diff --git a/doc/Support/SNMP-Configuration-Examples.md b/doc/Support/SNMP-Configuration-Examples.md
new file mode 100644
index 0000000000..351116d840
--- /dev/null
+++ b/doc/Support/SNMP-Configuration-Examples.md
@@ -0,0 +1,147 @@
+source: Support/SNMP-Configuration-Examples.md
+
+# SNMP configuration examples
+
+Table of Content:
+- [Devices](#devices)
+    - [Cisco](#cisco)
+        - [Adaptive Security Appliance (ASA)](#adaptive-security-appliance-asa)
+        - [IOS / IOS XE / NX-OS](#ios--ios-xe--nx-os)
+        - [Wireless LAN Controller (WLC)](#wireless-lan-controller-wlc)
+    - [Infoblox](#infoblox)
+        - [NIOS 7.x](#nios-7x)
+    - [Juniper](#juniper)
+        - [Junos OS](#junos-os)
+    - [Palo Alto](#palo-alto)
+        - [PANOS 6.x/7.x](#panos-6x7x)
+- [Operating systems](#operating-systems)
+    - [Linux (snmpd)](#linux-snmpd)
+    - [Windows Server 2008 R2](#windows-server-2008-r2)
+    - [Windows Server 2012 R2](#windows-server-2012-r2)
+
+## Devices
+
+### Cisco
+#### Adaptive Security Appliance (ASA)
+1. Launch ASDM and connect to your device
+2. Go to Configuration > Management Access > SNMP
+3. Add your community string
+4. Add in the "SNMP Host Access List" section your LibreNMS server IP address
+5. Click Apply and Save
+
+#### IOS / IOS XE / NX-OS
+
+``` 
+snmp-server community YOUR-COMMUNITY RO
+snmp-server contact YOUR-CONTACT
+snmp-server location YOUR-LOCATION
+```
+
+#### Wireless LAN Controller (WLC)
+1. Access the web admin page and log in
+2. If you are running version 8.1 and later, on the new dashboard click "Advanced"
+3. Go to management Tab
+4. On SNMP sub-menu, select "Communities"
+5. Click "New..."
+6. Add your community name and leave IP addresses empty
+7. Click Apply and Save
+
+### Infoblox
+#### NIOS 7.x
+1. Access the web admin page and log in
+2. Go to Grid tab > Grid Manager
+3. In the right menu select "Grid properties"
+4. Select "SNMP" menu
+5. Click "Enable SNMPv1/SNMPv2 Queries"
+6. Add your community
+7. Click Save & Close
+
+### Juniper
+#### Junos OS
+```
+set snmp description description
+set snmp location location
+set snmp contact contact
+set snmp community YOUR-COMMUNITY authorization read-only
+```
+
+### Palo Alto
+#### PANOS 6.x/7.x
+1. Access the web admin page and log in
+2. Go to Device tab > Setup
+3. Go to the sub-tab "Operations"
+4. Click "SNMP Setup"	
+5. Enter your SNMP community and then click "OK"
+6. Click Apply
+
+Note that you need to allow SNMP on the needed interfaces. To do that you need to create a network "Interface Mgmt" profile for standard interface and allow SNMP under "Device > Management > Management Interface Settings" for out of band management interface.
+
+
+## Operating systems
+### Linux (snmpd)
+
+Replace your snmpd.conf file by the example below and edit it with appropriate community in "RANDOMSTRINGGOESHERE".
+
+```
+vi /etc/snmp/snmpd.conf
+```
+
+```
+# Change RANDOMSTRINGGOESHERE to your preferred SNMP community string
+com2sec readonly  default         RANDOMSTRINGGOESHERE
+
+group MyROGroup v2c        readonly
+view all    included  .1                               80
+access MyROGroup ""      any       noauth    exact  all    none   none
+
+syslocation Rack, Room, Building, City, Country [GPSX,Y]
+syscontact Your Name <your@email.address>
+
+#Distro Detection
+extend .1.3.6.1.4.1.2021.7890.1 distro /usr/bin/distro
+```
+The LibreNMS server include a copy of this example here:
+
+```
+/opt/librenms/snmpd.conf.example
+```
+
+#### Restart the snmpd service:
+
+##### CentOS 6 / Red hat 6
+```
+service snmpd restart
+```
+##### CentOS 7 / Red hat 7
+```
+systemctl restart snmpd
+```
+##### Ubuntu
+```
+service snmpd restart
+```
+
+### Windows Server 2008 R2
+1. Log in to your Windows Server 2008 R2
+2. Start "Server Manager" under "Administrative Tools"
+3. Click "Features" and then click "Add Feature"
+5. Check (if not checked) "SNMP Service", click "Next" until "Install"
+6. Start "Services" under "Administrative Tools"
+7. Edit "SNMP Service" properties
+8. Go to the security tab
+9. In "Accepted community name" click "Add" to add your community string and permission
+10. In "Accept SNMP packets from these hosts" click "Add" and add your LibreNMS server IP address
+11. Validate change by clicking "Apply"
+
+### Windows Server 2012 R2
+1. Log in to your Windows Server 2012 R2
+2. Start "Server Manager" under "Administrative Tools"
+3. Click "Manage" and then "Add Roles and Features"
+4. Continue by pressing "Next" to the "Features" menu
+5. Install (if not installed) "SNMP Service"
+6. Start "Services" under "Administrative Tools"
+7. Edit "SNMP Service" properties
+8. Go to the security tab
+9. In "Accepted community name" click "Add" to add your community string and permission
+10. In "Accept SNMP packets from these hosts" click "Add" and add your LibreNMS server IP address
+11. Validate change by clicking "Apply"
diff --git a/mkdocs.yml b/mkdocs.yml
index 2e649cf00b..d3e98490a8 100644
--- a/mkdocs.yml
+++ b/mkdocs.yml
@@ -92,6 +92,7 @@ pages:
     - Support/Performance.md
     - Support/Poller Support.md
     - Support/Support-New-OS.md
+    - Support/SNMP-Configuration-Examples.md
 - hidden:
     - Ubuntu 14.04 (Nginx): Installation/Installation-Ubuntu-1404-Nginx.md
     - Ubuntu 14.04 (Apache): Installation/Installation-Ubuntu-1404-Apache.md