipv4vpn(3),
+                ipv6vpn(4)
+            }
+    MAX-ACCESS  not-accessible
+    STATUS      current
+    DESCRIPTION
+            "This object identifies the type of layer 3 traffic passing through the
+            network processor."
+    ::= { snCamUsageL3Entry 3 }
+
+snCamUsageL3Supernet OBJECT-TYPE
+    SYNTAX  Unsigned32
+    MAX-ACCESS  not-accessible
+    STATUS      current
+    DESCRIPTION
+            "This object identifies the Supernet for the layer 3 type traffic. It
+            provides information for longest match lookup. For example,  zero
+            indicates all the bits of IP address will be matched, and one indicates
+            all but the lowest bit in IP address will be matched. The range is
+            [0..32] for IPv4 and IPv4VPN, where a value of 32 indicates the entry is
+            the total of other supernets indexed by [0..31]. The range is [0..10] for
+            IPv6, where a value of 10 indicates the entry is the total of other
+            supernets indexed by [0..9]."
+    ::= { snCamUsageL3Entry 4 }
+
+snCamUsageL3Size OBJECT-TYPE
+    SYNTAX  Unsigned32
+    UNITS   "Entries"
+    MAX-ACCESS  read-only
+    STATUS      current
+    DESCRIPTION
+            "The effective CAM size for this layer 3 traffic entry. For ipv4 traffic, each
+            unit is 4 bytes. For ipv4vpn, each unit is 8 bytes. For ipv6, each unit is
+            16 bytes."
+    ::= { snCamUsageL3Entry 5 }
+
+snCamUsageL3Free OBJECT-TYPE
+    SYNTAX  Gauge32
+    UNITS   "Entries"
+    MAX-ACCESS  read-only
+    STATUS      current
+    DESCRIPTION
+            "The amount of CAM currently available for this layer 3 traffic entry. For ipv4
+            traffic, each unit is 4 bytes. For ipv4vpn, each unit is 8 bytes. For ipv6, each
+            unit is 16 bytes."
+    ::= { snCamUsageL3Entry 6 }
+
+snCamUsageL3UsedPercent OBJECT-TYPE
+    SYNTAX  Percent
+    MAX-ACCESS  read-only
+    STATUS      current
+    DESCRIPTION
+            "The percentage of CAM currently being used for this layer 3 traffic entry. "
+    ::= { snCamUsageL3Entry 7 }
+
+
+-- the snCamUsageL2 table
+
+-- The snCamUsageL2 table contains information of the entity's
+-- CAM usage for layer 2 traffic.
+
+snCamUsageL2Table OBJECT-TYPE
+    SYNTAX      SEQUENCE OF SnCamUsageL2Entry
+    MAX-ACCESS  not-accessible
+    STATUS      current
+    DESCRIPTION
+            "A list of snCamUsageL2 entries. This table contains information of
+            the entity's CAM usage for layer 2 traffic."
+    ::= { snCamUsage 2 }
+
+snCamUsageL2Entry OBJECT-TYPE
+    SYNTAX      SnCamUsageL2Entry
+    MAX-ACCESS  not-accessible
+    STATUS      current
+    DESCRIPTION
+            "An entry containing management information applicable to
+            CAM usage for layer 2 traffic"
+    INDEX   {	snCamUsageL2Slot,
+			snCamUsageL2Processor,
+			snCamUsageL2Type }
+    ::= { snCamUsageL2Table 1 }
+
+SnCamUsageL2Entry ::=
+    SEQUENCE {
+        snCamUsageL2Slot			Unsigned32,
+        snCamUsageL2Processor		Unsigned32,
+        snCamUsageL2Type			INTEGER,
+        snCamUsageL2Size			Unsigned32,
+        snCamUsageL2Free			Gauge32,
+        snCamUsageL2UsedPercent		Percent
+    }
+
+snCamUsageL2Slot OBJECT-TYPE
+    SYNTAX  Unsigned32
+    MAX-ACCESS  not-accessible
+    STATUS      current
+    DESCRIPTION
+            "A number which uniquely identifies a linecard in the device"
+    ::= { snCamUsageL2Entry 1 }
+
+snCamUsageL2Processor OBJECT-TYPE
+    SYNTAX  Unsigned32 (1..2)
+    MAX-ACCESS  not-accessible
+    STATUS      current
+    DESCRIPTION
+            "A number which uniquely identifies the network processor within a
+            linecard in the device"
+    ::= { snCamUsageL2Entry 2 }
+
+snCamUsageL2Type OBJECT-TYPE
+    SYNTAX  INTEGER {
+                forwarding(1),
+                protocol(2),
+                flooding(3),
+                total(4)
+            }
+    MAX-ACCESS  not-accessible
+    STATUS      current
+    DESCRIPTION
+            "This object identifies the type of layer 2 traffic passing through
+            the network processor."
+    ::= { snCamUsageL2Entry 3 }
+
+snCamUsageL2Size OBJECT-TYPE
+    SYNTAX  Unsigned32
+    UNITS  "Entries"
+    MAX-ACCESS  read-only
+    STATUS      current
+    DESCRIPTION
+            "The effective CAM size for this layer 2 traffic entry. Each unit is 8 bytes."
+    ::= { snCamUsageL2Entry 4 }
+
+snCamUsageL2Free OBJECT-TYPE
+    SYNTAX  Gauge32
+    UNITS  "Entries"
+    MAX-ACCESS  read-only
+    STATUS      current
+    DESCRIPTION
+            "The amount of CAM currently available for this layer 2 traffic entry.
+             Each unit is 8 bytes."
+    ::= { snCamUsageL2Entry 5 }
+
+snCamUsageL2UsedPercent OBJECT-TYPE
+    SYNTAX  Percent
+    MAX-ACCESS  read-only
+    STATUS      current
+    DESCRIPTION
+            "The percentage of CAM currently being used for this layer 2 traffic entry. "
+    ::= { snCamUsageL2Entry 6 }
+
+-- the snCamUsageSession table
+
+-- The snCamUsageSession table contains information of the entity's
+-- CAM usage for sessions.
+
+snCamUsageSessionTable OBJECT-TYPE
+    SYNTAX      SEQUENCE OF SnCamUsageSessionEntry
+    MAX-ACCESS  not-accessible
+    STATUS      current
+    DESCRIPTION
+            "A list of snCamUsageSession entries. This table contains information
+            of the entitiy's CAM usage for sessions. "
+    ::= { snCamUsage 3 }
+
+snCamUsageSessionEntry OBJECT-TYPE
+    SYNTAX      SnCamUsageSessionEntry
+    MAX-ACCESS  not-accessible
+    STATUS      current
+    DESCRIPTION
+            "An entry containing management information applicable to CAM usage
+            for sessions. "
+    INDEX   { snCamUsageSessionSlot,
+                   snCamUsageSessionProcessor,
+                   snCamUsageSessionType }
+    ::= { snCamUsageSessionTable 1 }
+
+SnCamUsageSessionEntry ::=
+    SEQUENCE {
+        snCamUsageSessionSlot			Unsigned32,
+        snCamUsageSessionProcessor		Unsigned32,
+        snCamUsageSessionType			INTEGER,
+        snCamUsageSessionSize			Unsigned32,
+        snCamUsageSessionFree			Gauge32,
+        snCamUsageSessionUsedPercent		Percent
+    }
+
+snCamUsageSessionSlot OBJECT-TYPE
+    SYNTAX  Unsigned32
+    MAX-ACCESS  not-accessible
+    STATUS      current
+    DESCRIPTION
+            "A number which uniquely identifies a linecard in the device"
+    ::= { snCamUsageSessionEntry 1 }
+
+snCamUsageSessionProcessor OBJECT-TYPE
+    SYNTAX  Unsigned32 (1..2)
+    MAX-ACCESS  not-accessible
+    STATUS      current
+    DESCRIPTION
+            "A number which uniquely identifies the network processor within a
+            linecard in the device"
+    ::= { snCamUsageSessionEntry 2 }
+
+snCamUsageSessionType OBJECT-TYPE
+    SYNTAX  INTEGER {
+                ipv4Multicast(1),
+                ipv4andMacReceiveAcl(2),
+                ipv4andMacRuleAcl(3),
+                ipv4andMacTotal(4),
+                ipv4andMacOut(5),
+                ipv6Multicast(6),
+                ipv6ReceiveAcl(7),
+                ipv6RuleAcl(8),
+                ipv6Total(9),
+                ipv6Out(10),
+                labelOut(11),
+                ipv4SrcGuardDenial(12),
+                ipv4SrcGuardPermit(13),
+                internalForwardingLookup(14)
+            }
+    MAX-ACCESS  not-accessible
+    STATUS      current
+    DESCRIPTION
+            "This object identifies the type of sessions."
+    ::= { snCamUsageSessionEntry 3 }
+
+
+snCamUsageSessionSize OBJECT-TYPE
+    SYNTAX  Unsigned32
+    UNITS  "Entries"
+    MAX-ACCESS  read-only
+    STATUS      current
+    DESCRIPTION
+            "The effective CAM size for this session traffic entry. For IPv4 sessions,
+            each unit is 16 bytes. For IPv4 sessions, each unit is 64 bytes."
+    ::= { snCamUsageSessionEntry 4 }
+
+snCamUsageSessionFree OBJECT-TYPE
+    SYNTAX  Gauge32
+    UNITS  "Entries"
+    MAX-ACCESS  read-only
+    STATUS      current
+    DESCRIPTION
+        "The amount of CAM currently available this session traffic entry.
+        For IPv4 sessions, each unit is 16 bytes. For IPv4 sessions, each unit is
+        64 bytes."
+    ::= { snCamUsageSessionEntry 5 }
+
+snCamUsageSessionUsedPercent OBJECT-TYPE
+    SYNTAX  Percent
+    MAX-ACCESS  read-only
+    STATUS      current
+    DESCRIPTION
+            "The percentage of CAM currently being used by this session traffic entry "
+    ::= { snCamUsageSessionEntry 6 }
+
+
+-- the snCamUsageOther table
+
+-- The snCamUsageOthers table contains information of the entity's
+-- CAM usage for types other than L3, L2, or Session.
+
+snCamUsageOtherTable OBJECT-TYPE
+    SYNTAX      SEQUENCE OF SnCamUsageOtherEntry
+    MAX-ACCESS  not-accessible
+    STATUS      current
+    DESCRIPTION
+            "A list of snCamUsageOther entries. This table contains information
+            of the entitiy's CAM usage for types other than L3, L2, or Session."
+    ::= { snCamUsage 4 }
+
+snCamUsageOtherEntry OBJECT-TYPE
+    SYNTAX      SnCamUsageOtherEntry
+    MAX-ACCESS  not-accessible
+    STATUS      current
+    DESCRIPTION
+            "An entry containing management information applicable to CAM usage
+            for types other than L3, L2, or Session"
+    INDEX   { snCamUsageOtherSlot,
+              snCamUsageOtherProcessor,
+              snCamUsageOtherType }
+    ::= { snCamUsageOtherTable 1 }
+
+SnCamUsageOtherEntry ::=
+    SEQUENCE {
+        snCamUsageOtherSlot			Unsigned32,
+        snCamUsageOtherProcessor		Unsigned32,
+        snCamUsageOtherType			INTEGER,
+        snCamUsageOtherSize			Unsigned32,
+        snCamUsageOtherFree			Gauge32,
+        snCamUsageOtherUsedPercent		Percent
+    }
+
+snCamUsageOtherSlot OBJECT-TYPE
+    SYNTAX  Unsigned32
+    MAX-ACCESS  not-accessible
+    STATUS      current
+    DESCRIPTION
+            "A number which uniquely identifies a linecard in the device"
+    ::= { snCamUsageOtherEntry 1 }
+
+snCamUsageOtherProcessor OBJECT-TYPE
+    SYNTAX  Unsigned32 (1..2)
+    MAX-ACCESS  not-accessible
+    STATUS      current
+    DESCRIPTION
+            "A number which uniquely identifies the network processor within a
+            linecard in the device"
+    ::= { snCamUsageOtherEntry 2 }
+
+snCamUsageOtherType OBJECT-TYPE
+    SYNTAX  INTEGER {
+                gre(1),
+                multicastVpls(2)
+            }
+    MAX-ACCESS  not-accessible
+    STATUS      current
+    DESCRIPTION
+            "This object identifies the type."
+    ::= { snCamUsageOtherEntry 3 }
+
+snCamUsageOtherSize OBJECT-TYPE
+    SYNTAX  Unsigned32
+    UNITS  "Entries"
+    MAX-ACCESS  read-only
+    STATUS      current
+    DESCRIPTION
+            "The effective CAM size for this Other traffic entry. For GRE,
+            each unit is 8 bytes. For multicast VPLS, each unit is 16 bytes."
+    ::= { snCamUsageOtherEntry 4 }
+
+snCamUsageOtherFree OBJECT-TYPE
+    SYNTAX  Gauge32
+    UNITS  "Entries"
+    MAX-ACCESS  read-only
+    STATUS      current
+    DESCRIPTION
+            "The amount of CAM currently available this Other traffic entry.
+            For GRE, each unit is 8 bytes. For multicast VPLS, each unit is 16 bytes."
+    ::= { snCamUsageOtherEntry 5 }
+
+snCamUsageOtherUsedPercent OBJECT-TYPE
+    SYNTAX  Percent
+    MAX-ACCESS  read-only
+    STATUS      current
+    DESCRIPTION
+            "The percentage of CAM currently being used by this entry "
+    ::= { snCamUsageOtherEntry 6 }
+
+
+END

mibs/FOUNDRY-SN-IGMP-MIB

@@ -1,129 +1,207 @@
-FOUNDRY-SN-IGMP-MIB DEFINITIONS ::= BEGIN
-
-
--- Foundry IGMP Group MIB Release 1.0.0
--- Revision 0 2/13/98
-
--- Copyright 1996-98 Foundry Networks, Inc.
--- All rights reserved.
--- This Foundry Networks SNMP Management Information Base 
--- Specification embodies Foundry Networks' confidential and
--- proprietary intellectual property. Foundry Networks retains all
--- title and ownership in the Specification, including any
--- revisions.
-
--- This Specification is supplied "AS IS," and Foundry Networks makes
--- no warranty, either express or implied, as to the use,
--- operation, condition, or performance of the Specification.
-
--- SECTION 1: Top Level Definitions
-
-
--- Imports
-
-IMPORTS
-	IpAddress
-		FROM RFC1155-SMI
-	OBJECT-TYPE
-		FROM RFC-1212
-	snIgmp
-		FROM FOUNDRY-SN-ROOT-MIB;
-
-
--- SECTION 2: MIB 
-
--- IGMP MIB
-
-snIgmpMIBObjects OBJECT IDENTIFIER ::= { snIgmp 1 }
-
-snIgmpQueryInterval OBJECT-TYPE
-    SYNTAX     INTEGER (0..3600)
-    ACCESS     read-write
-    STATUS     mandatory
-    DESCRIPTION
-            "This is the time interval at which this entity sends out
-			IGMP host query packets. For a router, snDvmrpEnable must
-			have been set to 'enabled' before this object is writen.
-			For a switch, snSwGroupIpMcastMode must have been set to
-			'enabled' and snSwIpMcastQuerierMode must have been set
-			to 'querier' before this object is writen.
-			Value 0 cannot be used for SET operations. This value
-			is returned if IGMP is not configured within the system."
-    DEFVAL     { 60 }
-    ::= { snIgmpMIBObjects 1 }
-
-snIgmpGroupMembershipTime OBJECT-TYPE
-    SYNTAX     INTEGER (0..7200)
-    ACCESS     read-write
-    STATUS     mandatory
-    DESCRIPTION
-            "This is the time interval after which a group is considered
-            inactive. For a router, snDvmrpEnable must have been set to
-            'enabled' before this object is writen. For a switch,
-            snSwGroupIpMcastMode must have been set to 'enabled' before
-            this object is writen.
-            Value 0 cannot be used for SET operations. This value
-            is returned if IGMP is not configured within the system."
-    DEFVAL     { 140 }
-    ::= { snIgmpMIBObjects 2 }
-
--- The IGMP Interface Table
-
-snIgmpIfTable OBJECT-TYPE
-    SYNTAX     SEQUENCE OF SnIgmpIfEntry
-    ACCESS     not-accessible
-    STATUS     mandatory
-    DESCRIPTION
-            "This table comprises of a list of IGMP interface entries."
-    ::= { snIgmpMIBObjects 3 }
-
-snIgmpIfEntry OBJECT-TYPE
-    SYNTAX     SnIgmpIfEntry
-    ACCESS     not-accessible
-    STATUS     mandatory
-    DESCRIPTION
-            "An entry (conceptual row) contains the group
-            membership information for that port."
-    INDEX      { snIgmpIfEntryIndex }
-    ::= { snIgmpIfTable 1 }
-
-SnIgmpIfEntry ::= SEQUENCE {
-    snIgmpIfEntryIndex         INTEGER,
-    snIgmpIfPortNumber         INTEGER,
-    snIgmpIfGroupAddress       IpAddress,
-    snIgmpIfGroupAge           INTEGER }
-
-snIgmpIfEntryIndex OBJECT-TYPE
-    SYNTAX     INTEGER
-    ACCESS     read-only
-    STATUS     mandatory
-    DESCRIPTION
-            "The table entry index."
-    ::= { snIgmpIfEntry 1 }
-
-snIgmpIfPortNumber OBJECT-TYPE
-    SYNTAX     INTEGER
-    ACCESS     read-only
-    STATUS     mandatory
-    DESCRIPTION
-            "This is the interface on which the group was learnt."
-    ::= { snIgmpIfEntry 2 }
-
-snIgmpIfGroupAddress OBJECT-TYPE
-    SYNTAX     IpAddress
-    ACCESS     read-only
-    STATUS     mandatory
-    DESCRIPTION
-            "The group address learnt from the interface."
-    ::= { snIgmpIfEntry 3 }
-
-snIgmpIfGroupAge OBJECT-TYPE
-    SYNTAX     INTEGER
-    ACCESS     read-only
-    STATUS     mandatory
-    DESCRIPTION
-            "This is the interval (seconds) after which the group
-            information will be aged out."
-    ::= { snIgmpIfEntry 4 }
-
-END
+FOUNDRY-SN-IGMP-MIB DEFINITIONS ::= BEGIN
+
+IMPORTS
+	MODULE-IDENTITY, OBJECT-TYPE,IpAddress,Integer32
+		FROM SNMPv2-SMI
+	router
+		FROM FOUNDRY-SN-ROOT-MIB
+		;
+
+snIgmp MODULE-IDENTITY
+    LAST-UPDATED "201006020000Z"  -- 04 June 2010
+    ORGANIZATION "Brocade Communications Systems, Inc."
+    CONTACT-INFO
+             "Technical Support Center
+              130 Holger Way,
+              San Jose, CA  95134
+              Email:  ipsupport@brocade.com
+              Phone: 1-800-752-8061
+              URL:  www.brocade.com"
+    DESCRIPTION
+             "Copyright 1996-2010 Brocade Communications Systems, Inc.
+              All rights reserved.
+              This Brocade Communications Systems SNMP Management Information Base Specification
+              embodies Brocade Communications Systems' confidential and proprietary
+              intellectual property. Brocade Communications Systems retains all
+              title and ownership in the Specification, including any revisions.
+
+              This Specification is supplied AS IS, and Brocade Communications Systems makes
+              no warranty, either express or implied, as to the use,
+              operation, condition, or performance of the specification, and any unintended
+              consequence it may on the user environment."
+
+    REVISION        "201006020000Z"  -- 04 June 2010
+    DESCRIPTION
+        "Changed the ORGANIZATION, CONTACT-INFO and DESCRIPTION fields."
+
+    REVISION     "200909300000Z" -- September 30, 2009
+    DESCRIPTION
+			""
+   ::= { router 6}
+
+
+-- SECTION 2: MIB
+
+-- IGMP MIB
+
+snIgmpMIBObjects OBJECT IDENTIFIER ::= { snIgmp 1 }
+
+snIgmpQueryInterval OBJECT-TYPE
+	SYNTAX     INTEGER (0..3600)
+	MAX-ACCESS     read-write
+	STATUS     current
+	DESCRIPTION
+			"This is the time interval at which this entity sends out
+			IGMP host query packets. For a router, snDvmrpEnable must
+			have been set to 'enabled' before this object is writen.
+			For a switch, snSwGroupIpMcastMode must have been set to
+			'enabled' and snSwIpMcastQuerierMode must have been set
+			to 'querier' before this object is writen.
+			Value 0 cannot be used for SET operations. This value
+			is returned if IGMP is not configured within the system.
+			For FI platform the configurable range for this object is
+			10 .. 3600"
+	DEFVAL     { 60 }
+	::= { snIgmpMIBObjects 1 }
+
+snIgmpGroupMembershipTime OBJECT-TYPE
+	SYNTAX     INTEGER (0..7200)
+	MAX-ACCESS     read-write
+	STATUS     current
+	DESCRIPTION
+			"This is the time interval after which a group is considered
+			inactive. For a router, snDvmrpEnable must have been set to
+			'enabled' before this object is writen. For a switch,
+			snSwGroupIpMcastMode must have been set to 'enabled' before
+			this object is writen.
+			Value 0 cannot be used for SET operations. This value
+			is returned if IGMP is not configured within the system.
+			For FI platform the configurable range for this object is
+			20 .. 7200"
+	DEFVAL     { 140 }
+	::= { snIgmpMIBObjects 2 }
+
+-- The IGMP Interface Table
+
+snIgmpIfTable OBJECT-TYPE
+	SYNTAX     SEQUENCE OF SnIgmpIfEntry
+	MAX-ACCESS     not-accessible
+	STATUS     current
+	DESCRIPTION
+			"This table comprises of a list of IGMP interface entries."
+	::= { snIgmpMIBObjects 3 }
+
+snIgmpIfEntry OBJECT-TYPE
+	SYNTAX     SnIgmpIfEntry
+	MAX-ACCESS     not-accessible
+	STATUS     current
+	DESCRIPTION
+			"An entry (conceptual row) contains the group
+			membership information for that port."
+	INDEX      { snIgmpIfEntryIndex }
+	::= { snIgmpIfTable 1 }
+
+SnIgmpIfEntry ::= SEQUENCE {
+	snIgmpIfEntryIndex         Integer32,
+	snIgmpIfPortNumber         Integer32,
+	snIgmpIfGroupAddress       IpAddress,
+	snIgmpIfGroupAge           Integer32 }
+
+snIgmpIfEntryIndex OBJECT-TYPE
+	SYNTAX     Integer32
+	MAX-ACCESS     read-only
+	STATUS     current
+	DESCRIPTION
+			"The table entry index."
+	::= { snIgmpIfEntry 1 }
+
+snIgmpIfPortNumber OBJECT-TYPE
+	SYNTAX     Integer32
+	MAX-ACCESS     read-only
+	STATUS     current
+	DESCRIPTION
+			"This is the interface on which the group was learnt."
+	::= { snIgmpIfEntry 2 }
+
+snIgmpIfGroupAddress OBJECT-TYPE
+	SYNTAX     IpAddress
+	MAX-ACCESS     read-only
+	STATUS     current
+	DESCRIPTION
+			"The group address learnt from the interface."
+	::= { snIgmpIfEntry 3 }
+
+snIgmpIfGroupAge OBJECT-TYPE
+	SYNTAX     Integer32
+	MAX-ACCESS     read-only
+	STATUS     current
+	DESCRIPTION
+			"This is the interval (seconds) after which the group
+			information will be aged out."
+	::= { snIgmpIfEntry 4 }
+
+-- The IGMP Static Group Table
+
+snIgmpStaticGroupTable OBJECT-TYPE
+	SYNTAX     SEQUENCE OF SnIgmpStaticGroupEntry
+	MAX-ACCESS     not-accessible
+	STATUS     current
+	DESCRIPTION
+			"This table comprises of a list of IGMP static group entries."
+	::= { snIgmpMIBObjects 4 }
+
+snIgmpStaticGroupEntry OBJECT-TYPE
+	SYNTAX     SnIgmpStaticGroupEntry
+	MAX-ACCESS     not-accessible
+	STATUS     current
+	DESCRIPTION
+			"An entry (conceptual row) contains the IGMP static group
+			membership information."
+	INDEX      { snIgmpStaticGroupIfIndex, snIgmpStaticGroupAddress }
+	::= { snIgmpStaticGroupTable 1 }
+
+SnIgmpStaticGroupEntry ::= SEQUENCE {
+	snIgmpStaticGroupIfIndex    Integer32,
+	snIgmpStaticGroupAddress    IpAddress,
+	snIgmpStaticGroupPortList   OCTET STRING,
+	snIgmpStaticGroupRowStatus  INTEGER }
+
+snIgmpStaticGroupIfIndex OBJECT-TYPE
+	SYNTAX     Integer32
+	MAX-ACCESS     read-only
+	STATUS     current
+	DESCRIPTION
+			"The interface of which the static group was configured."
+	::= { snIgmpStaticGroupEntry 1 }
+
+snIgmpStaticGroupAddress OBJECT-TYPE
+	SYNTAX     IpAddress
+	MAX-ACCESS     read-only
+	STATUS     current
+	DESCRIPTION
+			"The group address of which the static group was configured."
+	::= { snIgmpStaticGroupEntry 2 }
+
+snIgmpStaticGroupPortList OBJECT-TYPE
+	SYNTAX     OCTET STRING
+	MAX-ACCESS     read-write
+	STATUS     current
+	DESCRIPTION
+			"A list of ports which are the port membership of the
+			static group. Each port is a 16-bit integer ifIndex."
+	::= { snIgmpStaticGroupEntry 3 }
+
+snIgmpStaticGroupRowStatus OBJECT-TYPE
+	SYNTAX     INTEGER {
+				 other(1),
+				 valid(2),
+				 delete(3),
+				 create(4),
+				 modify(5) }
+	MAX-ACCESS     read-write
+	STATUS     current
+	DESCRIPTION
+			"To create or delete a static group entry."
+	::= { snIgmpStaticGroupEntry 4 }
+
+END

mibs/FOUNDRY-SN-MAC-AUTHENTICATION-MIB

@@ -0,0 +1,257 @@
+FOUNDRY-SN-MAC-AUTHENTICATION-MIB DEFINITIONS ::= BEGIN
+
+IMPORTS
+    MODULE-IDENTITY, OBJECT-TYPE, Integer32
+      FROM SNMPv2-SMI
+    MacAddress, TimeStamp
+      FROM SNMPv2-TC
+    InterfaceIndex
+      FROM IF-MIB;
+
+
+snMacAuth MODULE-IDENTITY
+    LAST-UPDATED "201006020000Z"  -- 04 June 2010
+    ORGANIZATION "Brocade Communications Systems, Inc."
+    CONTACT-INFO
+             "Technical Support Center
+              130 Holger Way,
+              San Jose, CA  95134
+              Email:  ipsupport@brocade.com
+              Phone: 1-800-752-8061
+              URL:  www.brocade.com"
+    DESCRIPTION
+             "Management Information Base module for MAC authentication
+              configuration and statistics.
+
+              Copyright 1996-2010 Brocade Communications Systems, Inc.
+              All rights reserved.
+              This Brocade Communications Systems SNMP Management Information Base Specification
+              embodies Brocade Communications Systems' confidential and proprietary
+              intellectual property. Brocade Communications Systems retains all
+              title and ownership in the Specification, including any revisions.
+
+              This Specification is supplied AS IS, and Brocade Communications Systems makes
+              no warranty, either express or implied, as to the use,
+              operation, condition, or performance of the specification, and any unintended
+              consequence it may on the user environment."
+
+    REVISION        "201006020000Z"  -- 04 June 2010
+    DESCRIPTION
+        "Changed the ORGANIZATION, CONTACT-INFO and DESCRIPTION fields."
+
+    REVISION     "200706250000Z" -- June 25, 2007
+    DESCRIPTION
+            ""
+   ::= { iso(1) org(3) dod(6) internet(1) private(4) enterprises(1) foundry(1991) products(1) switch(1) snSwitch(3) 28 }
+
+
+-- MAC Authentication MIBs
+
+snMacAuthGlobal		OBJECT IDENTIFIER ::= { snMacAuth 1 }
+
+snMacAuthClearGlobalCmd OBJECT-TYPE
+	SYNTAX     INTEGER { valid(0), clear(1) }
+	MAX-ACCESS read-write
+	STATUS     current
+	DESCRIPTION
+		"valid(0) - a SNMP-GET of this mib shows that it is valid command to use.
+		 clear(1) - represents clear MAC Authentication table for all ports."
+	::= { snMacAuthGlobal 1 }
+
+snMacAuthGlobalConfigState OBJECT-TYPE
+	SYNTAX     INTEGER { disabled(0), enabled(1) }
+	MAX-ACCESS read-write
+	STATUS     current
+	DESCRIPTION
+		"Enable/disable MAC authentication on the global level."
+	::= { snMacAuthGlobal 2 }
+
+--
+-- MAC Authentication Clear Interface command Table
+--
+
+snMacAuthClearIfCmdTable OBJECT-TYPE
+	SYNTAX     SEQUENCE OF SnMacAuthClearIfCmdEntry
+	MAX-ACCESS not-accessible
+	STATUS     current
+	DESCRIPTION
+		"The status of clearing an MAC Authentication entry for an interface."
+	::= { snMacAuth 2 }
+
+snMacAuthClearIfCmdEntry OBJECT-TYPE
+	SYNTAX     SnMacAuthClearIfCmdEntry
+	MAX-ACCESS not-accessible
+	STATUS     current
+	DESCRIPTION
+		"An entry of clearing an MAC Authentication entry for an interface."
+	INDEX { snMacAuthClearIfCmdIfIndex }
+	::= { snMacAuthClearIfCmdTable 1 }
+
+SnMacAuthClearIfCmdEntry ::= SEQUENCE {
+    snMacAuthClearIfCmdIfIndex     InterfaceIndex,
+    snMacAuthClearIfCmdAction      INTEGER
+}
+
+snMacAuthClearIfCmdIfIndex OBJECT-TYPE
+    SYNTAX     InterfaceIndex
+    MAX-ACCESS not-accessible
+    STATUS     current
+    DESCRIPTION
+            "ifIndex value of the local interface on which a clear command is issued and monitored."
+	::= { snMacAuthClearIfCmdEntry 1 }
+
+snMacAuthClearIfCmdAction      OBJECT-TYPE
+	SYNTAX     INTEGER { valid(0), clear(1) }
+	MAX-ACCESS read-write
+	STATUS     current
+	DESCRIPTION
+		"valid(0) - a SNMP-GET of this mib shows that it is valid command to use.
+		 clear(1) - represents clearing an MAC Authentication entry for an interface."
+	::= { snMacAuthClearIfCmdEntry 2 }
+
+--
+-- MAC Authentication Table
+--
+
+snMacAuthTable OBJECT-TYPE
+	SYNTAX     SEQUENCE OF SnMacAuthEntry
+	MAX-ACCESS not-accessible
+	STATUS     current
+	DESCRIPTION
+		"MAC Authentication table."
+	::= { snMacAuth 3 }
+
+snMacAuthEntry OBJECT-TYPE
+	SYNTAX     SnMacAuthEntry
+	MAX-ACCESS not-accessible
+	STATUS     current
+	DESCRIPTION
+		"An entry in the MAC Authentication table."
+	INDEX { snMacAuthIfIndex, snMacAuthVlanId, snMacAuthMac }
+	::= { snMacAuthTable 1 }
+
+SnMacAuthEntry ::= SEQUENCE {
+    snMacAuthIfIndex               InterfaceIndex,
+    snMacAuthVlanId                Integer32,
+    snMacAuthMac                   MacAddress,
+    snMacAuthState                 INTEGER,
+    snMacAuthTimeStamp             TimeStamp,
+    snMacAuthAge                   Integer32,
+    snMacAuthDot1x                 INTEGER
+}
+
+snMacAuthIfIndex OBJECT-TYPE
+    SYNTAX     InterfaceIndex
+    MAX-ACCESS not-accessible
+    STATUS     current
+    DESCRIPTION
+    	"In order to identify a particular interface, this
+		object shall identify the instance of the ifIndex
+		object, defined in RFC 2863."
+	::= { snMacAuthEntry 1 }
+
+snMacAuthVlanId OBJECT-TYPE
+     SYNTAX     Integer32
+     MAX-ACCESS not-accessible
+     STATUS     current
+     DESCRIPTION
+        "The ID of a VLAN of which this port is a member. Port must
+        be untagged. For tagged port which belongs to multiple
+        VLANs, this object return 0 which is an invalid VLAN ID
+        value."
+     ::= { snMacAuthEntry 2 }
+
+snMacAuthMac OBJECT-TYPE
+	SYNTAX     MacAddress
+	MAX-ACCESS not-accessible
+	STATUS     current
+	DESCRIPTION
+		"MAC Address to be authenticated."
+	::= { snMacAuthEntry 3 }
+
+snMacAuthState OBJECT-TYPE
+	SYNTAX     INTEGER { authenticate(1), unauthenticate(2) }
+	MAX-ACCESS read-only
+	STATUS     current
+	DESCRIPTION
+		"."
+	::= { snMacAuthEntry 4 }
+
+snMacAuthTimeStamp OBJECT-TYPE
+	SYNTAX     TimeStamp
+	MAX-ACCESS read-only
+	STATUS     current
+	DESCRIPTION
+		"Timestamp at which the MAC was authenticated or failed to be authenticated."
+	::= { snMacAuthEntry 5 }
+
+snMacAuthAge OBJECT-TYPE
+	SYNTAX     Integer32
+	MAX-ACCESS read-only
+	STATUS     current
+	DESCRIPTION
+		"Age of the mac session in which the MAC address is authenticated."
+	::= { snMacAuthEntry 6 }
+
+snMacAuthDot1x OBJECT-TYPE
+	SYNTAX     INTEGER { disabled(0), enabled(1) }
+	MAX-ACCESS read-only
+	STATUS     current
+	DESCRIPTION
+		"Indicates whether the Dot1x is enabled or not."
+	::= { snMacAuthEntry 7 }
+
+--
+-- MAC Authentication MAC Session Clear Table
+--
+
+snMacAuthClearMacSessionTable OBJECT-TYPE
+	SYNTAX     SEQUENCE OF SnMacAuthClearMacSessionEntry
+	MAX-ACCESS not-accessible
+	STATUS     current
+	DESCRIPTION
+		"The status of clearing an MAC Session entry indexed by a MAC address."
+	::= { snMacAuth 4 }
+
+snMacAuthClearMacSessionEntry OBJECT-TYPE
+	SYNTAX     SnMacAuthClearMacSessionEntry
+	MAX-ACCESS not-accessible
+	STATUS     current
+	DESCRIPTION
+		"An entry of clearing an MAC Session entry indexed by a MAC address."
+	INDEX { snMacAuthClearMacSessionIfIndex, snMacAuthClearMacSessionMac }
+	::= { snMacAuthClearMacSessionTable 1 }
+
+SnMacAuthClearMacSessionEntry ::= SEQUENCE {
+    snMacAuthClearMacSessionIfIndex InterfaceIndex,
+    snMacAuthClearMacSessionMac     MacAddress,
+    snMacAuthClearMacSessionAction  INTEGER
+}
+
+snMacAuthClearMacSessionIfIndex OBJECT-TYPE
+    SYNTAX     InterfaceIndex
+    MAX-ACCESS not-accessible
+    STATUS     current
+    DESCRIPTION
+            "ifIndex value of the local interface on which a clear command is issued and monitored."
+	::= { snMacAuthClearMacSessionEntry 1 }
+
+snMacAuthClearMacSessionMac OBJECT-TYPE
+	SYNTAX     MacAddress
+	MAX-ACCESS not-accessible
+	STATUS     current
+	DESCRIPTION
+		"An MAC Session entry indexed by a MAC address."
+	::= { snMacAuthClearMacSessionEntry 2 }
+
+snMacAuthClearMacSessionAction OBJECT-TYPE
+	SYNTAX     INTEGER { valid(0), clear(1) }
+	MAX-ACCESS read-write
+	STATUS     current
+	DESCRIPTION
+		"valid(0) - a SNMP-GET of this mib shows that it is valid command to use.
+		 clear(1) - represents clearing an MAC Session entry indexed by a MAC address."
+	::= { snMacAuthClearMacSessionEntry 3 }
+
+END
+

mibs/FOUNDRY-SN-MRP-MIB

@@ -0,0 +1,347 @@
+FOUNDRY-SN-MRP-MIB DEFINITIONS ::= BEGIN
+
+IMPORTS
+    MODULE-IDENTITY, OBJECT-TYPE, Integer32, Counter32
+      FROM SNMPv2-SMI
+    InterfaceIndex
+      FROM IF-MIB
+    DisplayString
+      FROM SNMPv2-TC;
+
+snMetroRing MODULE-IDENTITY
+    LAST-UPDATED "201006020000Z"  -- 04 June 2010
+    ORGANIZATION "Brocade Communications Systems, Inc."
+    CONTACT-INFO
+             "Technical Support Center
+              130 Holger Way,
+              San Jose, CA  95134
+              Email:  ipsupport@brocade.com
+              Phone: 1-800-752-8061
+              URL:  www.brocade.com"
+    DESCRIPTION
+             "Management Information Base module for metro ring
+              configuration and statistics.
+
+              Copyright 1996-2010 Brocade Communications Systems, Inc.
+              All rights reserved.
+              This Brocade Communications Systems SNMP Management Information Base Specification
+              embodies Brocade Communications Systems' confidential and proprietary
+              intellectual property. Brocade Communications Systems retains all
+              title and ownership in the Specification, including any revisions.
+
+              This Specification is supplied AS IS, and Brocade Communications Systems makes
+              no warranty, either express or implied, as to the use,
+              operation, condition, or performance of the specification, and any unintended
+              consequence it may on the user environment."
+
+    REVISION        "201006020000Z"  -- 04 June 2010
+    DESCRIPTION
+        "Changed the ORGANIZATION, CONTACT-INFO and DESCRIPTION fields."
+
+    REVISION     "200705160000Z" -- May 16, 2007
+    DESCRIPTION
+            ""
+   ::= { iso(1) org(3) dod(6) internet(1) private(4) enterprises(1) foundry(1991) products(1) switch(1) snSwitch(3) 29 }
+
+snMetroRingGlobalObjects OBJECT IDENTIFIER ::= { snMetroRing 1 }
+snMetroRingTableObjects  OBJECT IDENTIFIER ::= { snMetroRing 2 }
+
+-- Metro Ring Global Scalar Object Section
+
+-- Metro Ring Table Object Section
+
+--
+-- Metro Ring Table
+--
+
+snMetroRingTable OBJECT-TYPE
+    SYNTAX     SEQUENCE OF SnMetroRingEntry
+    MAX-ACCESS not-accessible
+    STATUS     current
+    DESCRIPTION
+            "Metro ring table."
+    ::= { snMetroRingTableObjects 1 }
+
+snMetroRingEntry OBJECT-TYPE
+    SYNTAX     SnMetroRingEntry
+    MAX-ACCESS not-accessible
+    STATUS     current
+    DESCRIPTION
+            "An entry of the metro ring table."
+    INDEX { snMetroRingVLanId, snMetroRingId }
+    ::= { snMetroRingTable 1 }
+
+SnMetroRingEntry ::= SEQUENCE {
+    snMetroRingVLanId              Integer32,
+    snMetroRingId                  Integer32,
+    snMetroRingConfigState         INTEGER,
+    snMetroRingRole                INTEGER,
+    snMetroRingHelloTime           Integer32,
+    snMetroRingPreforwardingTime   Integer32,
+    snMetroRingPort1               InterfaceIndex,
+    snMetroRingPort2               InterfaceIndex,
+    snMetroRingName                DisplayString,
+    snMetroRingRowStatus           INTEGER,
+    snMetroRingOperState           INTEGER,
+    snMetroRingTopoGroupId         Integer32,
+    snMetroRingRHPTransmitted      Counter32,
+    snMetroRingRHPReceived         Counter32,
+    snMetroRingStateChanged        Counter32,
+    snMetroRingTCRBPDUReceived     Counter32,
+    snMetroRingPriPort             InterfaceIndex,
+    snMetroRingSecPort             InterfaceIndex,
+    snMetroRingPriPortState        INTEGER,
+    snMetroRingSecPortState        INTEGER,
+    snMetroRingPriPortType         INTEGER,
+    snMetroRingSecPortType         INTEGER,
+    snMetroRingPriPortActivePort   InterfaceIndex,
+    snMetroRingSecPortActivePort   InterfaceIndex
+}
+
+snMetroRingVLanId OBJECT-TYPE
+    SYNTAX     Integer32
+    MAX-ACCESS not-accessible
+    STATUS     current
+    DESCRIPTION
+            "Identifier of a VLAN that controls the metro ring."
+    ::= { snMetroRingEntry 1 }
+
+snMetroRingId OBJECT-TYPE
+    SYNTAX     Integer32
+    MAX-ACCESS not-accessible
+    STATUS     current
+    DESCRIPTION
+            "Metro ring identifier."
+    ::= { snMetroRingEntry 2 }
+
+snMetroRingConfigState OBJECT-TYPE
+    SYNTAX     INTEGER { other(1), enabled(2), disabled(3) }
+    MAX-ACCESS read-write
+    STATUS     current
+    DESCRIPTION
+            "Metro ring state."
+    ::= { snMetroRingEntry 3 }
+
+snMetroRingRole OBJECT-TYPE
+    SYNTAX     INTEGER { other(1), master(2), member(3) }
+    MAX-ACCESS read-write
+    STATUS     current
+    DESCRIPTION
+            "Metro ring role.
+            other(1).........none of the cases in below.
+            master(2)........device which originates RHP packets.
+            member(3)........device which forwards RHP packets."
+    ::= { snMetroRingEntry 4 }
+
+snMetroRingHelloTime OBJECT-TYPE
+    SYNTAX     Integer32
+    MAX-ACCESS read-write
+    STATUS     current
+    DESCRIPTION
+            "The time interval to periodically transmit ring health
+            protocol (RHP). Each unit is millisecond."
+    ::= { snMetroRingEntry 5 }
+
+snMetroRingPreforwardingTime OBJECT-TYPE
+    SYNTAX     Integer32
+    MAX-ACCESS read-write
+    STATUS     current
+    DESCRIPTION
+            "The time interval of which a metro ring port is staying
+            in preforwarding state before changing to forwarding state.
+            Each unit is millisecond."
+    ::= { snMetroRingEntry 6 }
+
+snMetroRingPort1 OBJECT-TYPE
+    SYNTAX     InterfaceIndex
+    MAX-ACCESS read-write
+    STATUS     current
+    DESCRIPTION
+            "The ifIndex value of port 1 to configure into the metro ring."
+    ::= { snMetroRingEntry 7 }
+
+snMetroRingPort2 OBJECT-TYPE
+    SYNTAX     InterfaceIndex
+    MAX-ACCESS read-write
+    STATUS     current
+    DESCRIPTION
+            "The ifIndex value of port 2 to configure into the metro ring."
+    ::= { snMetroRingEntry 8 }
+
+snMetroRingName OBJECT-TYPE
+    SYNTAX     DisplayString
+    MAX-ACCESS read-write
+    STATUS     current
+    DESCRIPTION
+            "The metro ring description."
+    ::= { snMetroRingEntry 9 }
+
+snMetroRingRowStatus OBJECT-TYPE
+    SYNTAX     INTEGER {
+                 other(1),
+                 valid(2),
+                 delete(3),
+                 create(4)
+               }
+    MAX-ACCESS read-write
+    STATUS     current
+    DESCRIPTION
+            "This object is used to create and delete row in the
+            table and control if they are used. The values that
+            can be written are:
+            delete(3)...deletes the row
+            create(4)...creates a new row
+
+            If the row exists, then a SET with value of create(4)
+            returns error 'badValue'. Deleted rows go away immediately.
+            The following values can be returned on reads:
+            noSuchName...no such row
+            other(1).....some other cases
+            valid(2)....the row exists and is valid"
+    ::= { snMetroRingEntry 10 }
+
+snMetroRingOperState OBJECT-TYPE
+    SYNTAX     INTEGER { other(1), enabled(2), disabled(3) }
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+            "Metro ring operational state."
+    ::= { snMetroRingEntry 11 }
+
+snMetroRingTopoGroupId OBJECT-TYPE
+    SYNTAX     Integer32
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+            "Topology group ID that controls the metro ring."
+    ::= { snMetroRingEntry 12 }
+
+snMetroRingRHPTransmitted OBJECT-TYPE
+    SYNTAX     Counter32
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+            "Ring health protocol (RHP) transmitted counter."
+    ::= { snMetroRingEntry 13 }
+
+snMetroRingRHPReceived OBJECT-TYPE
+    SYNTAX     Counter32
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+            "Ring health protocol (RHP) received counter."
+    ::= { snMetroRingEntry 14 }
+
+snMetroRingStateChanged OBJECT-TYPE
+    SYNTAX     Counter32
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+            "Ring state changed counter."
+    ::= { snMetroRingEntry 15 }
+
+snMetroRingTCRBPDUReceived OBJECT-TYPE
+    SYNTAX     Counter32
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+            "Topology change protocol received counter."
+    ::= { snMetroRingEntry 16 }
+
+snMetroRingPriPort OBJECT-TYPE
+    SYNTAX     InterfaceIndex
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+            "The ifIndex value of primary port."
+    ::= { snMetroRingEntry 17 }
+
+snMetroRingSecPort OBJECT-TYPE
+    SYNTAX     InterfaceIndex
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+            "The ifIndex value of secondary port."
+    ::= { snMetroRingEntry 18 }
+
+snMetroRingPriPortState OBJECT-TYPE
+    SYNTAX     INTEGER {
+                 other(1),
+                 preforwarding(2),
+                 forwarding(3),
+                 blocking(4),
+                 disabled(5)
+               }
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+            "Metro ring primary port state.
+            other(1)...........none of the cases in below.
+            preforwarding(2)...port transmits RHP packets,
+                               port does not transmit data packets.
+            forwarding(3)......port transmits RHP and data packets.
+            blocking(4)........port receives RHP packets,
+                               port does not receive data packets.
+            disabled(5)........port is disabled from metro ring."
+    ::= { snMetroRingEntry 19 }
+
+snMetroRingSecPortState OBJECT-TYPE
+    SYNTAX     INTEGER {
+                 other(1),
+                 preforwarding(2),
+                 forwarding(3),
+                 blocking(4),
+                 disabled(5)
+               }
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+            "Metro ring secondary port state.
+            other(1)...........none of the cases in below.
+            preforwarding(2)...port transmits RHP packets,
+                               port does not transmit data packets.
+            forwarding(3)......port transmits RHP and data packets.
+            blocking(4)........port receives RHP packets,
+                               port does not receive data packets.
+            disabled(5)........port is disabled from metro ring."
+    ::= { snMetroRingEntry 20 }
+
+snMetroRingPriPortType OBJECT-TYPE
+    SYNTAX     INTEGER { other(1), regular(2), tunnel(3) }
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+            "Metro ring primary port type.
+            other(1).....none of the cases in below.
+            regular(2)...port is configured to operate on a single ring.
+            tunnel(3)....port is configured to operate on multiple rings."
+    ::= { snMetroRingEntry 21 }
+
+snMetroRingSecPortType OBJECT-TYPE
+    SYNTAX     INTEGER { other(1), regular(2), tunnel(3) }
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+            "Metro ring secondary port type.
+            other(1).....none of the cases in below.
+            regular(2)...port is configured to operate on a single ring.
+            tunnel(3)....port is configured to operate on multiple rings."
+    ::= { snMetroRingEntry 22 }
+
+snMetroRingPriPortActivePort OBJECT-TYPE
+    SYNTAX     InterfaceIndex
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+            "The ifIndex value of active primary port."
+    ::= { snMetroRingEntry 23 }
+
+snMetroRingSecPortActivePort OBJECT-TYPE
+    SYNTAX     InterfaceIndex
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+            "The ifIndex value of active secondary port."
+    ::= { snMetroRingEntry 24 }
+
+END

mibs/FOUNDRY-SN-STACKING-MIB

@@ -0,0 +1,435 @@
+FOUNDRY-SN-STACKING-MIB DEFINITIONS ::= BEGIN
+
+IMPORTS
+	MODULE-IDENTITY, OBJECT-TYPE, Integer32
+	  FROM SNMPv2-SMI
+	snSwitch
+		FROM FOUNDRY-SN-SWITCH-GROUP-MIB
+	MacAddress
+	  FROM SNMPv2-TC
+	DisplayString
+	  FROM FOUNDRY-SN-AGENT-MIB
+	InterfaceIndexOrZero
+	  FROM IF-MIB;
+snStacking MODULE-IDENTITY
+    LAST-UPDATED "201006020000Z"  -- 04 June 2010
+    ORGANIZATION "Brocade Communications Systems, Inc."
+    CONTACT-INFO
+             "Technical Support Center
+              130 Holger Way,
+              San Jose, CA  95134
+              Email:  ipsupport@brocade.com
+              Phone: 1-800-752-8061
+              URL:  www.brocade.com"
+    DESCRIPTION
+	      "Management Information for stacking system
+	       configuration and operational status.
+
+              Copyright 1996-2010 Brocade Communications Systems, Inc.
+              All rights reserved.
+              This Brocade Communications Systems SNMP Management Information Base Specification
+              embodies Brocade Communications Systems' confidential and proprietary
+              intellectual property. Brocade Communications Systems retains all
+              title and ownership in the Specification, including any revisions.
+
+              This Specification is supplied AS IS, and Brocade Communications Systems makes
+              no warranty, either express or implied, as to the use,
+              operation, condition, or performance of the specification, and any unintended
+              consequence it may on the user environment."
+
+    REVISION        "201006020000Z"  -- 04 June 2010
+    DESCRIPTION
+        "Changed the ORGANIZATION, CONTACT-INFO and DESCRIPTION fields."
+	REVISION     "200805050000Z" -- May 5, 2008
+	DESCRIPTION
+			""
+   ::= { snSwitch 31}
+
+
+--
+-- Stacking system
+--
+
+snStackingGlobalObjects OBJECT IDENTIFIER ::= { snStacking 1 }
+snStackingTableObjects  OBJECT IDENTIFIER ::= { snStacking 2 }
+
+--
+-- Stacking system Global Scalar Object Section
+--
+
+snStackingGlobalConfigState OBJECT-TYPE
+	SYNTAX     INTEGER {
+			  none(0),
+			  enabled(1),
+			  disabled(2)
+			}
+	MAX-ACCESS read-write
+	STATUS     current
+	DESCRIPTION
+		"Configure stack state for stacking feature on the global level.
+		 none: neutral, receive packets only
+		 enable: stacking is enable, send and receive packets
+		 disable: stacking is disable, No send and receive packets"
+	::= { snStackingGlobalObjects 1}
+
+snStackingGlobalMacAddress OBJECT-TYPE
+	SYNTAX     MacAddress
+	MAX-ACCESS read-write
+	STATUS     current
+	DESCRIPTION
+		"Management MAC address of the stacking system.
+		This is available to change management MAC address of stack
+		for administrative purpose. It is strongly recommended that this
+		command should be used with upmost caution to prevent duplicate
+		MAC address and must reboot the system to take an effect.
+		It is mutually exclusive from enabling the persistent MAC timer.
+		Enter zero MAC address to remove the configured MAC address"
+	::= { snStackingGlobalObjects 2 }
+
+snStackingGlobalPersistentMacTimerState OBJECT-TYPE
+	SYNTAX     INTEGER {
+			  enabled(0),
+			  disabled(1)
+			}
+	MAX-ACCESS read-write
+	STATUS     current
+	DESCRIPTION
+		"Configure persistent MAC timer state for stacking feature on the global level.
+		 enable: the persistent MAC timer is active and configured. The persistent MAC
+					  timer is set as the default timer (60 minutes)
+		 disable: deactivate the persistent MAC timer. It will stop the use of persistent MAC
+					  address and use new active stack unit's base MAC address "
+	::= { snStackingGlobalObjects 3}
+
+snStackingGlobalPersistentMacTimer OBJECT-TYPE
+	SYNTAX     Integer32
+	MAX-ACCESS read-write
+	STATUS     current
+	DESCRIPTION
+		"Persistent MAC timer in minutes for the stacking system
+		Number of minutes to retain original active stack unit's base MAC address in event of
+		active unit crash or removal. This timer is triggered when new active unit is elected.
+		When timer expires, new active unit will change stacking MAC to its own base MAC
+		address and advertise its own base MAC address to management VLAN to update the
+		ARP table of peers. If you decide to use new active unit's MAC address, one must enter
+		this timer again to reactivate the persistent MAC.
+				  0 - keep it forever.
+				  5  to 3600 - valid value range.
+				  60 - default value."
+	::= { snStackingGlobalObjects 4 }
+
+snStackingGlobalTopology OBJECT-TYPE
+	SYNTAX     INTEGER {
+			  other(1),
+				 chain(2),
+				 ring(3),
+				 standalone(4)
+			   }
+	MAX-ACCESS read-only
+	STATUS     current
+	DESCRIPTION
+		"The topology of the stacking system "
+	::= { snStackingGlobalObjects 5 }
+
+--
+-- Stacking system Table Object Section
+--
+
+--
+-- Stacking configuration unit Table
+-- Use this table to display and configure stacking related information for each unit
+--
+
+snStackingConfigUnitTable OBJECT-TYPE
+	SYNTAX     SEQUENCE OF SnStackingConfigUnitEntry
+	MAX-ACCESS not-accessible
+	STATUS     current
+	DESCRIPTION
+		"Stacking configuration unit table."
+	::= { snStackingTableObjects 1 }
+
+snStackingConfigUnitEntry OBJECT-TYPE
+	SYNTAX     SnStackingConfigUnitEntry
+	MAX-ACCESS not-accessible
+	STATUS     current
+	DESCRIPTION
+		"An entry in the stacking configuration table."
+	INDEX { snStackingConfigUnitIndex }
+	::= { snStackingConfigUnitTable 1 }
+
+SnStackingConfigUnitEntry ::= SEQUENCE {
+	snStackingConfigUnitIndex                          Integer32,
+	snStackingConfigUnitPriority                       Integer32,
+	snStackingConfigUnitConfigStackPort          InterfaceIndexOrZero,
+	snStackingConfigUnitRowStatus                  INTEGER,
+	snStackingConfigUnitType                          DisplayString,
+	snStackingConfigUnitState                          INTEGER,
+	snStackingConfigUnitStackPort1                  InterfaceIndexOrZero,
+	snStackingConfigUnitStackPort2                  InterfaceIndexOrZero
+}
+
+snStackingConfigUnitIndex OBJECT-TYPE
+	SYNTAX Integer32
+	MAX-ACCESS not-accessible
+	STATUS     current
+	DESCRIPTION
+		"The stacking unit Id"
+	::= { snStackingConfigUnitEntry 1 }
+
+ snStackingConfigUnitPriority OBJECT-TYPE
+	SYNTAX     Integer32 (0..255)
+	MAX-ACCESS read-write
+	STATUS     current
+	DESCRIPTION
+		"The priority in Active/backup eclection."
+	::= { snStackingConfigUnitEntry 2 }
+
+ snStackingConfigUnitConfigStackPort OBJECT-TYPE
+	SYNTAX		InterfaceIndexOrZero
+	MAX-ACCESS  read-write
+	STATUS     current
+	DESCRIPTION
+		"The IfIndex for the configured stacking port. If no
+		stacking port is configured, it will be displayed zero
+		and the first  two 10G ports as the default stacking ports.
+		Enter zero to remove the configured stacking port. "
+	::= { snStackingConfigUnitEntry 3 }
+
+snStackingConfigUnitRowStatus OBJECT-TYPE
+	SYNTAX     INTEGER {
+				 other(1),
+				 valid(2),
+				 delete(3)
+		  --       create(4)
+			   }
+	MAX-ACCESS read-write
+	STATUS     current
+	DESCRIPTION
+			"This object is used to delete row in the
+			table and control if they are used. The values that
+			can be written are:
+			delete(3)...deletes the row
+
+			If the row exists, then a SET with value of create(4)
+			returns error 'wrongValue'. Deleted rows go away immediately.
+			The following values can be returned on reads:
+			noSuchName...no such row
+			other(1).....some other cases
+			valid(2)....the row exists and is valid"
+	::= { snStackingConfigUnitEntry 4 }
+
+
+snStackingConfigUnitType OBJECT-TYPE
+	SYNTAX	DisplayString
+	MAX-ACCESS read-only
+	   STATUS     current
+	DESCRIPTION
+		"A description of the configured/active system type for each unit."
+	::= { snStackingConfigUnitEntry 5 }
+
+snStackingConfigUnitState OBJECT-TYPE
+	SYNTAX     INTEGER {
+				 local(1),
+				 remote(2),
+				 reserved(3),
+				 empty(4)
+			   }
+	MAX-ACCESS read-only
+	STATUS     current
+	DESCRIPTION
+		"A state for each unit "
+	::= { snStackingConfigUnitEntry 6 }
+
+ snStackingConfigUnitStackPort1 OBJECT-TYPE
+	SYNTAX		InterfaceIndexOrZero
+	MAX-ACCESS read-only
+	STATUS     current
+	DESCRIPTION
+		"First stack port for each unit. It returns 0 if stack port does not exist."
+	::= { snStackingConfigUnitEntry 7 }
+
+
+ snStackingConfigUnitStackPort2 OBJECT-TYPE
+	SYNTAX		InterfaceIndexOrZero
+	MAX-ACCESS read-only
+	STATUS     current
+	DESCRIPTION
+		"Second stack port for each unit. It returns 0 if stack port does not exist."
+	::= { snStackingConfigUnitEntry 8 }
+
+--
+-- Stacking operation unit Table
+-- Use this table to display stacking related information for each operational unit
+--
+
+snStackingOperUnitTable OBJECT-TYPE
+	SYNTAX     SEQUENCE OF SnStackingOperUnitEntry
+	MAX-ACCESS not-accessible
+	STATUS     current
+	DESCRIPTION
+		"Stacking operation unit table."
+	::= { snStackingTableObjects 2 }
+
+snStackingOperUnitEntry OBJECT-TYPE
+	SYNTAX     SnStackingOperUnitEntry
+	MAX-ACCESS not-accessible
+	STATUS     current
+	DESCRIPTION
+		"An entry in the stacking operation table."
+	INDEX { snStackingOperUnitIndex }
+	::= { snStackingOperUnitTable 1 }
+
+SnStackingOperUnitEntry ::= SEQUENCE {
+	snStackingOperUnitIndex                    Integer32,
+	snStackingOperUnitRole                     INTEGER,
+	snStackingOperUnitMac                      MacAddress,
+	snStackingOperUnitPriority                 Integer32,
+	snStackingOperUnitState                    INTEGER,
+	snStackingOperUnitDescription            DisplayString,
+	snStackingOperUnitStackPort1            InterfaceIndexOrZero,
+	snStackingOperUnitStackPort1State     INTEGER,
+	snStackingOperUnitStackPort2            InterfaceIndexOrZero,
+	snStackingOperUnitStackPort2State     INTEGER,
+	snStackingOperUnitNeighbor1             Integer32,
+	snStackingOperUnitNeighbor2             Integer32,
+	snStackingOperUnitImgVer                 DisplayString,
+	snStackingOperUnitBuildlVer               DisplayString
+
+}
+
+snStackingOperUnitIndex OBJECT-TYPE
+	SYNTAX     Integer32
+	MAX-ACCESS not-accessible
+	STATUS     current
+	DESCRIPTION
+		"The stacking unit Id"
+	::= { snStackingOperUnitEntry 1 }
+
+ snStackingOperUnitRole OBJECT-TYPE
+	SYNTAX     INTEGER {
+			  other(1),
+				 active(2),
+				 standby(3),
+				 member(4),
+				 standalone(5)
+			   }
+	MAX-ACCESS read-only
+	STATUS     current
+	DESCRIPTION
+		"A role for each unit "
+	::= { snStackingOperUnitEntry 2 }
+
+snStackingOperUnitMac OBJECT-TYPE
+	SYNTAX     MacAddress
+	MAX-ACCESS read-only
+	STATUS     current
+	DESCRIPTION
+		"A MAC address for each unit"
+	::= { snStackingOperUnitEntry 3 }
+
+snStackingOperUnitPriority OBJECT-TYPE
+	SYNTAX     Integer32 (0..255)
+	MAX-ACCESS read-only
+	STATUS     current
+	DESCRIPTION
+		"The priority in Active/backup eclection."
+	::= { snStackingOperUnitEntry 4 }
+
+ snStackingOperUnitState OBJECT-TYPE
+	SYNTAX     INTEGER {
+				 local(1),
+				 remote(2),
+				 reserved(3),
+				 empty(4)
+			   }
+	MAX-ACCESS read-only
+	STATUS     current
+	DESCRIPTION
+		"A state for each unit "
+	::= { snStackingOperUnitEntry 5}
+
+ snStackingOperUnitDescription OBJECT-TYPE
+	SYNTAX		DisplayString (SIZE (0..128))
+	MAX-ACCESS read-only
+	STATUS     current
+	DESCRIPTION
+		"Describes the stacking state for each unit."
+	::= { snStackingOperUnitEntry 6 }
+
+ snStackingOperUnitStackPort1 OBJECT-TYPE
+	SYNTAX		InterfaceIndexOrZero
+	MAX-ACCESS read-only
+	STATUS     current
+	DESCRIPTION
+		"First stack port for each unit. It returns 0 if stack port does not exist."
+	::= { snStackingOperUnitEntry 7 }
+
+ snStackingOperUnitStackPort1State OBJECT-TYPE
+	SYNTAX     INTEGER {
+		other(1),
+		up(2),
+		down(3)
+	}
+	MAX-ACCESS read-only
+	STATUS     current
+	DESCRIPTION
+		"The first stack port state for each unit. "
+	::= { snStackingOperUnitEntry 8 }
+
+
+ snStackingOperUnitStackPort2 OBJECT-TYPE
+	SYNTAX		InterfaceIndexOrZero
+	MAX-ACCESS read-only
+	STATUS     current
+	DESCRIPTION
+		"Second stack port for each unit. It returns 0 if stack port does not exist."
+	::= { snStackingOperUnitEntry 9 }
+
+ snStackingOperUnitStackPort2State OBJECT-TYPE
+	SYNTAX     INTEGER {
+		other(1),
+		up(2),
+		down(3)
+	}
+	MAX-ACCESS read-only
+	STATUS     current
+	DESCRIPTION
+		"The second stack port state for each unit. "
+	::= { snStackingOperUnitEntry 10 }
+
+ snStackingOperUnitNeighbor1 OBJECT-TYPE
+	SYNTAX		 Integer32
+	MAX-ACCESS read-only
+	STATUS     current
+	DESCRIPTION
+	"Stacking neighbor unit (left) number.
+	If there is no neighbor unit, then it returns 0."
+
+	::= { snStackingOperUnitEntry 11 }
+
+ snStackingOperUnitNeighbor2 OBJECT-TYPE
+	SYNTAX		Integer32
+	MAX-ACCESS read-only
+	STATUS     current
+	DESCRIPTION
+	"Stacking neighbor unit (left) number.
+	If there is no neighbor unit, then it returns 0."
+	::= { snStackingOperUnitEntry 12 }
+
+snStackingOperUnitImgVer OBJECT-TYPE
+	SYNTAX		DisplayString (SIZE (0..32))
+	MAX-ACCESS read-only
+	STATUS     current
+	DESCRIPTION
+		"The version of the running software image"
+	::= { snStackingOperUnitEntry 13 }
+
+snStackingOperUnitBuildlVer OBJECT-TYPE
+	SYNTAX		DisplayString (SIZE (0..32))
+	MAX-ACCESS read-only
+	STATUS     current
+	DESCRIPTION
+		"The version of the running software build"
+	::= { snStackingOperUnitEntry 14 }
+
+END

mibs/FOUNDRY-VLAN-CAR-MIB

@@ -1,256 +1,279 @@
--- *****************************************************************
--- Foundry Commited Access Rate MIB file.
--- *****************************************************************
-FOUNDRY-VLAN-CAR-MIB DEFINITIONS ::= BEGIN
-
-IMPORTS
-	OBJECT-TYPE,
-	Gauge
-		FROM RFC1155-SMI
-
-        Counter64
-		FROM SNMPv2-SMI
-
-        PacketSource, RateLimitType, RateLimitAction
-		FROM FOUNDRY-CAR-MIB  
-
-  	snVLanCAR
-  		FROM FOUNDRY-SN-SWITCH-GROUP-MIB;
-	
-
-
-snVLanCARs	OBJECT IDENTIFIER ::= { snVLanCAR 1 }
-
-
-
-snVLanCARTable OBJECT-TYPE
-	SYNTAX  SEQUENCE OF SnVLanCAREntry
-	ACCESS  not-accessible
-        STATUS  mandatory
-        DESCRIPTION
-        "A table of rate limit configuration entries for a vlan.
-	Rate Limit is a method of traffic control.  It allows a set
-	of rate limits to be configured and applied to packets flowing
-	into/out of an interface to regulate network traffic."
-
-        ::= { snVLanCARs 1 }
-
-
-snVLanCAREntry OBJECT-TYPE
-        SYNTAX SnVLanCAREntry
-        ACCESS  not-accessible
-        STATUS  mandatory
-        DESCRIPTION
-        	"A collection of rate-limit configuration objects on this 
-		vlan."
-        INDEX { snVLanCARVLanId, snVLanCARDirection, snVLanCARRowIndex }
-        ::= { snVLanCARTable 1 }
-
-SnVLanCAREntry ::=
-	SEQUENCE {
-		snVLanCARDirection
-               		PacketSource,
-		snVLanCARVLanId
-                        INTEGER,
-		snVLanCARRowIndex
-                        INTEGER,
-		snVLanCARType
-                        RateLimitType,
-		snVLanCARAccIdx
-                        INTEGER,
-		snVLanCARRate
-                        INTEGER,
-		snVLanCARLimit
-                        INTEGER,
-		snVLanCARExtLimit
-                        INTEGER,
-		snVLanCARConformAction
-			RateLimitAction,
-		snVLanCARExceedAction
-       			RateLimitAction,
-		snVLanCARStatSwitchedPkts
-                        Counter64,
-		snVLanCARStatSwitchedBytes
-                        Counter64,
-		snVLanCARStatFilteredPkts
-                        Counter64,
-		snVLanCARStatFilteredBytes
-                        Counter64,
-		snVLanCARStatCurBurst
-       			Gauge
-	}
-
---need to refer to the vlan table
---index once it is changed to single
---vlan id as the row index
-
-snVLanCARVLanId OBJECT-TYPE
-	SYNTAX  INTEGER (1..4095)
-	ACCESS  read-only
-	STATUS  mandatory
-	DESCRIPTION
-		"The VLAN ID as one of the indices of this table .
-		 Each VLAN ID can have a membership of multiple 
-		 ports."
-	::= { snVLanCAREntry 1 }
-
-snVLanCARDirection OBJECT-TYPE
-	SYNTAX  PacketSource
-        ACCESS  read-only
-        STATUS  mandatory
-        DESCRIPTION
-       		"The input or output transmission direction for the 
-                Rate Limit object."
-        ::= { snVLanCAREntry 2 }
-
-snVLanCARRowIndex OBJECT-TYPE
-	SYNTAX  INTEGER (1..2147483647)
-        ACCESS  read-only
-        STATUS  mandatory
-        DESCRIPTION
-                "The table index for rate limit objects.
-		It increases as the rate limit entries are added.
-		Skips the number when a row is deleted."
-
-        ::= { snVLanCAREntry 3 }
-
-snVLanCARType OBJECT-TYPE
-	SYNTAX  RateLimitType
-        ACCESS  read-only
-        STATUS  mandatory
-        DESCRIPTION
-		"The type of traffic rate-limited against."
-
-	::= { snVLanCAREntry 4 }
-
-snVLanCARAccIdx OBJECT-TYPE
-	SYNTAX  INTEGER
-        ACCESS  read-only
-        STATUS  mandatory
-        DESCRIPTION
-		"The index to the access list if RateLimitType is either
-		quickAcc or standardAcc."
-
-	::= { snVLanCAREntry 5 }
-
-snVLanCARRate OBJECT-TYPE
-	SYNTAX  INTEGER
-        ACCESS  read-only
-        STATUS  mandatory
-        DESCRIPTION
-		"The comitted access rate. This determines the long term
-		average transmission rate. Traffic that falls under this
-		rate always conforms. This is average rate in bits per 
-		second."
-
-	::= { snVLanCAREntry 6 }
-
-snVLanCARLimit OBJECT-TYPE
-	SYNTAX  INTEGER
-        ACCESS  read-only
-        STATUS  mandatory
-        DESCRIPTION
-		"This is the normal burst size that determines how large traffic
-		bursts can be before some traffic exceeds the rate limit. This
-		specifies the number of bytes that are guaranteed to be transported
-		by the network at the average rate under normal conditions during
-		committed time interval. This normal burst size is in bytes."
-
-	::= { snVLanCAREntry 7 }
-
-snVLanCARExtLimit OBJECT-TYPE
-	SYNTAX  INTEGER
-	ACCESS  read-only
-	STATUS  mandatory
-	DESCRIPTION
-		"This is the extended burst limit that determines how large traffic
-		bursts can be before all the traffic exceeds the rate limit. This
-		burst size is in bytes. "
-
-	::= { snVLanCAREntry 8 }
-
-snVLanCARConformAction OBJECT-TYPE
-	SYNTAX	RateLimitAction
-	ACCESS  read-only
-	STATUS	mandatory
-	DESCRIPTION
-		"Action to be taken when the traffic is within
-		the Rate Limit.
-		drop		drop the packet.
-		xmit		transmit the packet.
-		continue	continue to evaluate to the subsequent
-					rate limits.
-		precedXmit	rewrite the IP precedence and transmit
-					the packet.
-		precedCont	rewrite the IP precedence and allow it
-					evaluated by subsequent rate limits."
-
-	::= { snVLanCAREntry 9 }
-
-snVLanCARExceedAction OBJECT-TYPE
-	SYNTAX	RateLimitAction
-	ACCESS  read-only
-	STATUS	mandatory
-	DESCRIPTION
-		"Action to be taken when the traffic exceeds
-		the Rate Limit.
-   		drop		drop the packet.
-		xmit		transmit the packet.
-		continue	continue to evaluate to the subsequent
-					rate limits.
-		precedXmit	rewrite the IP precedence and transmit
-					the packet.
-		precedCont	rewrite the IP precedence and allow it
-					evaluated by subsequent rate limits."
-
-	::= { snVLanCAREntry 10 }
-
-snVLanCARStatSwitchedPkts OBJECT-TYPE
-	SYNTAX  Counter64
-	ACCESS  read-only
-	STATUS  mandatory
-	DESCRIPTION
-		"The counter of packets permitted by this rate limit."
-
-	::= { snVLanCAREntry 11 }
-
-snVLanCARStatSwitchedBytes OBJECT-TYPE
-	SYNTAX  Counter64
-	ACCESS  read-only
-	STATUS  mandatory
-	DESCRIPTION
-		"The counter of bytes permitted by this interface."
-
-	::= { snVLanCAREntry 12 }
-
-snVLanCARStatFilteredPkts OBJECT-TYPE
-	SYNTAX  Counter64
-	--UNITS	"packets"
-	ACCESS  read-only
-	STATUS  mandatory
-	DESCRIPTION
-		"The counter of packets which exceeded this rate limit."
-
-	::= { snVLanCAREntry 13 }
-
-snVLanCARStatFilteredBytes OBJECT-TYPE
-	SYNTAX  Counter64
-	ACCESS  read-only
-	STATUS  mandatory
-	DESCRIPTION
-		"The counter of bytes which exceeded this rate limit."
-
-	::= { snVLanCAREntry 14 }
-
-snVLanCARStatCurBurst OBJECT-TYPE
-	SYNTAX  Gauge
-	ACCESS  read-only
-	STATUS  mandatory
-	DESCRIPTION
-		"The current received burst size."
-	::= { snVLanCAREntry 15 }
-
--- end of snVLanCARTable
-
-
-END
+FOUNDRY-VLAN-CAR-MIB DEFINITIONS ::= BEGIN
+
+IMPORTS
+
+	MODULE-IDENTITY, OBJECT-TYPE,Gauge32, Counter64,Integer32
+		FROM SNMPv2-SMI
+	snSwitch
+		FROM FOUNDRY-SN-SWITCH-GROUP-MIB
+	PacketSource, RateLimitType, RateLimitAction
+		FROM FOUNDRY-CAR-MIB;
+
+
+
+snVLanCAR MODULE-IDENTITY
+    LAST-UPDATED "201006020000Z"  -- 04 June 2010
+    ORGANIZATION "Brocade Communications Systems, Inc."
+    CONTACT-INFO
+             "Technical Support Center
+              130 Holger Way,
+              San Jose, CA  95134
+              Email:  ipsupport@brocade.com
+              Phone: 1-800-752-8061
+              URL:  www.brocade.com"
+    DESCRIPTION
+             "Copyright 1996-2010 Brocade Communications Systems, Inc.
+              All rights reserved.
+              This Brocade Communications Systems SNMP Management Information Base Specification
+              embodies Brocade Communications Systems' confidential and proprietary
+              intellectual property. Brocade Communications Systems retains all
+              title and ownership in the Specification, including any revisions.
+
+              This Specification is supplied AS IS, and Brocade Communications Systems makes
+              no warranty, either express or implied, as to the use,
+              operation, condition, or performance of the specification, and any unintended
+              consequence it may on the user environment."
+
+    REVISION        "201006020000Z"  -- 04 June 2010
+    DESCRIPTION
+        "Changed the ORGANIZATION, CONTACT-INFO and DESCRIPTION fields."
+
+    REVISION     "200909300000Z" -- September 30, 2009
+    DESCRIPTION
+			"convert from SMIv1 to SMIv2"
+   ::= {snSwitch  17}
+snVLanCARs	OBJECT IDENTIFIER ::= { snVLanCAR 1 }
+
+
+
+snVLanCARTable OBJECT-TYPE
+	SYNTAX  SEQUENCE OF SnVLanCAREntry
+	MAX-ACCESS  not-accessible
+		STATUS  current
+		DESCRIPTION
+		"A table of rate limit configuration entries for a vlan.
+	Rate Limit is a method of traffic control.  It allows a set
+	of rate limits to be configured and applied to packets flowing
+	into/out of an interface to regulate network traffic."
+
+		::= { snVLanCARs 1 }
+
+
+snVLanCAREntry OBJECT-TYPE
+		SYNTAX SnVLanCAREntry
+		MAX-ACCESS  not-accessible
+		STATUS  current
+		DESCRIPTION
+			"A collection of rate-limit configuration objects on this
+		vlan."
+		INDEX { snVLanCARVLanId, snVLanCARDirection, snVLanCARRowIndex }
+		::= { snVLanCARTable 1 }
+
+SnVLanCAREntry ::=
+	SEQUENCE {
+		snVLanCARDirection
+					PacketSource,
+		snVLanCARVLanId
+						INTEGER,
+		snVLanCARRowIndex
+						INTEGER,
+		snVLanCARType
+						RateLimitType,
+		snVLanCARAccIdx
+						Integer32,
+		snVLanCARRate
+						Integer32,
+		snVLanCARLimit
+						Integer32,
+		snVLanCARExtLimit
+						Integer32,
+		snVLanCARConformAction
+			RateLimitAction,
+		snVLanCARExceedAction
+				RateLimitAction,
+		snVLanCARStatSwitchedPkts
+						Counter64,
+		snVLanCARStatSwitchedBytes
+						Counter64,
+		snVLanCARStatFilteredPkts
+						Counter64,
+		snVLanCARStatFilteredBytes
+						Counter64,
+		snVLanCARStatCurBurst
+				Gauge32
+	}
+
+--need to refer to the vlan table
+--index once it is changed to single
+--vlan id as the row index
+
+snVLanCARVLanId OBJECT-TYPE
+	SYNTAX  INTEGER (1..4095)
+	MAX-ACCESS  read-only
+	STATUS  current
+	DESCRIPTION
+		"The VLAN ID as one of the indices of this table .
+		 Each VLAN ID can have a membership of multiple
+		 ports."
+	::= { snVLanCAREntry 1 }
+
+snVLanCARDirection OBJECT-TYPE
+	SYNTAX  PacketSource
+		MAX-ACCESS  read-only
+		STATUS  current
+		DESCRIPTION
+			"The input or output transmission direction for the
+				Rate Limit object."
+		::= { snVLanCAREntry 2 }
+
+snVLanCARRowIndex OBJECT-TYPE
+	SYNTAX  INTEGER (1..2147483647)
+		MAX-ACCESS  read-only
+		STATUS  current
+		DESCRIPTION
+				"The table index for rate limit objects.
+		It increases as the rate limit entries are added.
+		Skips the number when a row is deleted."
+
+		::= { snVLanCAREntry 3 }
+
+snVLanCARType OBJECT-TYPE
+	SYNTAX  RateLimitType
+		MAX-ACCESS  read-only
+		STATUS  current
+		DESCRIPTION
+		"The type of traffic rate-limited against."
+
+	::= { snVLanCAREntry 4 }
+
+snVLanCARAccIdx OBJECT-TYPE
+	SYNTAX  Integer32
+		MAX-ACCESS  read-only
+		STATUS  current
+		DESCRIPTION
+		"The index to the access list if RateLimitType is either
+		quickAcc or standardAcc."
+
+	::= { snVLanCAREntry 5 }
+
+snVLanCARRate OBJECT-TYPE
+	SYNTAX  Integer32
+		MAX-ACCESS  read-only
+		STATUS  current
+		DESCRIPTION
+		"The comitted access rate. This determines the long term
+		average transmission rate. Traffic that falls under this
+		rate always conforms. This is average rate in bits per
+		second."
+
+	::= { snVLanCAREntry 6 }
+
+snVLanCARLimit OBJECT-TYPE
+	SYNTAX  Integer32
+		MAX-ACCESS  read-only
+		STATUS  current
+		DESCRIPTION
+		"This is the normal burst size that determines how large traffic
+		bursts can be before some traffic exceeds the rate limit. This
+		specifies the number of bytes that are guaranteed to be transported
+		by the network at the average rate under normal conditions during
+		committed time interval. This normal burst size is in bytes."
+
+	::= { snVLanCAREntry 7 }
+
+snVLanCARExtLimit OBJECT-TYPE
+	SYNTAX  Integer32
+	MAX-ACCESS  read-only
+	STATUS  current
+	DESCRIPTION
+		"This is the extended burst limit that determines how large traffic
+		bursts can be before all the traffic exceeds the rate limit. This
+		burst size is in bytes. "
+
+	::= { snVLanCAREntry 8 }
+
+snVLanCARConformAction OBJECT-TYPE
+	SYNTAX	RateLimitAction
+	MAX-ACCESS  read-only
+	STATUS	current
+	DESCRIPTION
+		"Action to be taken when the traffic is within
+		the Rate Limit.
+		drop		drop the packet.
+		xmit		transmit the packet.
+		continue	continue to evaluate to the subsequent
+					rate limits.
+		precedXmit	rewrite the IP precedence and transmit
+					the packet.
+		precedCont	rewrite the IP precedence and allow it
+					evaluated by subsequent rate limits."
+
+	::= { snVLanCAREntry 9 }
+
+snVLanCARExceedAction OBJECT-TYPE
+	SYNTAX	RateLimitAction
+	MAX-ACCESS  read-only
+	STATUS	current
+	DESCRIPTION
+		"Action to be taken when the traffic exceeds
+		the Rate Limit.
+		drop		drop the packet.
+		xmit		transmit the packet.
+		continue	continue to evaluate to the subsequent
+					rate limits.
+		precedXmit	rewrite the IP precedence and transmit
+					the packet.
+		precedCont	rewrite the IP precedence and allow it
+					evaluated by subsequent rate limits."
+
+	::= { snVLanCAREntry 10 }
+
+snVLanCARStatSwitchedPkts OBJECT-TYPE
+	SYNTAX  Counter64
+	MAX-ACCESS  read-only
+	STATUS  current
+	DESCRIPTION
+		"The counter of packets permitted by this rate limit."
+
+	::= { snVLanCAREntry 11 }
+
+snVLanCARStatSwitchedBytes OBJECT-TYPE
+	SYNTAX  Counter64
+	MAX-ACCESS  read-only
+	STATUS  current
+	DESCRIPTION
+		"The counter of bytes permitted by this interface."
+
+	::= { snVLanCAREntry 12 }
+
+snVLanCARStatFilteredPkts OBJECT-TYPE
+	SYNTAX  Counter64
+	--UNITS	"packets"
+	MAX-ACCESS  read-only
+	STATUS  current
+	DESCRIPTION
+		"The counter of packets which exceeded this rate limit."
+
+	::= { snVLanCAREntry 13 }
+
+snVLanCARStatFilteredBytes OBJECT-TYPE
+	SYNTAX  Counter64
+	MAX-ACCESS  read-only
+	STATUS  current
+	DESCRIPTION
+		"The counter of bytes which exceeded this rate limit."
+
+	::= { snVLanCAREntry 14 }
+
+snVLanCARStatCurBurst OBJECT-TYPE
+	SYNTAX  Gauge32
+	MAX-ACCESS  read-only
+	STATUS  current
+	DESCRIPTION
+		"The current received burst size."
+	::= { snVLanCAREntry 15 }
+
+-- end of snVLanCARTable
+
+
+END

mibs/Foundry-MPLS-MIB

@@ -0,0 +1,731 @@
+Foundry-MPLS-MIB DEFINITIONS ::= BEGIN
+
+-- SECTION 1: Top Level Definitions
+
+-- Imports
+
+IMPORTS
+    MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE,
+    Unsigned32, Counter32, Counter64, IpAddress, Integer32
+        FROM SNMPv2-SMI
+    DisplayString, TimeStamp, RowStatus
+        FROM SNMPv2-TC
+    snMpls, snTraps
+        FROM FOUNDRY-SN-ROOT-MIB
+    TruthValue,TEXTUAL-CONVENTION
+	 FROM SNMPv2-TC
+    ClassOfService
+        FROM FDRY-MPLS-L2VPN-MIB
+    MplsTunnelAffinity
+        FROM MPLS-TC-STD-MIB
+    AreaID
+        FROM FOUNDRY-SN-OSPF-GROUP-MIB;
+
+
+mpls MODULE-IDENTITY
+    LAST-UPDATED "201006020000Z"  -- 04 June 2010
+    ORGANIZATION "Brocade Communications Systems, Inc."
+    CONTACT-INFO
+             "Technical Support Center
+              130 Holger Way,
+              San Jose, CA  95134
+              Email:  ipsupport@brocade.com
+              Phone: 1-800-752-8061
+              URL:  www.brocade.com"
+    DESCRIPTION
+        "This is Brocade's proprietary MIB module for Multi-Protocol Label Switched Paths.
+
+        Copyright 1996-2010 Brocade Communications Systems, Inc.
+               All rights reserved.
+               This Brocade Communications Systems SNMP Management Information Base Specification
+               embodies Brocade Communications Systems' confidential and proprietary
+               intellectual property. Brocade Communications Systems retains all
+               title and ownership in the Specification, including any revisions.
+
+               This Specification is supplied AS IS, and Brocade Communications Systems makes
+               no warranty, either express or implied, as to the use,
+               operation, condition, or performance of the specification, and any unintended
+               consequence it may on the user environment."
+
+    REVISION        "201006020000Z"  -- 04 June 2010
+    DESCRIPTION
+        "Changed the ORGANIZATION, CONTACT-INFO and DESCRIPTION fields."
+
+    REVISION      "200802060000Z"		-- Feb 6, 2008
+    DESCRIPTION
+        "Add support for proprietary extensions to the VLL and VPLS mib."
+    ::= { snMpls 1 }
+
+mplsLspNotifications     OBJECT IDENTIFIER ::= { mpls 0 }
+mplsInfo      OBJECT IDENTIFIER ::= { mpls 1 }
+mplsLspInfo   OBJECT IDENTIFIER ::= { mpls 2 }
+mplsVllInfo   OBJECT IDENTIFIER ::= { mpls 3 }
+mplsVplsInfo   OBJECT IDENTIFIER ::= { mpls 4 }
+
+mplsVersion OBJECT-TYPE
+    SYNTAX     Unsigned32
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION "MPLS version number."
+    ::= { mplsInfo 1 }
+
+--
+-- Administrative groups, also known as resource classes or link colors,
+-- allows MPLS-enabled interfaces to be assigned to various classes.
+-- For ease of use to a user, a groupname can be associated to a single or
+-- multiple administrative group.
+-- Up to 32 administrative groups can be configured on the device.
+--
+
+brcdMplsAdminGroupTable OBJECT-TYPE
+    SYNTAX     SEQUENCE OF BrcdMplsAdminGroupEntry
+    MAX-ACCESS not-accessible
+    STATUS     current
+    DESCRIPTION
+        "List of administrative groups (by ID) that have a configured group name."
+    ::= { mplsInfo 2 }
+
+brcdMplsAdminGroupEntry OBJECT-TYPE
+    SYNTAX     BrcdMplsAdminGroupEntry
+    MAX-ACCESS not-accessible
+    STATUS     current
+    DESCRIPTION
+        "Information about an administrative group entry."
+    INDEX { brcdMplsAdminGroupId }
+    ::= { brcdMplsAdminGroupTable 1 }
+
+BrcdMplsAdminGroupEntry ::=
+    SEQUENCE {
+        brcdMplsAdminGroupId    		Unsigned32,
+        brcdMplsAdminGroupName  		DisplayString,
+        brcdMplsAdminGroupRowStatus  	RowStatus
+}
+
+brcdMplsAdminGroupId OBJECT-TYPE
+    SYNTAX     Unsigned32 (1..32)
+    MAX-ACCESS not-accessible
+    STATUS     current
+    DESCRIPTION
+        "Identifies the administrative group ID in 1-based.
+         The end user of this object must convert this to 0-based since this
+         maps to the bit position in the constraint-based link selection."
+    ::= { brcdMplsAdminGroupEntry 1 }
+
+brcdMplsAdminGroupName OBJECT-TYPE
+    SYNTAX     DisplayString (SIZE (1..32))
+    MAX-ACCESS read-create
+    STATUS     current
+    DESCRIPTION
+        "The group name that this administrative group is associated with."
+    ::= { brcdMplsAdminGroupEntry 2 }
+
+brcdMplsAdminGroupRowStatus OBJECT-TYPE
+    SYNTAX     RowStatus
+    MAX-ACCESS read-create
+    STATUS     current
+    DESCRIPTION
+        "The row status of an entry.
+         Note: Set request to this table is not supported in this release.
+         Always returns 'active' for the existing entries."
+    ::= { brcdMplsAdminGroupEntry 3 }
+
+
+--
+-- MPLS-enabled Interface Table
+--
+
+brcdMplsInterfaceTable OBJECT-TYPE
+    SYNTAX     SEQUENCE OF BrcdMplsInterfaceEntry
+    MAX-ACCESS not-accessible
+    STATUS     current
+    DESCRIPTION
+        "List of MPLS-enabled Interfaces."
+    ::= { mplsInfo 3 }
+
+brcdMplsInterfaceEntry OBJECT-TYPE
+    SYNTAX     BrcdMplsInterfaceEntry
+    MAX-ACCESS not-accessible
+    STATUS     current
+    DESCRIPTION
+        "Information about an MPLS interface entry."
+    INDEX { brcdMplsInterfaceIndex }
+    ::= { brcdMplsInterfaceTable 1 }
+
+BrcdMplsInterfaceEntry::=
+    SEQUENCE {
+        brcdMplsInterfaceIndex        	Unsigned32,
+        brcdMplsInterfaceAdminGroup   	MplsTunnelAffinity,
+        brcdMplsInterfaceRowStatus     	RowStatus
+}
+
+brcdMplsInterfaceIndex OBJECT-TYPE
+    SYNTAX     Unsigned32
+    MAX-ACCESS not-accessible
+    STATUS     current
+    DESCRIPTION
+        "The ifIndex of the MPLS-enabled port or VE interface."
+    ::= { brcdMplsInterfaceEntry 1 }
+
+brcdMplsInterfaceAdminGroup OBJECT-TYPE
+    SYNTAX     MplsTunnelAffinity
+    MAX-ACCESS read-create
+    STATUS     current
+    DESCRIPTION
+        "Specifies which administrative groups this MPLS-enabled
+         interface belongs to."
+    ::= { brcdMplsInterfaceEntry 2 }
+
+brcdMplsInterfaceRowStatus     OBJECT-TYPE
+    SYNTAX     RowStatus
+    MAX-ACCESS read-create
+    STATUS     current
+    DESCRIPTION
+        "The row status of an entry.
+         Note: Set request to this table is not supported in this release.
+         Always returns 'active' for the existing entries."
+    ::= { brcdMplsInterfaceEntry 3 }
+
+
+mplsConfiguredLsps OBJECT-TYPE
+    SYNTAX     Unsigned32
+    MAX-ACCESS read-only
+    STATUS     deprecated
+    DESCRIPTION "Number of configured LSPs. Sum of RSVP and static configured LSPs.
+                    DEPRECATED BY mplsTunnelConfigured IN rfc3812-MPLS-TE-STD-MIB."
+    ::= { mplsLspInfo 1 }
+
+mplsActiveLsps OBJECT-TYPE
+    SYNTAX     Unsigned32
+    MAX-ACCESS read-only
+    STATUS     deprecated
+    DESCRIPTION "Number of active LSPs. Sum of RSVP, LDP and static LSPs.
+                    DEPRECATED BY mplsTunnelActive IN rfc3812-MPLS-TE-STD-MIB."
+    ::= { mplsLspInfo 2 }
+
+
+--
+-- MPLS LSP Table
+--
+
+mplsLspTable OBJECT-TYPE
+    SYNTAX     SEQUENCE OF MplsLspEntry
+    MAX-ACCESS not-accessible
+    STATUS     current
+    DESCRIPTION "List of Configured Label Switched Paths."
+    ::= { mplsLspInfo 3 }
+
+mplsLspEntry OBJECT-TYPE
+    SYNTAX     MplsLspEntry
+    MAX-ACCESS not-accessible
+    STATUS     current
+    DESCRIPTION
+        "Entry containing information about a particular
+         Label Switched Path."
+    INDEX { mplsLspSignalingProto, mplsLspIndex }
+    ::= { mplsLspTable 1 }
+
+MplsLspEntry ::=
+    SEQUENCE {
+        mplsLspSignalingProto      	INTEGER,
+        mplsLspIndex            		Unsigned32,
+        mplsLspName             		DisplayString,
+        mplsLspState            		INTEGER,
+        mplsLspPackets          		Counter64,
+        mplsLspAge              		TimeStamp,
+        mplsLspTimeUp           		TimeStamp,
+        mplsLspPrimaryTimeUp    	TimeStamp,
+        mplsLspTransitions      		Counter32,
+        mplsLspLastTransition   	TimeStamp,
+        mplsLspFrom             		IpAddress,
+        mplsLspTo               		IpAddress,
+        mplsLspPathName               DisplayString,
+        mplsLspPathType                INTEGER,
+        mplsLspAdaptive             	TruthValue,
+        mplsLspBfdSessionId      	Unsigned32,
+        mplsLspReoptimizeTimer  	Unsigned32,
+        mplsLspCoS			   	ClassOfService,
+        mplsLspHopLimit			Unsigned32,
+        mplsLspCspf   			INTEGER,
+        mplsLspCspfTieBreaker		INTEGER,
+        mplsLspFrrMode			INTEGER,
+        mplsLspFrrSetupPriority	Unsigned32,
+        mplsLspFrrHoldingPriority	Unsigned32,
+        mplsLspFrrHopLimit		Unsigned32,
+        mplsLspFrrBandwidth		Unsigned32,
+        mplsLspFrrAdmGrpIncludeAny		MplsTunnelAffinity,
+        mplsLspFrrAdmGrpIncludeAll		MplsTunnelAffinity,
+        mplsLspFrrAdmGrpExcludeAny		MplsTunnelAffinity,
+        mplsLspPathSelectMode			INTEGER,
+        mplsLspPathSelectPathname              DisplayString,
+        mplsLspPathSelectRevertTimer		Unsigned32,
+        mplsLspShortcutOspfAllowed		TruthValue,
+        mplsLspShortcutIsisAllowed			TruthValue,
+        mplsLspShortcutIsisLevel			INTEGER,
+        mplsLspShortcutIsisAnnounce		TruthValue,
+        mplsLspShortcutIsisAnnounceMetric	Integer32,
+        mplsLspShortcutIsisRelativeMetric	Integer32
+}
+
+mplsLspSignalingProto OBJECT-TYPE
+    SYNTAX     INTEGER {
+        ldp(1),
+        rsvp(2)
+    }
+    MAX-ACCESS not-accessible
+    STATUS     current
+    DESCRIPTION "MPLS signaling protocol used by this LSP."
+    ::= { mplsLspEntry 1 }
+
+mplsLspIndex OBJECT-TYPE
+    SYNTAX     Unsigned32
+    MAX-ACCESS not-accessible
+    STATUS     current
+    DESCRIPTION "The unique index of the LSP in the system for a given signaling protocol."
+    ::= { mplsLspEntry 2 }
+
+mplsLspName OBJECT-TYPE
+    SYNTAX     DisplayString (SIZE (0..32))
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION "Name of the Label Switched Path."
+    ::= { mplsLspEntry 3 }
+
+mplsLspState OBJECT-TYPE
+    SYNTAX     INTEGER {
+               unknown(1),
+               up(2),
+               down(3)
+    }
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION "The operational state of the LSP."
+    ::= { mplsLspEntry 4 }
+
+mplsLspPackets OBJECT-TYPE
+    SYNTAX     Counter64
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+        "The number of egress Layer-3 VPN and IPoMPLS packets
+        meeting the in-label and tunnel criteria."
+    ::= { mplsLspEntry 5 }
+
+mplsLspAge OBJECT-TYPE
+    SYNTAX     TimeStamp
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+        "The age, since creation of this LSP in 10-millisecond periods."
+    ::= { mplsLspEntry 6 }
+
+mplsLspTimeUp OBJECT-TYPE
+    SYNTAX     TimeStamp
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+        "The total time in 10-millisecond units that this
+         LSP has been operational. The percentage up time
+         can be determined by computing
+         (mplsLspTimeUp/mplsLspAge * 100 %)."
+    ::= { mplsLspEntry 7 }
+
+mplsLspPrimaryTimeUp OBJECT-TYPE
+    SYNTAX     TimeStamp
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+        "The total time in 10-millisecond units that this
+         LSP's primary path has been operational. The
+         percentage contribution of the primary
+         path to the operational time is given by
+         (mplsLspPrimaryTimeUp/mplsLspTimeUp * 100) %."
+    ::= { mplsLspEntry 8 }
+
+mplsLspTransitions OBJECT-TYPE
+    SYNTAX     Counter32
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+        "The number of state transitions (up -> down and
+         down -> up) this LSP has undergone."
+    ::= { mplsLspEntry 9 }
+
+mplsLspLastTransition OBJECT-TYPE
+    SYNTAX     TimeStamp
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+        "The time in 10-millisecond units since the last
+         transition occurred on this LSP."
+    ::= { mplsLspEntry 10 }
+
+mplsLspFrom OBJECT-TYPE
+    SYNTAX     IpAddress
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+        "Source IP address of this LSP."
+    ::= { mplsLspEntry 11 }
+
+mplsLspTo OBJECT-TYPE
+    SYNTAX     IpAddress
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+        "Destination IP address of this LSP."
+    ::= { mplsLspEntry 12 }
+
+mplsLspPathName OBJECT-TYPE
+    SYNTAX     DisplayString (SIZE(0..16))
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+        "The name of the active path for this LSP, if
+         any.  If there is none, the name should be
+         empty; in that case, the rest of the fields
+         in mplsLspEntry are meaningless."
+    ::= { mplsLspEntry 13 }
+
+mplsLspPathType OBJECT-TYPE
+    SYNTAX     INTEGER {
+        other(1),
+        primary(2),
+        standby(3),
+        secondary(4)
+    }
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+        "The type of path that is active, i.e., a
+         primary path, a standby path, or a generic
+         secondary path. This field is meaningless
+         unless mplsLspPathName is not empty"
+    ::= { mplsLspEntry 14 }
+
+mplsLspAdaptive OBJECT-TYPE
+    SYNTAX          TruthValue
+    MAX-ACCESS read-only
+    STATUS          current
+    DESCRIPTION
+        "Indicates if the LSP supports adaptive mechanism or not."
+    ::= { mplsLspEntry 15 }
+
+mplsLspBfdSessionId OBJECT-TYPE
+    SYNTAX          Unsigned32
+    MAX-ACCESS read-only
+    STATUS          current
+    DESCRIPTION
+        "The BFD session ID associated to this LSP. Zero indicates
+         there is no BFD session for this LSP. Non-zero value is an
+         index to an entry in the bfdSessTable"
+    ::= { mplsLspEntry 16 }
+
+ mplsLspReoptimizeTimer OBJECT-TYPE
+    SYNTAX          Unsigned32 ( 0 | 300..65535 )
+    MAX-ACCESS read-only
+    STATUS          current
+    DESCRIPTION
+        "The number of seconds from the beginning of one reoptimization
+         attempt to the beginning of the next attempt."
+    ::= { mplsLspEntry 17 }
+
+mplsLspCoS OBJECT-TYPE
+    SYNTAX          ClassOfService
+    MAX-ACCESS read-only
+    STATUS          current
+    DESCRIPTION
+        "The Class of Service for this LSP."
+    ::= { mplsLspEntry 18 }
+
+mplsLspHopLimit OBJECT-TYPE
+    SYNTAX          Unsigned32 ( 0..255 )
+    MAX-ACCESS read-only
+    STATUS          current
+    DESCRIPTION
+        "The number of hops this LSP can traverse."
+    ::= { mplsLspEntry 19 }
+
+mplsLspCspf OBJECT-TYPE
+    SYNTAX          INTEGER {
+               enabled(1),
+               disabled(2)
+    }
+    MAX-ACCESS read-only
+    STATUS          current
+    DESCRIPTION
+        "Indicates if CSPF path calculation is enabled
+         on this LSP."
+    ::= { mplsLspEntry 20 }
+
+mplsLspCspfTieBreaker OBJECT-TYPE
+    SYNTAX          INTEGER {
+               random(1),
+               leastFill(2),
+               mostFill(3)
+    }
+    MAX-ACCESS read-only
+    STATUS          current
+    DESCRIPTION
+        "The tie-breaker to use for selecting CSPF
+         equal-cost paths. The value of this variable is
+         meaningless if the mplsLspCspf is 'disabled'."
+    ::= { mplsLspEntry 21 }
+
+mplsLspFrrMode OBJECT-TYPE
+    SYNTAX          INTEGER {
+               none(1),
+               detour(2),
+               facility(3)
+    }
+    MAX-ACCESS read-only
+    STATUS          current
+    DESCRIPTION
+        "Indicates which protection method is to be used
+         for Fast Reroute. 'detour' means one-to-one backup
+         and 'facility' for facility backup."
+    ::= { mplsLspEntry 22 }
+
+mplsLspFrrSetupPriority OBJECT-TYPE
+    SYNTAX          Unsigned32 (0..7)
+    MAX-ACCESS read-only
+    STATUS          current
+    DESCRIPTION
+        "The setup priority for MPLS Fast Reroute.
+         The value of this variable is meaningless if the
+         mplsLspFrrMode is 'none'."
+    ::= { mplsLspEntry 23 }
+
+mplsLspFrrHoldingPriority OBJECT-TYPE
+    SYNTAX          Unsigned32 (0..7)
+    MAX-ACCESS read-only
+    STATUS          current
+    DESCRIPTION
+        "The hold priority for MPLS Fast Reroute.
+         The value of this variable is meaningless if the
+         mplsLspFrrMode is 'none'."
+    ::= { mplsLspEntry 24 }
+
+mplsLspFrrHopLimit OBJECT-TYPE
+    SYNTAX          Unsigned32 ( 0..255 )
+    MAX-ACCESS read-only
+    STATUS          current
+    DESCRIPTION
+        "The hop limit for MPLS Fast Reroute.
+         The value of this variable is meaningless if the
+         mplsLspFrrMode is 'none'."
+    ::= { mplsLspEntry 25 }
+
+mplsLspFrrBandwidth OBJECT-TYPE
+    SYNTAX          Unsigned32 (0..2147483647)
+    MAX-ACCESS read-only
+    STATUS          current
+    DESCRIPTION
+        "The bandwidth constraint for MPLS Fast Reroute.
+         The value 0 means that the detour route uses a
+         best-effort value for bandwidth.
+         The value of this variable is meaningless if the
+         mplsLspFrrMode is 'none'."
+    ::= { mplsLspEntry 26 }
+
+mplsLspFrrAdmGrpIncludeAny OBJECT-TYPE
+    SYNTAX          MplsTunnelAffinity
+    MAX-ACCESS read-only
+    STATUS          current
+    DESCRIPTION
+        "The administrative group setting that the device
+         includes any of the interfaces that are members of
+         the group when calculating detour routes for this LSP.
+         The value of this variable is meaningless if the
+         mplsLspFrrMode is 'none'."
+    ::= { mplsLspEntry 27 }
+
+mplsLspFrrAdmGrpIncludeAll OBJECT-TYPE
+    SYNTAX          MplsTunnelAffinity
+    MAX-ACCESS read-only
+    STATUS          current
+    DESCRIPTION
+        "The administrative group setting that an interface
+         must be a member of to be considered in a detour
+         route for the LSP. Any interface that is not a member
+         of all the groups is eliminated from consideration.
+         The value of this variable is meaningless if the
+         mplsLspFrrMode is 'none'."
+    ::= { mplsLspEntry 28 }
+
+mplsLspFrrAdmGrpExcludeAny OBJECT-TYPE
+    SYNTAX          MplsTunnelAffinity
+    MAX-ACCESS read-only
+    STATUS          current
+    DESCRIPTION
+        "The administrative group setting that the device
+         excludes any of the interfaces that are members of
+         the group when calculating detour routes for this LSP.
+         The value of this variable is meaningless if the
+         mplsLspFrrMode is 'none'."
+    ::= { mplsLspEntry 29 }
+
+mplsLspPathSelectMode OBJECT-TYPE
+    SYNTAX          INTEGER {
+               auto(1),
+               manual(2),
+               unconditional(3)
+    }
+    MAX-ACCESS read-only
+    STATUS          current
+    DESCRIPTION
+        "Indicates the path selection mode to use.
+         Auto-select is the default mode. I this mode, the
+         primary path is always selected to carry traffic when
+         the primary path has stayed operating in the working
+         state for at least the amount of time specified in
+         mplsLspPathSelectRevertTimer.
+         For manual-select, traffic is switched to a user-
+         selected path specified in mplsLspPathSelectPathname
+         after the selected path has stayed operating in the
+         working state for at least the amount of time specified
+         in mplsLspPathSelectRevertTimer.
+         For unconditional-select, traffic is switched to and
+         stays on the selected path regardless of the path's
+         condition even if it is in a failure state."
+    ::= { mplsLspEntry 30 }
+
+mplsLspPathSelectPathname OBJECT-TYPE
+    SYNTAX     DisplayString (SIZE (0..64))
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+        "The user-selected pathname when the mplsLspPathSelectMode
+         is either 'manual' or 'unconditional'."
+    ::= { mplsLspEntry 31 }
+
+mplsLspPathSelectRevertTimer OBJECT-TYPE
+    SYNTAX          Unsigned32 (0..65535)
+    MAX-ACCESS read-only
+    STATUS          current
+    DESCRIPTION
+        "The number of seconds to wait after the primary or selected
+         path comes up before traffic reverts to that path.
+         A value of 0 indicates that it will switch immediately
+         after the current working path goes down."
+    ::= { mplsLspEntry 32 }
+
+mplsLspShortcutOspfAllowed OBJECT-TYPE
+    SYNTAX          TruthValue
+    MAX-ACCESS read-only
+    STATUS          current
+    DESCRIPTION
+        "Indicates that this LSP allows shortcut between nodes in an AS.
+         OSPF includes the LSP in its SPF calculation."
+    ::= { mplsLspEntry 33 }
+
+mplsLspShortcutIsisAllowed OBJECT-TYPE
+    SYNTAX          TruthValue
+    MAX-ACCESS read-only
+    STATUS          current
+    DESCRIPTION
+        "Indicates that this LSP allows shortcut through the
+         network to a destination based on the path's cost (metric).
+         Traffic is forwarded through this LSP to destinations
+         within the IS-IS routing domain. IS-IS includes the LSP
+         in its SPF calculation."
+    ::= { mplsLspEntry 34 }
+
+mplsLspShortcutIsisLevel OBJECT-TYPE
+    SYNTAX          INTEGER {
+               level1(1),
+               level2(2),
+               level1and2(3)
+    }
+    MAX-ACCESS read-only
+    STATUS          current
+    DESCRIPTION
+        "Indicates the level of IS-IS routing enabled on the device.
+         The value of this variable is meaningless if the
+         mplsLspShortcutIsisAllowed is 'false'."
+    ::= { mplsLspEntry 35 }
+
+mplsLspShortcutIsisAnnounce OBJECT-TYPE
+    SYNTAX          TruthValue
+    MAX-ACCESS read-only
+    STATUS          current
+    DESCRIPTION
+        "Indicates that this IS-IS shortcut will be announced or
+         advertised. The metric to announce is specified by
+         mplsLspShortcutIsisAnnounceMetric.
+         The value of this variable is meaningless if the
+         mplsLspShortcutIsisAllowed is 'false'."
+    ::= { mplsLspEntry 36 }
+
+mplsLspShortcutIsisAnnounceMetric OBJECT-TYPE
+    SYNTAX          Integer32 (1..16777215)
+    MAX-ACCESS read-only
+    STATUS          current
+    DESCRIPTION
+        "Indicates the metric value to announce for this shortcut.
+         The value of this variable is meaningless if the
+         mplsLspShortcutIsisAnnounce is 'false'. Default value is 10."
+    ::= { mplsLspEntry 37 }
+
+mplsLspShortcutIsisRelativeMetric OBJECT-TYPE
+    SYNTAX          Integer32 (-16777215..16777215)
+    MAX-ACCESS read-only
+    STATUS          current
+    DESCRIPTION
+        "Indicates the relative metric used to compute the LSP cost
+         when announce is not enabled.
+         The value of this variable is meaningless if the
+         mplsLspShortcutIsisAllowed is 'false'."
+    ::= { mplsLspEntry 38 }
+
+
+-- definition of MPLS traps
+--
+snMplsLspUp NOTIFICATION-TYPE
+OBJECTS { mplsLspName,
+          mplsLspPathName } -- LspPath
+STATUS current
+DESCRIPTION
+     "An mplsLspUp trap signifies that the
+     specified LSP is up. The current active
+     path for the LSP is mplsLspPathName."
+--#TYPE "Foundry Trap: MPLS LSP Up"
+--#SUMMARY "LSP %s using path %s is up."
+--#ARGUMENTS { 0, 1 }
+--#SEVERITY INFORMATIONAL
+--#STATE OPERATIONAL
+::= { snTraps 1010 }
+
+
+snMplsLspDown NOTIFICATION-TYPE
+OBJECTS { mplsLspName,
+          mplsLspPathName } -- LspPath
+STATUS current
+DESCRIPTION
+     "An mplsLspDown trap signifies that the
+     specified LSP is down, because the current
+     active path mplsLspPathName went down."
+--#TYPE "Foundry Trap: MPLS LSP Down"
+--#SUMMARY "LSP %s using path %s is down."
+--#ARGUMENTS { 0, 1 }
+--#SEVERITY INFORMATIONAL
+--#STATE OPERATIONAL
+::= { snTraps 1011 }
+
+
+snMplsLspChange NOTIFICATION-TYPE
+OBJECTS { mplsLspName,
+          mplsLspPathName } -- LspPath
+STATUS current
+DESCRIPTION
+     "An mplsLspChange trap signifies that the
+     the specified LSP has switched traffic to
+     the new active path 'toLspPath'. The LSP maintains
+     up state before and after the switch over"
+--#TYPE "Foundry Trap: MPLS LSP Change"
+--#SUMMARY "LSP %s switches to new active path %s."
+--#ARGUMENTS { 0, 1 }
+--#SEVERITY INFORMATIONAL
+--#STATE OPERATIONAL
+::= { snTraps 1012 }
+
+END

mibs/IANA-PWE3-MIB

@@ -0,0 +1,115 @@
+   IANA-PWE3-MIB DEFINITIONS ::= BEGIN
+
+   IMPORTS
+       MODULE-IDENTITY
+          FROM SNMPv2-SMI -- [RFC2578]
+       pwe3
+          FROM FOUNDRY-SN-ROOT-MIB
+       TEXTUAL-CONVENTION
+          FROM SNMPv2-TC; -- [RFC2579]
+
+   ianaPwe3MIB  MODULE-IDENTITY
+       LAST-UPDATED "200702041200Z"  -- 4 February 2006 12:00:00 GMT
+       ORGANIZATION "IANA"
+       CONTACT-INFO
+            "Internet Assigned Numbers Authority
+            Internet Corporation for Assigned Names and Numbers
+            4676 Admiralty Way, Suite 330
+            Marina del Rey, CA 90292-6601
+
+            Phone: +1 310 823 9358
+            EMail: iana@iana.org"
+       DESCRIPTION
+           "This MIB module defines the IANAPwTypeTC and
+           IANAPwPsnTypeTC textual conventions for use in PWE3
+           MIB modules.
+
+           Any additions or changes to the contents of this MIB
+           module require either publication of an RFC, Designated
+           Expert Review as defined in RFC 2434, Guidelines for
+           Writing an IANA Considerations Section in RFCs, and should
+           be based on the procedures defined in [RFC4446]. The
+           Designated Expert will be selected by the IESG Area
+           Director(s) of the internet Area.
+
+           Copyright (C) The IETF Trust (2007).  The initial
+           version of this MIB module was published in RFC yyyy;
+           for full legal notices see the RFC itself.  Supplementary
+           information may be available at:
+           http://www.ietf.org/copyrights/ianamib.html."
+      -- RFC Ed.: replace yyyy with actual RFC number & remove this note
+
+       REVISION     "200702041200Z"  -- 4 February 2006 12:00:00 GMT
+       DESCRIPTION  "Original version, published as part of RFC yyyy."
+   -- RFC Editor: please fill the yyyy and remove this note.
+
+       ::= { pwe3 3 }
+       -- ::= { transmission XXXX }
+   -- RFC Editor: please fill the XXXX based on the IANA allocation
+   -- and remove this note.
+
+   IANAPwTypeTC ::= TEXTUAL-CONVENTION
+      STATUS     current
+      DESCRIPTION
+         "Indicates the PW type (i.e. the carried service). "
+    SYNTAX   INTEGER {
+       other(0),
+       frameRelayDlciMartiniMode(1),
+       atmAal5SduVcc(2),
+       atmTransparent(3),
+       ethernetTagged(4),
+       ethernet(5),
+       hdlc(6),
+       ppp(7),
+       cem(8),  -- Historic type
+       atmCellNto1Vcc(9),
+       atmCellNto1Vpc(10),
+       ipLayer2Transport(11),
+       atmCell1to1Vcc(12),
+       atmCell1to1Vpc(13),
+       atmAal5PduVcc(14),
+       frameRelayPortMode(15),
+       cep(16),
+       e1Satop(17),
+       t1Satop(18),
+       e3Satop(19),
+       t3Satop(20),
+       basicCesPsn(21),
+       basicTdmIp(22),
+       tdmCasCesPsn(23),
+       tdmCasTdmIp(24),
+       frDlci(25),
+       wildcard (32767)
+        }
+
+   IANAPwPsnTypeTC ::= TEXTUAL-CONVENTION
+      STATUS      current
+      DESCRIPTION
+         "Identifies the PSN type which the PW will use over the
+          network."
+      SYNTAX   INTEGER {
+         mpls        (1),
+         l2tp        (2),
+         udpOverIp   (3),
+         mplsOverIp  (4),
+         mplsOverGre (5),
+         other       (6)
+         }
+
+   IANAPwCapabilities ::= TEXTUAL-CONVENTION
+      STATUS      current
+      DESCRIPTION
+         "This TC describes a collection of cabailities related to
+          a specific PW.
+          Values may be added in the future based on new capabilities
+          introduced in IETF documents.
+         "
+     SYNTAX   BITS {
+       pwStatusIndication (0), -- Applicable only if maintenence
+                               -- protocol is in use.
+       pwVCCV             (1)
+     }
+
+   END
+
+

mibs/PW-ENET-STD-MIB

@@ -0,0 +1,480 @@
+PW-ENET-STD-MIB DEFINITIONS ::= BEGIN
+
+IMPORTS
+   OBJECT-TYPE, MODULE-IDENTITY, Unsigned32
+       FROM SNMPv2-SMI                    -- [RFC2578]
+
+   pwe3
+       FROM FOUNDRY-SN-ROOT-MIB
+
+   MODULE-COMPLIANCE, OBJECT-GROUP
+       FROM SNMPv2-CONF                   -- [RFC2580]
+
+   StorageType, RowStatus
+       FROM SNMPv2-TC                     -- [RFC2579]
+
+   InterfaceIndexOrZero
+       FROM IF-MIB                        -- [RFC2863]
+
+   ZeroBasedCounter32
+       FROM RMON2-MIB                     -- [RFC4502]
+
+   pwIndex
+       FROM PW-STD-MIB                    -- [PWMIB]
+                                 -- RFC Editor: Please replace
+                                 -- PWMIB with correct RFC #
+
+   PwVlanCfg
+       FROM PW-TC-STD-MIB;                -- [PWTC]
+                              -- RFC Editor: Please replace
+                              -- PWTC with correct RFC #
+
+pwEnetStdMIB MODULE-IDENTITY
+    LAST-UPDATED "200705201200Z"  -- 20 May 2007 12:00:00 GMT
+    ORGANIZATION "IETF PWE3 Working group"
+    CONTACT-INFO
+         "David Zelig
+          E-mail: davidz@corrigent.com
+
+          Thomas D. Nadeau
+          Email:  tnadeau@cisco.com
+        "
+    DESCRIPTION
+        "This MIB module describes a model for managing Ethernet
+        point-to-point pseudo-wire services over a Packet
+        Switched Network (PSN).
+
+        Copyright (C) The IETF Trust (2007).  This version
+        of this MIB module is part of RFC yyyy;  see the RFC
+        itself for full legal notices.
+-- RFC Editor: replace yyyy with the actual RFC number and remove
+-- this note
+        "
+
+   -- Revision history.
+   REVISION "200705201200Z"  -- 20 May 2007 12:00:00 GMT
+   DESCRIPTION "Initial version published as part of RFC XXXX."
+-- RFC Editor: Please replace XXXX with the actual RFC number and
+-- remove this note
+
+
+      ::= { pwe3 4 }
+      -- ::= { transmission XXXX }
+                          -- RFC Editor: Please replace
+                          -- XXXX with IANA assigned value.
+                          -- See IANA considerations section.
+
+pwEnetObjects        OBJECT IDENTIFIER ::= { pwEnetStdMIB 1 }
+pwEnetConformance    OBJECT IDENTIFIER ::= { pwEnetStdMIB 2 }
+
+--
+-- Ethernet PW table
+--
+
+pwEnetTable  OBJECT-TYPE
+    SYNTAX SEQUENCE OF PwEnetEntry
+    MAX-ACCESS  not-accessible
+    STATUS     current
+    DESCRIPTION
+        "This table contains the index to the Ethernet tables
+        associated with this ETH PW, the VLAN configuration and
+        VLAN mode."
+    ::= { pwEnetObjects 1 }
+
+pwEnetEntry  OBJECT-TYPE
+    SYNTAX     PwEnetEntry
+    MAX-ACCESS  not-accessible
+    STATUS     current
+    DESCRIPTION
+        "This table is indexed by the same index that was created
+        for the associated entry in the PW generic table in the
+        PW-STD-MIB module.
+        The pwIndex and the pwEnetPwInstance are used as indexes
+        to allow multiple VLANs to exist on the same PW.
+
+        An entry is created in this table by the agent for every
+        entry in the pwTable with a pwType of 'ethernetTagged'
+        or 'ethernet'. Additional rows may be created by the
+        operator or the agent if multiple entries are required for
+        the same PW.
+
+        The value of pwEnetPwInstance can be arbitrary selected
+        to make the row unique, however implementations that know
+        the VLAN field value when the row is created MAY use the
+        value of the VLAN itself for better readability and
+        backward compatibility with older versions of this MIB
+        module.
+
+        This table provides Ethernet port mapping and VLAN
+        configuration for each Ethernet PW.
+
+        All read-create object in this table MAY be changed at any
+        time, however change of some objects (for example
+        pwEnetVlanMode) during PW forwarding state MAY cause traffic
+        disruption.
+
+        Manual entries in this table SHOULD be preserved after a
+        re-boot, the agent MUST ensure the integrity of those
+        entries. If the set of entires of a specific row are found to
+        be non consistent after reboot, the PW pwOperStatus MUST be
+        declared as notPresent(5).
+        "
+
+    INDEX { pwIndex, pwEnetPwInstance }
+    ::= { pwEnetTable 1 }
+
+
+PwEnetEntry ::= SEQUENCE {
+       pwEnetPwInstance    Unsigned32,
+       pwEnetPwVlan        PwVlanCfg,
+       pwEnetVlanMode      INTEGER,
+       pwEnetPortVlan      PwVlanCfg,
+
+       pwEnetPortIfIndex   InterfaceIndexOrZero,
+       pwEnetPwIfIndex     InterfaceIndexOrZero,
+
+       pwEnetRowStatus     RowStatus,
+       pwEnetStorageType   StorageType
+   }
+
+pwEnetPwInstance  OBJECT-TYPE
+    SYNTAX      Unsigned32
+    MAX-ACCESS  not-accessible
+    STATUS      current
+    DESCRIPTION
+        "If multiple rows are mapped to the same PW, this index is
+         used to uniquely identify the individual row.
+         If the value of the VLAN field is known at the time of
+         of row creation, the value of pwEnetPwVlan MAY be used
+         for better readability and backward compatibility with
+         older versions of this MIB module. Otherwise the value
+         '1' SHOULD be set to the first row for each pwIndex
+         for better readability and in order that the management
+         application will know in advance how to access the
+         first row when it was created by the agent.
+        "
+    ::= { pwEnetEntry 1 }
+
+pwEnetPwVlan  OBJECT-TYPE
+    SYNTAX      PwVlanCfg
+    MAX-ACCESS  read-create
+    STATUS      current
+    DESCRIPTION
+        "This Object defines the (service delimiting) VLAN field
+        value on the PW. The value of 4097 MUST be used if the
+        object is not applicable, for example when mapping all
+        packets from an Ethernet port to this PW (raw mode).
+        The value 4096 MUST be set to indicate untagged frames
+        (from the PW point of view), i.e. when pwEnetVlanMode
+        equals 'noChange' and pwEnetPortVlan equals 4096."
+    ::= { pwEnetEntry 2 }
+
+pwEnetVlanMode  OBJECT-TYPE
+    SYNTAX     INTEGER {
+             other(0),
+             portBased(1),
+             noChange(2),
+             changeVlan(3),
+             addVlan(4),
+             removeVlan(5)
+    }
+    MAX-ACCESS  read-create
+    STATUS     current
+    DESCRIPTION
+        "This object indicates the mode of VLAN handling between the
+         port or the virtual port associated with the PW and the
+         PW encapsulation.
+
+        - 'other' indicates an operation that is not defined by
+          this MIB module.
+
+        - 'portBased' indicates that the forwarder will forward
+          packets between the port and the PW independent of their
+          structure (i.e. there is no service delimiting VLAN tags
+          from the PE standpoint).
+
+        - 'noChange' indicates that the PW contains the original
+           user VLAN, as specified in pwEnetPortVlan, i.e. the
+           VLAN on the PE-CE link is the service delimiting tag
+           and is kept 'as is' on the PW.
+
+        - 'changeVlan' indicates that the VLAN field on the PW
+          may be different than the VLAN field on the user's
+          port. The VLAN on the PE-CE link is the service delimiting
+          tag but has a different value on the PW.
+
+        - 'removeVlan' indicates that the encapsulation on the
+          PW does not include the service delimiting VLAN field.
+          Note that PRI bits transparency is lost in this case.
+
+        - 'addVlan' indicates that a VLAN field will be added
+          on the PSN bound direction (i.e. on the PW). pwEnetPwVlan
+          indicates the value that will be added.
+
+        - Implementation of 'portsbased', 'removeVlan', 'addVlan'
+          'other' and 'changeVlan' is OPTIONAL.
+        "
+    DEFVAL { noChange }
+    ::= { pwEnetEntry 3 }
+
+pwEnetPortVlan  OBJECT-TYPE
+    SYNTAX     PwVlanCfg
+    MAX-ACCESS read-create
+    STATUS     current
+    DESCRIPTION
+        "This object defines if the mapping between the original port
+        (physical port or VPLS virtual port) to the PW is VLAN based
+        or not. In case of VLAN mapping, this object indicates the
+        the VLAN value on the original port.
+
+        The value of '4097' MUST be used if the whole original port
+        traffic is mapped to the same PW. Note that a pwType of
+        'ethernetTagged' can still be used if service delimiting tag
+        is added on the PW (pwEnetVlanMode equals 'addVlan').
+
+        This object MUST be equal to pwEnetPwVlan if pwEnetVlanMode
+        equals 'noChange'.
+
+        The value 4096 indicates packets without VLAN field
+        (i.e. untagged frames) on the port are associated to this
+        PW. This allows the same behavior as assigning 'Default
+        VLAN' to untagged frames.
+        "
+    DEFVAL  { 4097 }
+    ::= { pwEnetEntry 4 }
+
+pwEnetPortIfIndex  OBJECT-TYPE
+    SYNTAX      InterfaceIndexOrZero
+    MAX-ACCESS  read-create
+    STATUS      current
+    DESCRIPTION
+        "This object is used to specify the ifIndex of the Ethernet
+         port associated with this PW for point-to-point Ethernet
+         service, or the ifIndex of the virtual interface of the
+         VPLS instance associated with the PW if the service is
+         VPLS. Two rows in this table can point to the same ifIndex
+         only if there is no overlap of VLAN values specified in
+         pwEnetPortVlan that are associated with this port.
+
+         A value of zero indicates that association to an ifIndex is
+         not yet known."
+
+    ::= { pwEnetEntry 5 }
+
+pwEnetPwIfIndex  OBJECT-TYPE
+    SYNTAX     InterfaceIndexOrZero
+    MAX-ACCESS read-create
+    STATUS     current
+    DESCRIPTION
+        "If the PW is modeled as an ifIndex in the ifTable, this
+         object indicates the value of the ifIndex representing the
+         Ethernet PW on the PSN side in the Etherlike-MIB. Note that
+         this value may be different from the value of pwIfIndex
+         that represents the ifIndex of the PW for ifType 'pw'."
+
+     DEFVAL { 0 }
+    ::= { pwEnetEntry 6 }
+
+pwEnetRowStatus  OBJECT-TYPE
+    SYNTAX      RowStatus
+    MAX-ACCESS  read-create
+    STATUS      current
+    DESCRIPTION
+        "This object enables creating, deleting and modifying this row."
+    ::= { pwEnetEntry 7 }
+
+pwEnetStorageType  OBJECT-TYPE
+    SYNTAX      StorageType
+    MAX-ACCESS  read-create
+    STATUS      current
+    DESCRIPTION
+        "This object indicates the storage type of this row."
+    DEFVAL { nonVolatile }
+    ::= { pwEnetEntry 8 }
+
+--
+-- Ethernet PW Statistics Table
+--
+
+pwEnetStatsTable  OBJECT-TYPE
+    SYNTAX SEQUENCE OF PwEnetStatsEntry
+    MAX-ACCESS  not-accessible
+    STATUS      current
+    DESCRIPTION
+        "This table contains statistical counters specific for
+         Ethernet PW."
+    ::= { pwEnetObjects 2 }
+
+pwEnetStatsEntry  OBJECT-TYPE
+    SYNTAX      PwEnetStatsEntry
+    MAX-ACCESS  not-accessible
+    STATUS      current
+    DESCRIPTION
+        "Each entry represents the statistics gathered for the
+         PW carrying the Ethernet."
+    INDEX { pwIndex }
+    ::= { pwEnetStatsTable 1 }
+
+
+PwEnetStatsEntry ::= SEQUENCE {
+    pwEnetStatsIllegalVlan        ZeroBasedCounter32,
+    pwEnetStatsIllegalLength      ZeroBasedCounter32
+}
+
+pwEnetStatsIllegalVlan  OBJECT-TYPE
+    SYNTAX     ZeroBasedCounter32
+    MAX-ACCESS  read-only
+    STATUS     current
+    DESCRIPTION
+        "The number of packets received (from the PSN) on this PW
+         with either an illegal VLAN field, a missing VLAN field
+         when one was expected, or an excessive VLAN field when
+         it was not expected. This counter may not be applicable
+         in some cases, and MUST return the value of zero in
+         such a case."
+    ::= { pwEnetStatsEntry 1 }
+
+pwEnetStatsIllegalLength  OBJECT-TYPE
+    SYNTAX     ZeroBasedCounter32
+    MAX-ACCESS  read-only
+    STATUS     current
+    DESCRIPTION
+        "The number of packets that were received with an illegal
+         Ethernet packet length on this PW. An illegal length is
+         defined as being greater than the value in the advertised
+         MTU supported, or shorter than the allowed Ethernet packet
+         size."
+    ::= { pwEnetStatsEntry 2 }
+
+---
+--- Conformance description
+---
+
+pwEnetGroups      OBJECT IDENTIFIER ::= { pwEnetConformance 1 }
+pwEnetCompliances OBJECT IDENTIFIER ::= { pwEnetConformance 2 }
+
+-- Compliance requirement for fully compliant implementations.
+
+pwEnetModuleFullCompliance MODULE-COMPLIANCE
+    STATUS  current
+    DESCRIPTION
+            "The compliance statement for agents that provide full
+             support for the PW-ENET-STD-MIB Module. Such devices
+             can then be monitored and also be configured using
+             this MIB module."
+    MODULE  -- this module
+      MANDATORY-GROUPS {
+                         pwEnetGroup,
+                         pwEnetStatsGroup
+                        }
+
+   OBJECT       pwEnetVlanMode
+   DESCRIPTION "An implementation MUST support at least the value
+                noChange(2)."
+
+   OBJECT       pwEnetPwIfIndex
+   MIN-ACCESS   read-only
+   DESCRIPTION "Write access and values other than zero are
+                required only for implementations that support
+                modeling the Ethernet PW in the Etherlike-MIB."
+
+   OBJECT       pwEnetRowStatus
+   SYNTAX       INTEGER { active(1), notInService(2),
+                            notReady(3) }
+   WRITE-SYNTAX INTEGER { active(1), notInService(2),
+                            createAndGo(4), destroy(6)
+                          }
+   MIN-ACCESS   read-only
+   DESCRIPTION "Support for createAndWait is not required. Support
+                of notReady is not required for implementations that
+                do not support signaling.
+                Support of read-write is not required for
+                implementations that do not support more than one
+                VLAN mapping to the same PW."
+
+    ::= { pwEnetCompliances 1 }
+
+-- Compliance requirement for read-only compliant implementations.
+
+
+pwEnetModuleReadOnlyCompliance MODULE-COMPLIANCE
+    STATUS  current
+    DESCRIPTION
+            "The compliance statement for agents that provide read-
+             only support for the PW-ENET-STD-MIB Module. Such
+             devices can then be monitored but cannot be configured
+             using this MIB module."
+
+    MODULE  -- this module
+      MANDATORY-GROUPS { pwEnetGroup,
+                         pwEnetStatsGroup
+                         }
+
+   OBJECT       pwEnetPwVlan
+   MIN-ACCESS   read-only
+   DESCRIPTION "Write access is not required."
+
+   OBJECT       pwEnetVlanMode
+   MIN-ACCESS   read-only
+   DESCRIPTION "Write access is not required. An implementation
+                MUST support at least the value noChange(2)."
+
+   OBJECT       pwEnetPortVlan
+   MIN-ACCESS   read-only
+   DESCRIPTION "Write access is not required."
+
+   OBJECT       pwEnetPortIfIndex
+   MIN-ACCESS   read-only
+   DESCRIPTION "Write access is not required."
+
+   OBJECT       pwEnetPwIfIndex
+   MIN-ACCESS   read-only
+   DESCRIPTION "Write access is not required. Values other than
+                zero are required only for implementations that
+                support modeling the Ethernet PW in the
+                Etherlike-MIB."
+
+   OBJECT       pwEnetRowStatus
+   SYNTAX       INTEGER { active(1), notInService(2),
+                            notReady(3) }
+   MIN-ACCESS   read-only
+   DESCRIPTION "Write access is not required. Support
+                of notReady is not required for implementations that
+                do not support signaling."
+
+   OBJECT       pwEnetStorageType
+   MIN-ACCESS   read-only
+   DESCRIPTION "Write access is not required."
+
+    ::= { pwEnetCompliances 2 }
+
+-- Units of conformance.
+
+pwEnetGroup OBJECT-GROUP
+   OBJECTS {
+            pwEnetPwVlan,
+            pwEnetVlanMode,
+            pwEnetPortVlan,
+            pwEnetPortIfIndex,
+            pwEnetPwIfIndex,
+            pwEnetRowStatus,
+            pwEnetStorageType
+   }
+   STATUS  current
+   DESCRIPTION
+       "Collection of objects for basic Ethernet PW configuration."
+   ::= { pwEnetGroups 1 }
+
+pwEnetStatsGroup OBJECT-GROUP
+   OBJECTS {
+            pwEnetStatsIllegalVlan,
+            pwEnetStatsIllegalLength
+   }
+   STATUS  current
+   DESCRIPTION
+       "Collection of objects counting various PW level errors."
+   ::= { pwEnetGroups 2 }
+
+END
+
+

mibs/PW-TC-STD-MIB

@@ -0,0 +1,271 @@
+   PW-TC-STD-MIB DEFINITIONS ::= BEGIN
+
+   IMPORTS
+      MODULE-IDENTITY, Unsigned32
+         FROM SNMPv2-SMI               -- [RFC2578]
+
+     pwe3
+        FROM FOUNDRY-SN-ROOT-MIB
+
+      TEXTUAL-CONVENTION
+         FROM SNMPv2-TC;               -- [RFC2579]
+
+   pwTcStdMIB MODULE-IDENTITY
+      LAST-UPDATED "200705241200Z"  -- 24 May 2007 12:00:00 GMT
+      ORGANIZATION "Pseudo Wire Edge-to-Edge Emulation (PWE3) Working
+                    Group"
+      CONTACT-INFO
+      " Thomas D. Nadeau
+        Email:  tnadeau@cisco.com
+
+        David Zelig
+        Email: davidz@corrigent.com
+
+        Orly Nicklass
+        Email: orly_n@rad.com
+
+        The PWE3 Working Group (email distribution pwe3@ietf.org,
+        http://www.ietf.org/html.charters/pwe3-charter.html)
+       "
+
+      DESCRIPTION
+           "This MIB module defines TEXTUAL CONVENTIONs
+            for concepts used in Pseudo Wire Edge-to-Edge
+            networks.
+
+            Copyright (C) The IETF Trust (2007). The
+            initial version of this MIB module as published
+            in RFC YYYY. For full legal notices see the RFC
+            itself or see:
+            http://www.ietf.org/copyrights/ianamib.html
+
+   -- RFC Editor: Please replace YYYY with the RFC number and remove
+   -- this note.
+               "
+      -- Revision history.
+
+      REVISION "200705241200Z"  -- 24 May 2007 12:00:00 GMT
+      DESCRIPTION
+           "Original Version"
+         ::= { pwe3 1 }
+         --::= { transmission XXXX }
+   -- RFC Editor: please replace XXXX with IANA assigned value and
+   -- delete this note.
+
+   PwGroupID ::= TEXTUAL-CONVENTION
+      DISPLAY-HINT "d"
+      STATUS      current
+      DESCRIPTION
+           "An administrative identification for grouping a
+            set of service-specific pseudo-wire services."
+      SYNTAX  Unsigned32
+
+   PwIDType ::= TEXTUAL-CONVENTION
+      DISPLAY-HINT "d"
+      STATUS      current
+      DESCRIPTION
+           "Pseudo-Wire Identifier. Used to identify the PW
+            (together with some other fields) in the signaling
+            session."
+      SYNTAX  Unsigned32
+
+   PwIndexType ::= TEXTUAL-CONVENTION
+      DISPLAY-HINT "d"
+      STATUS      current
+      DESCRIPTION
+           "Pseudo Wire Index. A unique value, greater than zero,
+           for each locally-defined PW for indexing
+           several MIB tables associated with the particular PW.
+           It is recommended that values are assigned contiguously
+           starting from 1.  The value for each PW MUST remain
+           constant at least from one re-initialization
+           to the next re-initialization."
+      SYNTAX  Unsigned32 (1..4294967295)
+
+   PwIndexOrZeroType ::= TEXTUAL-CONVENTION
+      DISPLAY-HINT "d"
+      STATUS      current
+      DESCRIPTION
+           "This textual convention is an extension of the
+            PwIndexType convention.  The latter defines a greater-
+            than-zero value used to identify a Pseudo Wire
+            in the managed system.  This extension permits the
+            additional value of zero. The zero value is object-specific
+            and MUST therefore be defined as part of the description of
+            any object which uses this syntax.  Examples of the usage of
+            zero might include situations where Pseudo Wire was unknown,
+            or when none or all Pseudo Wires need to be referenced."
+       SYNTAX  Unsigned32 (0..4294967295)
+
+   PwVlanCfg ::= TEXTUAL-CONVENTION
+      DISPLAY-HINT "d"
+      STATUS      current
+      DESCRIPTION
+           "VLAN configuration for Ethernet PW.
+            Values between 0 and 4095 indicate the actual VLAN field
+            value.
+            A value of 4096 indicates that the object refers to
+            untagged frames, i.e. frames without a 802.1Q field.
+            A value of 4097 indicates that the object is not
+            relevant."
+      SYNTAX  Unsigned32 (0..4097)
+
+   PwOperStatusTC ::= TEXTUAL-CONVENTION
+      STATUS      current
+      DESCRIPTION
+        "Indicates the operational status of the PW.
+
+        - up(1):            Ready to pass packets.
+        - down(2):          If PW signaling is not yet finished, or
+                            indications available at the service
+                            level indicate that the PW is not
+                            passing packets.
+        - testing(3):       If AdminStatus at the PW level is set to
+                            test.
+        - dormant(4):       The PW is not in a condition to pass
+                            packets, but is in a 'pending' state,
+                            waiting for some external event.
+        - notPresent(5):    Some component is missing to accomplish
+                            the setup of the PW. It can be configuration
+                            error, incomplete configuration or missing
+                            of H/W component.
+        - lowerLayerDown(6):One or more of the lower-layer interfaces
+                            responsible for running the underlying PSN
+                            is not in OperStatus 'up' state."
+    SYNTAX   INTEGER {
+        up(1),
+        down(2),
+        testing(3),
+        dormant(4),
+        notPresent(5),
+        lowerLayerDown(6)
+        }
+
+   PwAttachmentIdentifierType ::= TEXTUAL-CONVENTION
+      STATUS      current
+      DESCRIPTION
+         "An octet string used in the generalized FEC element for
+          identifying attachment forwarder and groups. A NULL
+          identifier is of zero length.
+         "
+     SYNTAX    OCTET STRING (SIZE (0..255))
+
+   PwCwStatusTC ::= TEXTUAL-CONVENTION
+      STATUS      current
+      DESCRIPTION
+         "Indicates the status of the control word negotiation based
+          on the local configuration and the indications received from
+          the peer node.
+
+          waitingForNextMsg(1) indicates that the node is waiting for
+          another label mapping from the peer.
+
+          sentWrongBitErrorCode(2) indicates that the local node has
+          notified the peer about a mismatch in the C bit.
+
+          rxWithdrawWithWrongBitErrorCode(3) indicates that a withdraw
+          message has been received with the wrong C-bit error code.
+
+          illegalReceivedBit(4) indicates a C-bit configuration with
+          the peer which is not compatible with the PW type.
+
+          cwPresent(5) indicates that the CW is present for this PW:
+          If signaling is used - the C bit is set and agreed between the
+          nodes, and for manualy-configured PW the local configuration
+          requires the use of the CW.
+
+          cwNotPresent(6) indicates that the CW is not present for
+          this PW: If signaling is used - the C bit is reset and agreed
+          between the nodes, and for manualy-configured PW the local
+          configuration requires that the CW not be used.
+
+          notYetKnown(7) indicates that a label mapping has not yet
+          been received from the peer.
+         "
+      REFERENCE
+         "Martini, et al, 'Pseudowire Setup and Maintenance using
+          the Label Distribution Protocol', [RFC4447]."
+
+      SYNTAX    INTEGER {
+                 waitingForNextMsg (1),
+                 sentWrongBitErrorCode (2),
+                 rxWithdrawWithWrongBitErrorCode (3),
+                 illegalReceivedBit (4),
+                 cwPresent (5),
+                 cwNotPresent (6),
+                 notYetKnown(7)
+                 }
+
+   PwStatus ::= TEXTUAL-CONVENTION
+      STATUS      current
+      DESCRIPTION
+         "Indicates the status of the PW and the interfaces affecting
+          this PW. If none of the bits are set, it indicates no faults
+          are reported.
+         "
+      SYNTAX   BITS {
+        pwNotForwarding (0),
+        servicePwRxFault (1),
+        servicePwTxFault (2),
+        psnPwRxFault  (3),
+        psnPwTxFault  (4)
+        }
+
+   PwFragSize ::= TEXTUAL-CONVENTION
+      DISPLAY-HINT "d"
+      STATUS      current
+      DESCRIPTION
+         "If set to a value other than zero, it indicates the desired
+          fragmentation length in bytes. If set to zero,
+          fragmentation is not desired for PSN bound packets.
+         "
+      SYNTAX   Unsigned32
+
+   PwFragStatus ::= TEXTUAL-CONVENTION
+      STATUS      current
+      DESCRIPTION
+         "Indicates the status of the fragmentation process based on
+          local configuration and peer capability.
+
+          noFrag(0) bit indicates that local configuration is for no
+          fragmentation.
+
+          cfgFragGreaterThanPsnMtu(1) bit indicates the local node
+          is set to fragment, but the fragmentation size is greater
+          than the MTU available at the PSN between the nodes.
+          Fragmentation is not done in this case.
+
+          cfgFragButRemoteIncapable(2) bit indicates that the local
+          configuration indicates the desire for fragmentation but
+          the peer is not capable of fragmentation.
+
+          remoteFragCapable(3) bit indicates that the remote node
+          is capable to accept fragmented PDUs.
+
+          fragEnabled(4) bit indicates that fargmenteation will be used
+          on this PW. Fragmentation can be used if the local node was
+          configured for fragmentation, the peer has the cabability
+          to accept fragmented packets, and the CW is in use for this
+          PW."
+
+      REFERENCE
+          "Malis, A. and M. Townsley, 'Pseudowire Emulation Edge-to-
+           Edge (PWE3) Fragmentation and Reassembly', [RFC4623]."
+      SYNTAX   BITS {
+         noFrag (0),
+         cfgFragGreaterThanPsnMtu (1),
+         cfgFragButRemoteIncapable (2),
+         remoteFragCapable (3),
+         fragEnabled (4)
+         }
+
+   PwCfgIndexOrzero ::= TEXTUAL-CONVENTION
+      DISPLAY-HINT "d"
+      STATUS      current
+      DESCRIPTION
+           "Index in any of the relevant configuration tables for
+           supplement information regarding configuration of the
+           specific technology. Value 0 implies no additional
+           configuration information is applicable."
+      SYNTAX  Unsigned32 (0..4294967295)
+   END

mibs/VPLS-GENERIC-DRAFT-01-MIB

@@ -0,0 +1,758 @@
+     VPLS-GENERIC-DRAFT-01-MIB DEFINITIONS ::= BEGIN
+
+      IMPORTS
+      NOTIFICATION-TYPE, MODULE-IDENTITY, OBJECT-TYPE,
+      Unsigned32, Counter32
+         FROM SNMPv2-SMI                    -- RFC2578
+
+      MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP
+         FROM SNMPv2-CONF                   -- RFC2580
+
+      TruthValue, RowStatus, StorageType
+         FROM SNMPv2-TC                     -- RFC2579
+
+      SnmpAdminString
+         FROM SNMP-FRAMEWORK-MIB            -- RFC3411
+
+       PwIndexType
+               FROM PW-TC-STD-MIB
+
+        VPNIdOrZero
+               FROM VPN-TC-STD-MIB           -- RFC4265
+
+        vplsRoot
+               FROM FOUNDRY-SN-ROOT-MIB          --snroot
+;
+
+   vplsGenericDraft01MIB MODULE-IDENTITY
+      LAST-UPDATED "200608301200Z"  -- 30 Aug 2006 12:00:00 GMT
+      ORGANIZATION "Layer 2 Virtual Private Networks (L2VPN)
+                                 Working  Group"
+      CONTACT-INFO
+          "
+           Thomas D. Nadeau
+           Email:  tnadeau@cisco.com
+
+           The L2VPN Working Group (email distribution l2vpn@ietf.org,
+           http://www.ietf.org/html.charters/l2vpn-charter.html)
+           "
+
+      DESCRIPTION
+          "Copyright (C) The IETF Trust (2008). The initial
+           version of this MIB module was published in RFC XXXX.
+   -- RFC Editor: Please replace XXXX with RFC number & remove
+   --                    this note.
+
+           For full legal notices see the RFC itself or see:
+           http://www.ietf.org/copyrights/ianamib.html
+
+           This MIB module contains generic managed object definitions
+           for Virtual Private LAN Services as in [L2VPN-VPLS-LDP] and
+           [L2VPN-VPLS-BGP]
+
+           This MIB module enables the use of any underlying Pseudo Wire
+           network."
+
+      -- Revision history.
+      REVISION
+          "200608301200Z"  -- 30 August 2006 12:00:00 GMT
+      DESCRIPTION
+          "Changes from previous version:
+           1) Moved LDP Specific information to VPLS-LDP-DRAFT-01-MIB
+           2) Created the vplsStatusTable to store status information.
+           3)
+          "
+      REVISION
+          "200606041200Z"  -- 4 June 2006 12:00:00 GMT
+
+
+      DESCRIPTION "Initial version published as part of RFC YYYY."
+   -- RFC Editor: please replace YYYY with IANA assigned value, and
+   -- delete this note.
+
+--         ::= { transmission XXXX }
+         ::= { vplsRoot 1 } -- OID assigned under fdry experimental branch.
+   -- RFC Editor: please replace XXXX with IANA assigne value, and
+   -- delete this note.
+
+   -- Top-level components of this MIB.
+
+   -- Notifications
+   vplsNotifications OBJECT IDENTIFIER
+                                 ::= { vplsGenericDraft01MIB 0 }
+   -- Tables, Scalars
+   vplsObjects       OBJECT IDENTIFIER
+                                 ::= { vplsGenericDraft01MIB 1 }
+   -- Conformance
+   vplsConformance   OBJECT IDENTIFIER
+                                 ::= { vplsGenericDraft01MIB 2 }
+
+   -- PW Virtual Connection Table
+
+   vplsConfigIndexNext OBJECT-TYPE
+      SYNTAX            Unsigned32
+      MAX-ACCESS        read-only
+      STATUS            current
+      DESCRIPTION
+          "This object contains an appropriate value to be used
+           for vplsConfigIndex when creating entries in the
+           vplsConfigTable. The value 0 indicates that no
+           unassigned entries are available.  To obtain the
+           value of vplsConfigIndex for a new entry in the
+           vplsConfigTable, the manager issues a management
+           protocol retrieval operation to obtain the current
+           value of vplsConfigIndex.  After each retrieval
+           operation, the agent should modify the value to
+           reflect the next unassigned index.  After a manager
+           retrieves a value the agent will determine through
+           its local policy when this index value will be made
+           available for reuse."
+      ::= { vplsObjects 1 }
+
+      vplsConfigTable OBJECT-TYPE
+          SYNTAX          SEQUENCE OF VplsConfigEntry
+          MAX-ACCESS      not-accessible
+          STATUS          current
+          DESCRIPTION
+               "This table specifies information for configuring
+                and monitoring Virtual Private Lan Services(VPLS).
+                "
+          ::= { vplsObjects 2 }
+
+      vplsConfigEntry OBJECT-TYPE
+          SYNTAX          VplsConfigEntry
+          MAX-ACCESS      not-accessible
+          STATUS          current
+          DESCRIPTION
+           "A row in this table represents a Virtual Private Lan
+            Service(VPLS) in a packet network. It is indexed by
+            vplsConfigIndex, which uniquely identifies a single VPLS.
+
+            A row is created by the operator or by the agent if a
+            VPLS service is created by non-SNMP application or
+            due to autodiscovery process.
+
+            None of the read-create objects values can be
+            changed when vplsConfigRowStatus is in the active(1)
+            state. Changes are allowed when the vplsConfigRowStatus
+            is in notInService(2) or notReady(3) states only.
+            If the operator need to change one of the values
+            for an active row the vplsConfigRowStatus should be
+            first changed to notInService(2), the objects may
+            be changed now, and later to active(1) in order to
+            re-initiate the signaling process with the new
+            values in effect.
+            "
+          INDEX           { vplsConfigIndex }
+          ::= { vplsConfigTable 1 }
+
+     VplsConfigEntry ::=
+        SEQUENCE {
+         vplsConfigIndex                                Unsigned32,
+         vplsConfigName                                 SnmpAdminString,
+         vplsConfigDescr                                SnmpAdminString,
+         vplsConfigAdminStatus                          INTEGER,
+         vplsConfigMacLearning                          TruthValue,
+         vplsConfigDiscardUnknownDest                   TruthValue,
+         vplsConfigMacAging                             TruthValue,
+         vplsConfigFwdFullHighWatermark                 Unsigned32,
+         vplsConfigFwdFullLowWatermark                  Unsigned32,
+         vplsConfigRowStatus                            RowStatus,
+         vplsConfigMtu                                  Unsigned32,
+         vplsConfigVpnId                                VPNIdOrZero,
+         vplsConfigServiceType                          INTEGER,
+         vplsConfigStorageType                          StorageType
+          }
+
+      vplsConfigIndex  OBJECT-TYPE
+          SYNTAX          Unsigned32 (1.. 2147483647)
+
+          MAX-ACCESS      not-accessible
+          STATUS          current
+          DESCRIPTION
+               "Unique index for the conceptual row identifying
+                a VPLS service."
+          ::= { vplsConfigEntry 1 }
+
+      vplsConfigName  OBJECT-TYPE
+          SYNTAX          SnmpAdminString
+          MAX-ACCESS      read-create
+          STATUS          current
+          DESCRIPTION
+               "A textual name of the VPLS.
+                If there is no local name, or this object is
+                otherwise not applicable, then this object MUST
+                contain a zero-length octet string."
+          DEFVAL           { "" }
+          ::= { vplsConfigEntry 2 }
+
+      vplsConfigDescr  OBJECT-TYPE
+          SYNTAX          SnmpAdminString
+          MAX-ACCESS      read-create
+          STATUS          current
+          DESCRIPTION
+               "A textual string containing information about the
+               VPLS service. If there is no information for this VPLS
+               service, then this object MUST contain a zero-length
+               octet string."
+          DEFVAL           { "" }
+          ::= { vplsConfigEntry 3 }
+
+      vplsConfigAdminStatus OBJECT-TYPE
+          SYNTAX          INTEGER {
+                              up(1),
+                              down(2),
+                              testing(3)   -- in some test mode
+
+                          }
+          MAX-ACCESS      read-create
+          STATUS          current
+          DESCRIPTION
+               "The desired administrative state of the VPLS
+                service. If the administrative status of the
+                Vpls service is changed to enable then this
+                service is able to utilize the pseudo wire to
+                perform the tasks of a VPLS service.
+                The testing(3) state indicates that no operational
+                packets can be passed. "
+
+
+          DEFVAL           { down }
+          ::= { vplsConfigEntry 4 }
+
+      vplsConfigMacLearning OBJECT-TYPE
+          SYNTAX          TruthValue
+          MAX-ACCESS      read-create
+          STATUS          current
+          DESCRIPTION
+               "This object specifies if MAC Learning is enabled
+                in this service. If this object is true then Mac
+                Learning is enabled. If false, then Mac Learning is
+                disabled."
+          DEFVAL          { true }
+          ::= { vplsConfigEntry 6 }
+
+      vplsConfigDiscardUnknownDest OBJECT-TYPE
+          SYNTAX          TruthValue
+          MAX-ACCESS      read-create
+          STATUS          current
+          DESCRIPTION
+               "If the value of this object is 'true', then frames
+                received with an unknown destination MAC are discarded
+                in this VPLS. If 'false', then the packets are
+                processed."
+          DEFVAL          { false }
+          ::= { vplsConfigEntry 7 }
+
+      vplsConfigMacAging OBJECT-TYPE
+          SYNTAX          TruthValue
+          MAX-ACCESS      read-create
+          STATUS          current
+          DESCRIPTION
+               "If the value of this object is 'true'
+                then the MAC ageing process is enabled in
+                this VPLS. If 'false', then the MAC ageing process
+                is disabled"
+          DEFVAL          { true }
+          ::= { vplsConfigEntry 8 }
+
+      vplsConfigFwdFullHighWatermark OBJECT-TYPE
+          SYNTAX          Unsigned32 (0..100)
+          UNITS           "percentage"
+          MAX-ACCESS      read-create
+          STATUS          current
+          DESCRIPTION
+
+               "This object specifies the utilization of the
+                forwarding database for this VPLS instance at
+                which the vplsFwdFullAlarmRaised notification
+                will be sent."
+          DEFVAL          { 95 }
+          ::= { vplsConfigEntry 10 }
+
+      vplsConfigFwdFullLowWatermark OBJECT-TYPE
+          SYNTAX          Unsigned32 (0..100)
+          UNITS           "percentage"
+          MAX-ACCESS      read-create
+          STATUS          current
+          DESCRIPTION
+               "This object specifies the utilization of the
+                forwarding database for this VPLS instance
+                at which the vplsFwdFullAlarmCleared
+                notification will be sent."
+          DEFVAL          { 90 }
+          ::= { vplsConfigEntry 11 }
+
+      vplsConfigRowStatus OBJECT-TYPE
+          SYNTAX          RowStatus
+          MAX-ACCESS      read-create
+          STATUS          current
+          DESCRIPTION
+               "For creating, modifying, and deleting this row.
+                None of the read-create objects in the
+                conceptual rows may be changed when this
+                object is in the active(1) state."
+          ::= { vplsConfigEntry 12 }
+
+      vplsConfigMtu OBJECT-TYPE
+          SYNTAX          Unsigned32 (64..1518)
+          MAX-ACCESS      read-create
+          STATUS          current
+          DESCRIPTION
+               "The value of this object specifies the MTU of this
+                vpls instance."
+          DEFVAL          { 1518 }
+          ::= { vplsConfigEntry 13 }
+
+      vplsConfigVpnId OBJECT-TYPE
+          SYNTAX          VPNIdOrZero
+          MAX-ACCESS      read-only
+          STATUS          current
+          DESCRIPTION
+               "This objects indicates the IEEE 802-1990
+                VPN ID of the associated VPLS service."
+-- Ed note: Should we import the VPNIdOrZero TC or
+--              define a new TC?
+          ::= { vplsConfigEntry 14 }
+
+      vplsConfigServiceType OBJECT-TYPE
+          SYNTAX          INTEGER {
+                           vlan     (1),
+                           ethernet (2)
+                          }
+          MAX-ACCESS      read-create
+          STATUS          current
+          DESCRIPTION
+               "The value of this object specifies the type of
+                service emulated by this vpls instance."
+          DEFVAL          { vlan }
+          ::= { vplsConfigEntry 15 }
+
+  vplsConfigStorageType OBJECT-TYPE
+          SYNTAX        StorageType
+          MAX-ACCESS    read-create
+          STATUS        current
+          DESCRIPTION
+               "This variable indicates the storage type for this row."
+          DEFVAL { volatile }
+          ::= { vplsConfigEntry 16 }
+
+-- VPLS Status table
+
+      vplsStatusTable OBJECT-TYPE
+          SYNTAX          SEQUENCE OF VplsStatusEntry
+          MAX-ACCESS      not-accessible
+          STATUS          current
+          DESCRIPTION
+
+
+               "This table provides information for monitoring
+                Virtual Private Lan Services(VPLS).
+                "
+          ::= { vplsObjects 3 }
+
+      vplsStatusEntry OBJECT-TYPE
+          SYNTAX          VplsStatusEntry
+          MAX-ACCESS      not-accessible
+          STATUS          current
+          DESCRIPTION
+           "A row in this table represents a Virtual Private Lan
+            Service(VPLS) in a packet network. It is indexed by
+            vplsConfigIndex, which uniquely identifies a single VPLS.
+
+            A row in this table is automatically created by the agent
+            when a VPLS service is configured.
+            "
+          INDEX           { vplsConfigIndex }
+          ::= { vplsStatusTable 1 }
+
+     VplsStatusEntry ::=
+        SEQUENCE {
+         vplsStatusOperStatus                        INTEGER,
+         vplsStatusPeerCount                         Counter32
+          }
+
+      vplsStatusOperStatus OBJECT-TYPE
+          SYNTAX          INTEGER {
+                              other(0),
+                              up(1),
+                              down(2)
+                          }
+          MAX-ACCESS      read-only
+          STATUS          current
+          DESCRIPTION
+               "The current operational state of this VPLS Service."
+          ::= { vplsStatusEntry 1 }
+
+      vplsStatusPeerCount OBJECT-TYPE
+          SYNTAX          Counter32
+          MAX-ACCESS      read-only
+          STATUS          current
+          DESCRIPTION
+               "This objects specifies the number of peers
+                present in this vpls instance."
+          ::= { vplsStatusEntry 2 }
+
+
+      -- VPLS PW Binding Table
+
+      vplsPwBindTable OBJECT-TYPE
+          SYNTAX          SEQUENCE OF VplsPwBindEntry
+          MAX-ACCESS      not-accessible
+          STATUS          current
+          DESCRIPTION
+               "This table provides an association between a
+                VPLS service and the corresponding Pseudo
+                Wires. A service can have more than one Pseudo
+                Wire association. Pseudo Wires are defined in
+                the pwTable"
+          ::= { vplsObjects 4 }
+
+      vplsPwBindEntry OBJECT-TYPE
+          SYNTAX          VplsPwBindEntry
+          MAX-ACCESS      not-accessible
+          STATUS          current
+          DESCRIPTION
+               "Each row represents an association between a
+                VPLS instance and one or more Pseudo Wires
+                defined in the pwTable. Each index is unique
+                in describing an entry in this table. However
+                both indexes are required to define the one
+                to many association of service to
+                pseudowire."
+          INDEX  { vplsConfigIndex, vplsPwBindIndex }
+          ::= { vplsPwBindTable 1 }
+
+      VplsPwBindEntry ::=
+          SEQUENCE {
+              vplsPwBindIndex                     PwIndexType,
+              vplsPwBindConfigType              INTEGER,
+              vplsPwBindType                  INTEGER,
+              vplsPwBindRowStatus             RowStatus,
+              vplsPwBindStorageType             StorageType
+          }
+
+      vplsPwBindIndex        OBJECT-TYPE
+           SYNTAX        PwIndexType
+           MAX-ACCESS    not-accessible
+           STATUS        current
+           DESCRIPTION
+              "Secondary Index for the conceptual row identifying
+               a pseudowire within the PwEntry which MUST
+               match an entry from the PW-STD-MIB's PwTable
+               which represents an already-provisioned
+               pseuwowire that is then associated with this
+               VPLS instance."
+          ::= { vplsPwBindEntry 1 }
+
+      vplsPwBindConfigType   OBJECT-TYPE
+           SYNTAX          INTEGER {
+                                   manual        (1),
+                                   autodiscovery (2)
+                           }
+           MAX-ACCESS      read-create
+           STATUS          current
+           DESCRIPTION
+                "The value of this object indicates
+                 whether the Pseudo Wire binding was created
+                 manually or via autodiscovery.
+
+                 The value of this object must be
+                 specifed when the row is created and cannot
+                 be changed while the row status is active(1)"
+          ::= { vplsPwBindEntry 2 }
+
+      vplsPwBindType   OBJECT-TYPE
+           SYNTAX          INTEGER {
+                                   mesh  (1),
+                                   spoke (2)
+                           }
+           MAX-ACCESS      read-create
+           STATUS          current
+           DESCRIPTION
+                "The value of this object indicates
+                 whether the Pseudo Wire binding is of
+                 type mesh or spoke.
+
+                 The value of this object must be
+                 specifed when the row is created and cannot
+                 be changed while the row status is active(1)"
+          ::= { vplsPwBindEntry 3 }
+
+      vplsPwBindRowStatus  OBJECT-TYPE
+           SYNTAX          RowStatus
+           MAX-ACCESS      read-create
+           STATUS          current
+           DESCRIPTION
+                "For creating, modifying, and deleting this row.
+                 None of the read-create objects in the
+                 conceptual rows may be changed when this
+                 object is in the active(1) state"
+          ::= { vplsPwBindEntry 4 }
+
+      vplsPwBindStorageType OBJECT-TYPE
+           SYNTAX        StorageType
+           MAX-ACCESS    read-create
+           STATUS        current
+           DESCRIPTION
+                "This variable indicates the storage type for this row."
+           DEFVAL { volatile }
+           ::= { vplsPwBindEntry 5 }
+
+   vplsStatusNotifEnable  OBJECT-TYPE
+      SYNTAX      TruthValue
+      MAX-ACCESS  read-write
+      STATUS      current
+      DESCRIPTION
+           "If this object is set to true(1), then it enables
+            the emission of vplsStatusChanged
+            notification; otherwise this notification is not
+            emitted."
+      REFERENCE
+           "See also [RFC3413] for explanation that
+            notifications are under the ultimate control of the
+            MIB module in this document."
+      DEFVAL { false }
+      ::= { vplsObjects 5 }
+
+   vplsNotificationMaxRate OBJECT-TYPE
+      SYNTAX       Unsigned32
+      MAX-ACCESS   read-write
+      STATUS       current
+      DESCRIPTION
+           "This object indicates the maximum number of
+            notifications issued per second. If events occur
+            more rapidly, the implementation may simply fail to
+            emit these notifications during that period, or may
+            queue them until an appropriate time. A value of 0
+            means no throttling is applied and events may be
+            notified at the rate at which they occur."
+      DEFVAL       { 0 }
+      ::= { vplsObjects 6 }
+
+      -- VPLS Service Notifications
+
+      vplsStatusChanged NOTIFICATION-TYPE
+          OBJECTS {
+              vplsConfigVpnId,
+              vplsConfigAdminStatus,
+              vplsStatusOperStatus
+          }
+          STATUS          current
+          DESCRIPTION
+               "The vplsStatusChanged notification is generated
+                when there is a change in the administrative or
+                operating status of a VPLS service.
+                  This notification is not supported as VPLS instance is always up."
+          --#ENABLE FALSE
+          ::= { vplsNotifications 1 }
+
+      vplsFwdFullAlarmRaised NOTIFICATION-TYPE
+          OBJECTS {
+              vplsConfigVpnId,
+              vplsConfigFwdFullHighWatermark,
+              vplsConfigFwdFullLowWatermark
+          }
+          STATUS          current
+          DESCRIPTION
+               "The vplsFwdFullAlarmRaised notification is
+                generated when the utilization of the Forwarding
+                database is above the value specified by
+                vplsConfigFwdFullHighWatermark.
+                   This notification is not supported by the device."
+          --#ENABLE FALSE
+          ::= { vplsNotifications 2 }
+
+      vplsFwdFullAlarmCleared NOTIFICATION-TYPE
+          OBJECTS {
+              vplsConfigVpnId,
+              vplsConfigFwdFullHighWatermark,
+              vplsConfigFwdFullLowWatermark
+          }
+          STATUS          current
+          DESCRIPTION
+               "The vplsFwdFullAlarmCleared notification is
+                generated when the utilization of the Forwarding
+                database is below the value specified by
+                vplsConfigFwdFullLowWatermark.
+                   This notification is not supported by the device."
+          --#ENABLE FALSE
+          ::= { vplsNotifications 3 }
+
+   -- Compliance requirement for read-only implementations.
+
+   vplsCompliances
+     OBJECT IDENTIFIER ::= { vplsConformance 1 }
+
+   vplsModuleFullCompliance MODULE-COMPLIANCE
+      STATUS current
+      DESCRIPTION
+           "Compliance requirement for implementations that
+            provide full support for VPLS-GENERIC-DRAFT-01-MIB.
+            Such devices can then be monitored and configured using
+            this MIB module."
+      MODULE -- this module
+
+          MANDATORY-GROUPS {
+               vplsGroup,
+               vplsPwBindGroup,
+               vplsNotificationGroup
+           }
+
+      ::= { vplsCompliances 1 }
+
+
+   vplsModuleReadOnlyCompliance MODULE-COMPLIANCE
+      STATUS current
+      DESCRIPTION
+           "Compliance requirement for implementations that only
+            provide read-only support for VPLS-GENERIC-DRAFT-01-MIB.
+            Such devices can then be monitored but cannot be
+            configured using this MIB modules."
+
+      MODULE -- this module
+
+          MANDATORY-GROUPS {
+               vplsGroup,
+               vplsPwBindGroup,
+               vplsNotificationGroup
+           }
+
+           OBJECT          vplsConfigName
+           MIN-ACCESS      read-only
+           DESCRIPTION
+               "Write access is not required."
+
+
+           OBJECT          vplsConfigDescr
+           MIN-ACCESS      read-only
+           DESCRIPTION
+               "Write access is not required."
+
+           OBJECT          vplsConfigAdminStatus
+           MIN-ACCESS      read-only
+           DESCRIPTION
+               "Write access is not required."
+
+           OBJECT          vplsConfigMacLearning
+           MIN-ACCESS      read-only
+           DESCRIPTION
+               "Write access is not required."
+
+           OBJECT          vplsConfigDiscardUnknownDest
+           MIN-ACCESS      read-only
+           DESCRIPTION
+               "Write access is not required."
+
+           OBJECT          vplsConfigMacAging
+           MIN-ACCESS      read-only
+           DESCRIPTION
+               "Write access is not required."
+
+           OBJECT          vplsConfigFwdFullHighWatermark
+           MIN-ACCESS      read-only
+           DESCRIPTION
+               "Write access is not required."
+
+           OBJECT          vplsConfigFwdFullLowWatermark
+           MIN-ACCESS      read-only
+           DESCRIPTION
+               "Write access is not required."
+
+           OBJECT          vplsConfigRowStatus
+           MIN-ACCESS      read-only
+           DESCRIPTION
+               "Write access is not required."
+
+           OBJECT          vplsConfigMtu
+           MIN-ACCESS      read-only
+           DESCRIPTION
+               "Write access is not required."
+
+           OBJECT          vplsConfigServiceType
+           MIN-ACCESS      read-only
+           DESCRIPTION
+               "Write access is not required."
+
+           OBJECT          vplsPwBindConfigType
+           MIN-ACCESS      read-only
+           DESCRIPTION
+               "Write access is not required."
+
+           OBJECT          vplsPwBindType
+           MIN-ACCESS      read-only
+           DESCRIPTION
+               "Write access is not required."
+
+           OBJECT          vplsPwBindRowStatus
+           MIN-ACCESS      read-only
+           DESCRIPTION
+               "Write access is not required."
+
+      ::= { vplsCompliances 2 }
+
+-- Units of conformance.
+
+      vplsGroups
+        OBJECT IDENTIFIER ::= { vplsConformance 2 }
+
+
+      vplsGroup OBJECT-GROUP
+          OBJECTS {
+              vplsConfigName,
+              vplsConfigDescr,
+              vplsConfigAdminStatus,
+              vplsConfigMacLearning,
+              vplsConfigDiscardUnknownDest,
+              vplsConfigMacAging,
+              vplsConfigVpnId,
+              vplsConfigFwdFullHighWatermark,
+              vplsConfigFwdFullLowWatermark,
+              vplsConfigRowStatus,
+              vplsConfigIndexNext,
+              vplsConfigMtu,
+              vplsConfigServiceType,
+              vplsConfigStorageType,
+
+              vplsStatusOperStatus,
+              vplsStatusPeerCount,
+
+              vplsStatusNotifEnable,
+              vplsNotificationMaxRate
+          }
+          STATUS          current
+          DESCRIPTION
+               "The group of objects supporting
+                management of L2VPN VPLS services"
+          ::= { vplsGroups 1 }
+
+      vplsPwBindGroup OBJECT-GROUP
+          OBJECTS {
+              vplsPwBindConfigType,
+              vplsPwBindType,
+              vplsPwBindRowStatus,
+              vplsPwBindStorageType
+          }
+          STATUS          current
+          DESCRIPTION
+               "The group of objects supporting
+                management of
+                Pseudo Wire (PW) Binding to VPLS."
+          ::= { vplsGroups 2 }
+
+      vplsNotificationGroup NOTIFICATION-GROUP
+          NOTIFICATIONS   {
+              vplsStatusChanged,
+              vplsFwdFullAlarmRaised,
+              vplsFwdFullAlarmCleared
+          }
+          STATUS          current
+          DESCRIPTION
+               "The group of notifications supporting
+                the  Notifications generated for
+                VPLS Services"
+          ::= { vplsGroups 3 }
+
+
+       END
+