mirror/librenms-librenms
1
0
Fork 0
mirror of https://github.com/librenms/librenms.git synced 2024-10-07 16:52:45 +00:00
Code Issues Actions Packages Projects Releases Wiki Activity
Files
0b30ca1071cda71ce58a13a8526b0a2693f05d15
librenms-librenms/mibs/CISCO-WAN-3G-MIB
Adam Winberg 6e5a5c06f8 Added MIB
2016-04-19 08:52:02 +02:00

5725 lines
199 KiB
Plaintext
Raw Blame History

-- *****************************************************************
--
-- February 2009. Frank Fang
--
-- Copyright (c) 2007-2013 by cisco Systems Inc.
-- All rights reserved.
-- *****************************************************************
CISCO-WAN-3G-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY,
OBJECT-TYPE,
NOTIFICATION-TYPE,
Integer32,
Unsigned32,
Counter64,
Counter32,
Gauge32
FROM SNMPv2-SMI
MODULE-COMPLIANCE,
NOTIFICATION-GROUP,
OBJECT-GROUP
FROM SNMPv2-CONF
SnmpAdminString
FROM SNMP-FRAMEWORK-MIB
entPhysicalName,
entPhysicalIndex
FROM ENTITY-MIB
ifIndex
FROM IF-MIB
InetAddress,
InetAddressType
FROM INET-ADDRESS-MIB
RowStatus,
DisplayString,
TEXTUAL-CONVENTION,
TruthValue
FROM SNMPv2-TC
ciscoMgmt
FROM CISCO-SMI;
ciscoWan3gMIB MODULE-IDENTITY
LAST-UPDATED "201308120000Z"
ORGANIZATION "Cisco Systems, Inc."
CONTACT-INFO
"Cisco Systems
Customer Service
Postal: 170 W Tasman Drive
San Jose, CA 95134
USA
Tel: +1 800 553-NETS
E-mail: cs-3g@cisco.com
cs-4g@cisco.com"
DESCRIPTION
"This MIB module provides network management
support for Cisco cellular 3G and 4G LTE WAN products.
*** ABBREVIATIONS, ACRONYMS, AND SYMBOLS ***
1xRTT - 1 times Radio Transmission Technology.
3G - Third generation of mobile phones standards and
technologies.
4G - Fourth generation of mobile phones standards and
technologies
Azimuth - Angle of rotation of a satellite Dish.
BER - Bit Error Ratio.
BS - Base Station.
CDMA - Code Division Multiple Access.
dB - decibel.
dBm - power ratio in decibels (dB) of the measured power
referenced to one milliwatt (mW).
CnS - Control and Status proprietary protocol for
managing the control and status of the modem.
Ec/Io - ratio of received pilot energy, Ec, to total received
energy or the total power spectral density, Io.
EDGE - Enhanced Data rate for GSM Evolution.
EPS - Evolved Packet System
EVDO - EVolution Data Optimized.
FDD - Frequency Division Duplexing
GPRS - General Packet Radio Service.
GSM - Global System for Mobile communications.
GPS - Global Positioning System.
HSDPA - High Speed Downlink Packet Access.
HSPA - High Speed Packet Access.
HSUPA - High Speed Uplink Packet Access.
LBS - Location Based Service.
LTE - Long Term Evolution
MT - Mobile Termination.
PDP - Packet Data Protocol.
PLMN - Public Land Mobile Network.
QoS - Quality of Service.
RSSI - Received Signal Strength Indication.
SDU - Service Data Unit.
SER - SDU Error Ratio.
SIM - Subscriber Identity Module.
SMS - Short Messaging Service.
SNR - Signal to Noise Ratio.
TDD - Time Division Duplexing
UMTS - Universal Mobile Telecommunication System.
WCDMA - Wideband Code Division Multiple Access."
REVISION "201308120000Z"
DESCRIPTION
"Added new notifications c3gModemTemperOnsetRecoveryNotif,
c3gModemTemperAbateRecoveryNotif."
REVISION "201207250000Z"
DESCRIPTION
"Modified Description of the ciscoWan3gMIB
module.
Modified the description of c3gWanCommonTable,
c3gWanLbsCommonTable, c3gSmsCommonTable and all its objects
to emphazise that it is technology independent.
Added enumerated value lte to objects C3gServiceCapability,
c3gCurrentIdleDigitalMode, c3gGsmPacketService.
Modified the descriptions of c3gGsmIdentityTable, and all its
objects to emphazise that these objects are applicable to both
3G and 4G-LTE Technology.
Added new object c3gGpsState to the table c3gWanCommonTable.
Added enumerated value lteBand for c3gGsmCurrentBand.
Modified ciscoWan3gMIBGsmObjectGroup,
ciscoWan3gMIBSmsObjectGroup, ciscoWan3gMIBLbsObjectGroup,
ciscoWan3gMIBGsmObjectGroup description in Module
ciscoWan3gMIBCompliance, ciscoWan3gMIBCompliance1.
Added c3gGpsState to the group ciscoWan3gMIBCommonObjectGroup."
REVISION "201207100000Z"
DESCRIPTION
"Added enumerated values rate56kbps(12) to rate8dot4mbps(18) for
C3gUmtsQosLinkBitRate."
REVISION "201008110000Z"
DESCRIPTION
"Fixed spelling errors."
REVISION "201008040000Z"
DESCRIPTION
"Added c3gWanLbs and c3gWanSms.
Added ciscoWan3gMIBSmsObjectGroup and
ciscoWan3gMIBSmsObjectGroup.
Deprecated ciscoWan3gMIBCompliance and replaced
by ciscoWan3gMIBCompliance1."
REVISION "200902050000Z"
DESCRIPTION
"Initial version of this MIB module."
::= { ciscoMgmt 661 }
C3gServiceCapability ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"3G service capability:
oneXRtt(0) - 1xRTT
evDoRel0(1) - EVDO Revision 0
evDoRelA(2) - EVDO Revision A
evDoRelB(3) - EVDO Revision B
gprs(4) - GPRS
edge(5) - EDGE
umtsWcdma(6) - UMTS/WCDMA
hsdpa(7) - HSDPA
hsupa(8) - HSUPA
hspa(9) - HSPA
hspaPlus(10) - HSPA Plus
lteTdd(11) - LTE TDD
lteFdd (12) - LTE FDD"
SYNTAX BITS {
oneXRtt(0),
evDoRel0(1),
evDoRelA(2),
evDoRelB(3),
gprs(4),
edge(5),
umtsWcdma(6),
hsdpa(7),
hsupa(8),
hspa(9),
hspaPlus(10),
lteTdd(11),
lteFdd(12)
}
C3gRssi ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Generic RSSI range."
SYNTAX Integer32 (-150..0)
C3gEcIo ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Generic EcIo range."
SYNTAX Integer32 (-150..0)
C3gTemperature ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Generic temperature range."
SYNTAX Integer32 (-50..100)
C3gPdpType ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Generic PDP type."
SYNTAX INTEGER {
unknown(1),
ipV4(2),
ppp(3),
ipV6(4),
ipV4V6(5)
}
C3gUmtsQosTrafficClass ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"UMTS QoS traffic classes:
subscription(1) - based on user's subscription
conversational(2) - conversational
streaming(3) - streaming
interactive(4) - interactive
background(5) - background"
SYNTAX INTEGER {
subscription(1),
conversational(2),
streaming(3),
interactive(4),
background(5)
}
C3gUmtsQosLinkBitRate ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"UMTS QoS link bit rate:
subscription(1) - based on user's subscription
rate16kbps(2) - 16 Kbps
rate32kbps(3) - 32 Kbps
rate64kbps(4) - 64 Kbps
rate128kbps(5) - 128 Kbps
rate256kbps(6) - 256 Kbps
rate384kbps(7) - 384 Kbps
rate1dot8mbps(8) - 1.8 Mbps
rate3dot6mbps(9) - 3.6 Mbps
rate7dot2mbps(10) - 7.2 Mbps
rate14dot4mbps(11) - 14.4 Mbps
rate56kbps(12) - 56 Kbps
rate1dot15mbps(13) - 1.15 Mbps
rate1dot6mbps(14) - 1.6 Mbps
rate2dot1mbps(15) - 2.1 Mbps
rate2dot8mbps(16) - 2.8 Mbps
rate4dot2mbps(17) - 4.2 Mbps
rate8dot4mbps(18) - 8.4 Mbps"
SYNTAX INTEGER {
subscription(1),
rate16kbps(2),
rate32kbps(3),
rate64kbps(4),
rate128kbps(5),
rate256kbps(6),
rate384kbps(7),
rate1dot8mbps(8),
rate3dot6mbps(9),
rate7dot2mbps(10),
rate14dot4mbps(11),
rate56kbps(12),
rate1dot15mbps(13),
rate1dot6mbps(14),
rate2dot1mbps(15),
rate2dot8mbps(16),
rate4dot2mbps(17),
rate8dot4mbps(18)
}
C3gUmtsQosOrder ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"UMTS QoS delivery order:
subscription(1) - based on user's subscription
withDeliverOrder(2) - with delivery order
withoutDeliverOrder(3) - without delivery order"
SYNTAX INTEGER {
subscription(1),
withDeliverOrder(2),
withoutDeliverOrder(3)
}
C3gUmtsQosErroneousSdu ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"UMTS QoS Delivery of Erroneous Service Data Unit(SDU):
subscription(1) - based on user's subscription
noDetect(2) - no detect
errSduDeliver(3) - erroneous SDUs are delivered
errSduNotDeliver(4) - erroneous SDUs are not delivered"
SYNTAX INTEGER {
subscription(1),
noDetect(2),
errSduDeliver(3),
errSduNotDeliver(4)
}
C3gUmtsQosSer ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"UMTS QoS SDU error ratio:
subscription(1) - based on user's subscription
oneExpMinus2(2) - 1E-2
sevenExpMinus3(3) - 7E-3
oneExpMinus3(4) - 1E-3
oneExpMinus4(5) - 1E-4
oneExpMinus5(6) - 1E-5
oneExpMinus6(7) - 1E-6
oneExpMinus1(8) - 1E-1"
SYNTAX INTEGER {
subscription(1),
oneExpMinus2(2),
sevenExpMinus3(3),
oneExpMinus3(4),
oneExpMinus4(5),
oneExpMinus5(6),
oneExpMinus6(7),
oneExpMinus1(8)
}
C3gUmtsQosBer ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"UMTS QoS residual bit error ratio (BER):
subscription(1) - based on user's subscription
fiveExpMinus2(2) - 5E-2
oneExpMinus2(3) - 1E-2
fiveExpMinus3(4) - 5E-3
fourExpMinus3(5) - 4E-3
oneExpMinus3(6) - 1E-3
oneExpMinus4(7) - 1E-4
oneExpMinus5(8) - 1E-5
oneExpMinus6(9) - 1E-6
sixExpMinus8(10) - 6E-8"
SYNTAX INTEGER {
subscription(1),
fiveExpMinus2(2),
oneExpMinus2(3),
fiveExpMinus3(4),
fourExpMinus3(5),
oneExpMinus3(6),
oneExpMinus4(7),
oneExpMinus5(8),
oneExpMinus6(9),
sixExpMinus8(10)
}
C3gUmtsQosPriority ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"UMTS QoS traffic handling priority:
subscription(1) - based on user's subscription
level1(2) - priority level 1
level2(3) - priority level 2
level3(4) - priority level 3"
SYNTAX INTEGER {
subscription(1),
level1(2),
level2(3),
level3(4)
}
C3gUmtsQosSrcStatDescriptor ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"UMTS QoS source statistics descriptor:
unknown(1) - unknown
speech(2) - speech"
SYNTAX INTEGER {
unknown(1),
speech(2)
}
C3gUmtsQosSignalIndication ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"UMTS QoS signalling indication:
notOptimized(1) - not optimized for signalling traffic
optimized(2) - optimized for signalling traffic"
SYNTAX INTEGER {
notOptimized(1),
optimized(2)
}
C3gGprsQosPrecedence ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"GPRS QoS precedence:
subscription(1) - based on user's subscription
highPriority(2) - high priority
normalPriority(3) - normal priority
lowPriority(4) - low priority"
SYNTAX INTEGER {
subscription(1),
highPriority(2),
normalPriority(3),
lowPriority(4)
}
C3gGprsQosDelay ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"GPRS QoS delay classes:
subscription(1) - based on user's subscription
delayClass1(2) - delay class 1
delayClass2(3) - delay class 2
delayClass3(4) - delay class 3
delayClass4(5) - delay class 4"
SYNTAX INTEGER {
subscription(1),
delayClass1(2),
delayClass2(3),
delayClass3(4),
delayClass4(5)
}
C3gGprsQosReliability ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"GPRS QoS reliability:
subscription(1) - based on user's subscription
ackGtpLlcRlcProtData(2) - acknowledged GTP, LLC, and RLC;
protected data
unAckGtpAckLlcRlcProtData(3) - unacknowledged GTP, acknowledged
LLC and RLC; protected data
unAckGtpLlcAckRlcProtData(4) - unacknowledged GTP and LLC,
acknowledged RLC; protected data
unAckGtpLlcRlcProtData(5) - unacknowledged GTP, LLC, and
RLC; protected data
unAckGtpLlcRlcUnProtData(6) - unacknowledged GTP, LLC, and
RLC; unprotected data"
SYNTAX INTEGER {
subscription(1),
ackGtpLlcRlcProtData(2),
unAckGtpAckLlcRlcProtData(3),
unAckGtpLlcAckRlcProtData(4),
unAckGtpLlcRlcProtData(5),
unAckGtpLlcRlcUnProtData(6)
}
C3gGprsQosPeakRate ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"GPRS QoS peak rate:
subscription(1) - based on user's subscription
upTo1kops(2) - up to 1000 octet/second
upTo2kops(3) - up to 2000 octet/second
upTo4kops(4) - up to 4000 octet/second
upTo8kops(5) - up to 8000 octet/second
upTo16kops(6) - up to 16000 octet/second
upTo32kops(7) - up to 32000 octet/second
upTo64kops(8) - up to 64000 octet/second
upTo128kops(9) - up to 128000 octet/second
upTo256kops(10) - up to 256000 octet/second"
SYNTAX INTEGER {
subscription(1),
upTo1kops(2),
upTo2kops(3),
upTo4kops(4),
upTo8kops(5),
upTo16kops(6),
upTo32kops(7),
upTo64kops(8),
upTo128kops(9),
upTo256kops(10)
}
C3gGprsQosMeanRate ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"GPRS QoS mean rate:
subscription(1) - based on user's subscription
rate100(2) - 100 octet/hour
rate200(3) - 200 octet/hour
rate500(4) - 500 octet/hour
rate1k(5) - 1000 octet/hour
rate2k(6) - 2000 octet/hour
rate5k(7) - 5000 octet/hour
rate10k(8) - 10000 octet/hour
rate20k(9) - 20000 octet/hour
rate50k(10) - 50000 octet/hour
rate100k(11) - 100000 octet/hour
rate200k(12) - 200000 octet/hour
rate500k(13) - 500000 octet/hour
rate1m(14) - 1000000 octet/hour
rate2m(15) - 2000000 octet/hour
rate5m(16) - 5000000 octet/hour
rate10m(17) - 10000000 octet/hour
rate20m(18) - 20000000 octet/hour
rate50m(19) - 50000000 octet/hour
resv1(20) - reserved 1 (for future use)
resv2(21) - reserved 2 (for future use)
resv3(22) - reserved 3 (for future use)
resv4(23) - reserved 4 (for future use)
resv5(24) - reserved 5 (for future use)
resv6(25) - reserved 6 (for future use)
resv7(26) - reserved 7 (for future use)
resv8(27) - reserved 8 (for future use)
resv9(28) - reserved 9 (for future use)
resv10(29) - reserved 10 (for future use)
resv11(30) - reserved 11 (for future use)
resv12(31) - reserved 12 (for future use)
bestEffort(32) - best effort"
SYNTAX INTEGER {
subscription(1),
rate100(2),
rate200(3),
rate500(4),
rate1k(5),
rate2k(6),
rate5k(7),
rate10k(8),
rate20k(9),
rate50k(10),
rate100k(11),
rate200k(12),
rate500k(13),
rate1m(14),
rate2m(15),
rate5m(16),
rate10m(17),
rate20m(18),
rate50m(19),
resv1(20),
resv2(21),
resv3(22),
resv4(23),
resv5(24),
resv6(25),
resv7(26),
resv8(27),
resv9(28),
resv10(29),
resv11(30),
resv12(31),
bestEffort(32)
}
-- Textual Conventions definition will be defined before this objects
ciscoWan3gMIBNotifs OBJECT IDENTIFIER
::= { ciscoWan3gMIB 0 }
ciscoWan3gMIBObjects OBJECT IDENTIFIER
::= { ciscoWan3gMIB 1 }
ciscoWan3gMIBConform OBJECT IDENTIFIER
::= { ciscoWan3gMIB 2 }
c3gWanCommonTable OBJECT-TYPE
SYNTAX SEQUENCE OF C3gWanCommonEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Cellular common objects table which is technology
independent."
::= { ciscoWan3gMIBObjects 1 }
c3gWanCommonEntry OBJECT-TYPE
SYNTAX C3gWanCommonEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (conceptual row) in the c3gWanCommonTable."
INDEX { entPhysicalIndex }
::= { c3gWanCommonTable 1 }
C3gWanCommonEntry ::= SEQUENCE {
c3gStandard INTEGER,
c3gCapability C3gServiceCapability,
c3gModemState INTEGER,
c3gPreviousServiceType C3gServiceCapability,
c3gCurrentServiceType C3gServiceCapability,
c3gRoamingStatus INTEGER,
c3gCurrentSystemTime DisplayString,
c3gConnectionStatus INTEGER,
c3gNotifRadioService C3gServiceCapability,
c3gNotifRssi C3gRssi,
c3gNotifEcIo C3gEcIo,
c3gModemTemperature C3gTemperature,
c3gRssiOnsetNotifThreshold C3gRssi,
c3gRssiAbateNotifThreshold C3gRssi,
c3gEcIoOnsetNotifThreshold C3gEcIo,
c3gEcIoAbateNotifThreshold C3gEcIo,
c3gModemTemperOnsetNotifThreshold C3gTemperature,
c3gModemTemperAbateNotifThreshold C3gTemperature,
c3gModemReset INTEGER,
c3gModemUpNotifEnabled TruthValue,
c3gModemDownNotifEnabled TruthValue,
c3gServiceChangedNotifEnabled TruthValue,
c3gNetworkChangedNotifEnabled TruthValue,
c3gConnectionStatusChangedNotifFlag BITS,
c3gRssiOnsetNotifFlag C3gServiceCapability,
c3gRssiAbateNotifFlag C3gServiceCapability,
c3gEcIoOnsetNotifFlag C3gServiceCapability,
c3gEcIoAbateNotifFlag C3gServiceCapability,
c3gModemTemperOnsetNotifEnabled TruthValue,
c3gModemTemperAbateNotifEnabled TruthValue,
c3gGpsState TruthValue
}
c3gStandard OBJECT-TYPE
SYNTAX INTEGER {
cdma(1),
gsm(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Cellular Standard: GSM (Global System for Mobile
communications, 3GPP), CDMA (Code Division Multiple
Access, 3GPP-2). GSM standard also include 4G-LTE
technology mode"
::= { c3gWanCommonEntry 1 }
c3gCapability OBJECT-TYPE
SYNTAX C3gServiceCapability
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Cellular service capability. It currently includes the 2G,
3G and 4G-LTE standard."
::= { c3gWanCommonEntry 2 }
c3gModemState OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
up(2),
down(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Cellular modem state, up(2) indicates modem can be detected
and down(3) indicates modem can not be detected."
DEFVAL { down }
::= { c3gWanCommonEntry 3 }
c3gPreviousServiceType OBJECT-TYPE
SYNTAX C3gServiceCapability
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the previous service type when service
type changes."
::= { c3gWanCommonEntry 4 }
c3gCurrentServiceType OBJECT-TYPE
SYNTAX C3gServiceCapability
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the current service type when service
type changes."
::= { c3gWanCommonEntry 5 }
c3gRoamingStatus OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
roaming(2),
home(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Cellular current roaming status."
::= { c3gWanCommonEntry 6 }
c3gCurrentSystemTime OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..64))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Cellular current system time received from base station."
::= { c3gWanCommonEntry 7 }
c3gConnectionStatus OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
error(2),
connecting(3),
dormant(4),
connected(5),
disconnected(6),
idle(7),
active(8),
inactive(9)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the current connection status."
::= { c3gWanCommonEntry 8 }
c3gNotifRadioService OBJECT-TYPE
SYNTAX C3gServiceCapability
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object is used as one of the var-bind object when
notification for RSSI or Ec/Io is generated. This object
indicates which service generates the notification."
::= { c3gWanCommonEntry 9 }
c3gNotifRssi OBJECT-TYPE
SYNTAX C3gRssi
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object is used as one of the var-bind object when
notification for RSSI is generated. The relevant RSSI will be
copied into c3gNotifRssi which corresponds to the service
indicated in c3gNotifRadioService object. This object will
reflect the value of one of the following objects:
c3gCurrent1xRttRssi, c3gCurrentEvDoRssi and c3gCurrentGsmRssi.
User should not use this object to get the current RSSI value as
this object is used to indicate the RSSI value that triggers
c3gRssiOnsetNotif or c3gRssiAbateNotif notification."
::= { c3gWanCommonEntry 10 }
c3gNotifEcIo OBJECT-TYPE
SYNTAX C3gEcIo
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object is used as one of the var-bind object when
notification for Ec/Io is generated. The relevant Ec/Io will
be copied into c3gNotifEcIo which corresponds to the service
indicated in c3gNotifRadioService object. This object will
reflect the value of one of the following objects:
c3gCurrent1xRttEcIo, c3gCurrentEvDoEcIo and c3gCurrentGsmEcIo.
User should not use this object to get the current Ec/Io value
as this object is used to indicate the Ec/Io value that triggers
c3gEcIoOnsetNotif or c3gEcIoAbateNotif notification."
::= { c3gWanCommonEntry 11 }
c3gModemTemperature OBJECT-TYPE
SYNTAX C3gTemperature
UNITS "degrees Celsius"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The modem temperature."
::= { c3gWanCommonEntry 12 }
c3gRssiOnsetNotifThreshold OBJECT-TYPE
SYNTAX C3gRssi
UNITS "dBm"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The RSSI onset threshold value. If RSSI goes below the
threshold and the service bit in c3gRssiOnsetNotifFlag is
set, the c3gRssiOnsetNotif notification for that service
will be sent. The absolute value of
c3gRssiAbateNotifThreshold should be less than or equal to
the absolute value of c3gRssiOnsetNotifThreshold
(|c3gRssiAbateNotifThreshold| <= |c3gRssiOnsetNotifThreshold|).
e.g. setting c3gRssiAbateNotifThreshold to -115 dBm and then
setting c3gRssiOnsetNotifThreshold to -110 dBm is not allowed
and will be rejected."
DEFVAL { -150 }
::= { c3gWanCommonEntry 13 }
c3gRssiAbateNotifThreshold OBJECT-TYPE
SYNTAX C3gRssi
UNITS "dBm"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The RSSI abate threshold value. If RSSI goes above the
threshold and the service bit in c3gRssiAbateNotifFlag is
set, the c3gRssiAbateNotif notification for that service will
be sent. The absolute value of c3gRssiAbateNotifThreshold
should be less than or equal to the absolute value of
c3gRssiOnsetNotifThreshold (|c3gRssiAbateNotifThreshold| <=
|c3gRssiOnsetNotifThreshold|). e.g. setting
c3gRssiAbateNotifThreshold to -115 dBm and then setting
c3gRssiOnsetNotifThreshold to -110 dBm is not allowed
and will be rejected."
DEFVAL { 0 }
::= { c3gWanCommonEntry 14 }
c3gEcIoOnsetNotifThreshold OBJECT-TYPE
SYNTAX C3gEcIo
UNITS "dB"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The EcIo onset threshold value. If EcIo goes below the
threshold and the service bit in c3gEcIoOnsetNotifFlag is set,
the c3gEcIoOnsetNotif notification for that service will be
sent. The absolute value of c3gEcIoAbateNotifThreshold should
be less than or equal to the absolute value of
c3gEcIoOnsetNotifThreshold (|c3gEcIoAbateNotifThreshold| <=
|c3gEcIoOnsetNotifThreshold|). e.g. setting
c3gEcIoAbateNotifThreshold to -15 dB and then setting
c3gEcIoOnsetNotifThreshold to -10 dB is not allowed and will
be rejected."
DEFVAL { -150 }
::= { c3gWanCommonEntry 15 }
c3gEcIoAbateNotifThreshold OBJECT-TYPE
SYNTAX C3gEcIo
UNITS "dB"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The threshold value that if EcIo goes above the threshold and
the service bit in c3gEcIoAbateNotifFlag is set, the
c3gEcIoAbateNotif notification for that service will be sent.
The absolute value of c3gEcIoAbateNotifThreshold
should be less than or equal to the absolute value of
c3gEcIoOnsetNotifThreshold (|c3gEcIoAbateNotifThreshold| <=
|c3gEcIoOnsetNotifThreshold|). e.g. setting
c3gEcIoOnsetNotifThreshold to -15 dB and then setting
c3gEcIoAbateNotifThreshold to -10 dB is not allowed and will
be rejected."
DEFVAL { 0 }
::= { c3gWanCommonEntry 16 }
c3gModemTemperOnsetNotifThreshold OBJECT-TYPE
SYNTAX C3gTemperature
UNITS "degrees Celsius"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The modem temperature onset threshold value. If modem
temperature goes above the threshold and the value of
c3gModemTemperOnsetNotifEnabled is 'true',
the c3gModemTemperOnsetNotif notification will be sent.
The value of c3gModemTemperAbateNotifThreshold should be less
than or equal to the value of
c3gModemTemperOnsetNotifThreshold. e.g. setting
c3gModemTemperAbateNotifThreshold to 50 degree Celsius and
then setting c3gModemTemperOnsetNotifThreshold to
40 degree Celsius is not allowed and will be rejected."
DEFVAL { 100 }
::= { c3gWanCommonEntry 17 }
c3gModemTemperAbateNotifThreshold OBJECT-TYPE
SYNTAX C3gTemperature
UNITS "degrees Celsius"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The modem temperature abate threshold value. If modem
temperature goes below the threshold and the value of
c3gModemTemperAbateNotifEnabled is 'true', the
c3gModemTemperAbateNotif notification will be sent. The value
of c3gModemTemperAbateNotifThreshold should be less than or
equal to the value of c3gModemTemperOnsetNotifThreshold.
e.g. setting c3gModemTemperAbateNotifThreshold to 50 degree
Celsius and then setting c3gModemTemperOnsetNotifThreshold
to 40 degree Celsius is not allowed and will be rejected."
DEFVAL { -50 }
::= { c3gWanCommonEntry 18 }
c3gModemReset OBJECT-TYPE
SYNTAX INTEGER {
reset(1),
powerCycle(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to reset or power-cycle the modem."
::= { c3gWanCommonEntry 19 }
c3gModemUpNotifEnabled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to enable/disable the generation of modem
up notification c3gModemUpNotif."
DEFVAL { false }
::= { c3gWanCommonEntry 20 }
c3gModemDownNotifEnabled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to enable/disable the generation of modem
down notification c3gModemDownNotif."
DEFVAL { false }
::= { c3gWanCommonEntry 21 }
c3gServiceChangedNotifEnabled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to enable/disable the generation of service
changed notification c3gServiceChangedNotif."
DEFVAL { false }
::= { c3gWanCommonEntry 22 }
c3gNetworkChangedNotifEnabled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to enable/disable the generation of network
changed notification c3gNetworkChangedNotif."
DEFVAL { false }
::= { c3gWanCommonEntry 23 }
c3gConnectionStatusChangedNotifFlag OBJECT-TYPE
SYNTAX BITS {
unknown(0),
error(1),
connecting(2),
dormant(3),
connected(4),
disconnected(5),
idle(6),
active(7),
inactive(8)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is the flag bitmap to control the generation of
notification c3gConnectionStatusChangedNotif. e.g. setting bit
0 (error(0)) to 1 and bit 4 (disconnected(4)) to 1 will cause
the notification c3gConnectionStatusChangedNotif to be
generated when object c3gConnetionStatus changes the status to
error or disconnected. The default value of this object is
'00'H."
::= { c3gWanCommonEntry 24 }
c3gRssiOnsetNotifFlag OBJECT-TYPE
SYNTAX C3gServiceCapability
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is the flag bitmap to control the generation of
notification c3gRssiOnsetNotif. Each bit represents a service
as defined in C3gServiceCapability, set the bit value to 1 to
enable (and 0 to disable) the generation of notification
c3gRssiOnsetNotif for that service. The default value of this
object is all bits are 0."
::= { c3gWanCommonEntry 25 }
c3gRssiAbateNotifFlag OBJECT-TYPE
SYNTAX C3gServiceCapability
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is the flag bitmap to control the generation of
notification c3gRssiAbateNotif. Each bit represents a service
as defined in C3gServiceCapability, set the bit value to 1 to
enable (and 0 to disable) the generation of notification
c3gRssiAbateNotif for that service. The default value of this
object is all bits are 0."
::= { c3gWanCommonEntry 26 }
c3gEcIoOnsetNotifFlag OBJECT-TYPE
SYNTAX C3gServiceCapability
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is the flag bitmap to control the generation of
notification c3gEcIoOnsetNotif. Each bit represents a service
as defined in C3gServiceCapability, set the bit value to 1 to
enable (and 0 to disable) the generation of notification
c3gEcIoOnsetNotif for that service. The default value of this
object is all bits are 0."
::= { c3gWanCommonEntry 27 }
c3gEcIoAbateNotifFlag OBJECT-TYPE
SYNTAX C3gServiceCapability
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is the flag bitmap to control the generation of
notification c3gEcIoAbateNotif. Each bit represents a service
as defined in C3gServiceCapability, set the bit value to 1 to
enable (and 0 to disable) the generation of notification
c3gEcIoAbateNotif for that service. The default value of this
object is all bits are 0."
::= { c3gWanCommonEntry 28 }
c3gModemTemperOnsetNotifEnabled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to enable/disable the generation of
c3gModemTemperOnsetNotif notification."
DEFVAL { false }
::= { c3gWanCommonEntry 29 }
c3gModemTemperAbateNotifEnabled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to enable/disable the generation of
c3gModemTemperAbateNotif notification."
DEFVAL { false }
::= { c3gWanCommonEntry 30 }
c3gGpsState OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to determine or enable/disable
the GPS state."
DEFVAL { false }
::= { c3gWanCommonEntry 31 }
c3gWanCdma OBJECT IDENTIFIER
::= { ciscoWan3gMIBObjects 2 }
c3gWanGsm OBJECT IDENTIFIER
::= { ciscoWan3gMIBObjects 3 }
c3gWanLbs OBJECT IDENTIFIER
::= { ciscoWan3gMIBObjects 4 }
c3gWanSmsCommon OBJECT IDENTIFIER
::= { ciscoWan3gMIBObjects 5 }
c3gCdmaSessionTable OBJECT-TYPE
SYNTAX SEQUENCE OF C3gCdmaSessionEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table describes wireless session (link) created when a
modem connects to a particular cellular network. One or more
logical calls can be placed over wireless session(link). These
logical calls are represented in the c3gCdmaConnectionTable."
::= { c3gWanCdma 1 }
c3gCdmaSessionEntry OBJECT-TYPE
SYNTAX C3gCdmaSessionEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (conceptual row) in the c3gCdmaSessionTable."
INDEX { entPhysicalIndex }
::= { c3gCdmaSessionTable 1 }
C3gCdmaSessionEntry ::= SEQUENCE {
c3gCdmaTotalCallDuration Counter64,
c3gCdmaTotalTransmitted Counter64,
c3gCdmaTotalReceived Counter64,
c3gHdrDdtmPreference INTEGER
}
c3gCdmaTotalCallDuration OBJECT-TYPE
SYNTAX Counter64
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total duration of all calls."
::= { c3gCdmaSessionEntry 1 }
c3gCdmaTotalTransmitted OBJECT-TYPE
SYNTAX Counter64
UNITS "bytes"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total data transmitted for all calls. It is the total amount
of data transmitted by modem, not to be confused with the number
of bytes transmitted through the interface."
::= { c3gCdmaSessionEntry 2 }
c3gCdmaTotalReceived OBJECT-TYPE
SYNTAX Counter64
UNITS "bytes"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total data received for all calls. It is the total amount of
data received by modem, not to be confused with the number of
bytes received from the interface."
::= { c3gCdmaSessionEntry 3 }
c3gHdrDdtmPreference OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
off(2),
on(3),
noChange(4)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"HDR Data Dedicated Transmission Mode (DDTM) preference:
unknown(1) - DDTM preference is unknown
off(2) - DDTM preference set to OFF
on(3) - DDTM preference set to ON
noChange(4) - DDTM preference is no change"
DEFVAL { unknown }
::= { c3gCdmaSessionEntry 4 }
c3gCdmaConnectionTable OBJECT-TYPE
SYNTAX SEQUENCE OF C3gCdmaConnectionEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Cellular 3G CDMA connection table. This table describes
logical connections/calls over wireless link, the wireless link
is described in c3gCdmaSessionTable."
::= { c3gWanCdma 2 }
c3gCdmaConnectionEntry OBJECT-TYPE
SYNTAX C3gCdmaConnectionEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (conceptual row) in the c3gCdmaConnectionTable."
INDEX { ifIndex }
::= { c3gCdmaConnectionTable 1 }
C3gCdmaConnectionEntry ::= SEQUENCE {
c3gOutgoingCallNumber DisplayString,
c3gHdrAtState INTEGER,
c3gHdrSessionState INTEGER,
c3gUati DisplayString,
c3gColorCode Unsigned32,
c3gRati Unsigned32,
c3gHdrSessionDuration Unsigned32,
c3gHdrSessionStart Unsigned32,
c3gHdrSessionEnd Unsigned32,
c3gAuthStatus INTEGER,
c3gHdrDrc Unsigned32,
c3gHdrDrcCover Unsigned32,
c3gHdrRri INTEGER,
c3gMobileIpErrorCode Integer32,
c3gCdmaCurrentTransmitted Counter64,
c3gCdmaCurrentReceived Counter64,
c3gCdmaCurrentCallStatus INTEGER,
c3gCdmaCurrentCallDuration Unsigned32,
c3gCdmaCurrentCallType INTEGER,
c3gCdmaLastCallDisconnReason INTEGER,
c3gCdmaLastConnError INTEGER
}
c3gOutgoingCallNumber OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..64))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Phone number of outgoing call."
::= { c3gCdmaConnectionEntry 1 }
c3gHdrAtState OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
inactive(2),
acquisition(3),
sync(4),
idle(5),
access(6),
connected(7)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"High Data Rate (HDR) Access Terminal (AT) state."
DEFVAL { unknown }
::= { c3gCdmaConnectionEntry 2 }
c3gHdrSessionState OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
open(2),
close(3),
addressManagementProtocolSetup(4),
atInitiated(5),
anInitiated(6)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"High Data Rate (HDR) session state."
::= { c3gCdmaConnectionEntry 3 }
c3gUati OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..64))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Unicast Access Terminal Identifier (UATI), AT seeking access
to the 1 times EV-DO system receives a UATI allocated from the
system after setting up a radio traffic channel with a base
station."
::= { c3gCdmaConnectionEntry 4 }
c3gColorCode OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Color code. A sync channel may be used by the base station
to communicate administrative information to a mobile station.
For example, a base station may transmit a base station ID to a
user, a color code and administrative information identifying
system status."
::= { c3gCdmaConnectionEntry 5 }
c3gRati OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Random Access Terminal Identifier (RATI). AT transmits a
UATI request message to the ANC using the RATI to make a UATI
allocation request."
::= { c3gCdmaConnectionEntry 6 }
c3gHdrSessionDuration OBJECT-TYPE
SYNTAX Unsigned32
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"HDR connection session duration. It is the duration
between c3gHdrSessionStart and c3gHdrSessionEnd."
DEFVAL { 0 }
::= { c3gCdmaConnectionEntry 7 }
c3gHdrSessionStart OBJECT-TYPE
SYNTAX Unsigned32
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"HDR connection session starting time."
DEFVAL { 0 }
::= { c3gCdmaConnectionEntry 8 }
c3gHdrSessionEnd OBJECT-TYPE
SYNTAX Unsigned32
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"HDR connection session ending time."
DEFVAL { 0 }
::= { c3gCdmaConnectionEntry 9 }
c3gAuthStatus OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
notAuthenticated(2),
authenticated(3),
failed(4),
authenticationDisabled(5)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Connection authentication status:
unknown(1) - authentication status is unknown
notAuthenticated(2) - not yet authenticated.
authenticated(3) - authenticated.
failed(4) - authentication failed.
authenticationDisabled(5) - authentication disabled"
DEFVAL { unknown }
::= { c3gCdmaConnectionEntry 10 }
c3gHdrDrc OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"High Data Rate (HDR) Data Rate Control (DRC). AT provides
requests for data transmissions by sending a Data Rate Control,
DRC, message via a specific channel referred to as the DRC
channel."
DEFVAL { 0 }
::= { c3gCdmaConnectionEntry 11 }
c3gHdrDrcCover OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"HDR DRC cover. The DRC cover is a coding applied to
identify the sector from which the data is to be transmitted.
In one embodiment, the DRC cover is a Walsh code applied to
the DRC value, wherein a unique code corresponds to each sector
in the Active Set of the AT."
DEFVAL { 0 }
::= { c3gCdmaConnectionEntry 12 }
c3gHdrRri OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
pilotOnly(2),
rri9dot6kbps(3),
rri19dot2kbps(4),
rri38dot4kbps(5),
rri76dot8kbps(6),
rri153dot6kbps(7)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"HDR Rate Request Indicator (RRI). RRI provides the
structure of a frame currently being transmitted when frames
are transmitted at different rates. Services at different rates
are reliably provided by the RRI:
unknown(1) - RRI unknown
pilotOnly(2) - pilot channel only
rri9dot6kbps(3) - RRI is 9.6 Kbit/s
rri19dot2kbps(4) - RRI is 19.2 Kbit/s
rri38dot4kbps(5) - RRI is 38.4 Kbit/s
rri76dot8kbps(6) - RRI is 76.8 Kbit/s
rri153dot6kbps(7) - RRI is 153.6 Kbit/s"
DEFVAL { unknown }
::= { c3gCdmaConnectionEntry 13 }
c3gMobileIpErrorCode OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Mobile IP error code (please refer to RFC 2002)."
::= { c3gCdmaConnectionEntry 14 }
c3gCdmaCurrentTransmitted OBJECT-TYPE
SYNTAX Counter64
UNITS "bytes"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Current number of bytes transmitted by modem for current
connection."
::= { c3gCdmaConnectionEntry 15 }
c3gCdmaCurrentReceived OBJECT-TYPE
SYNTAX Counter64
UNITS "bytes"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Current number of bytes received by modem for current
connection."
::= { c3gCdmaConnectionEntry 16 }
c3gCdmaCurrentCallStatus OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
error(2),
connecting(3),
dormant(4),
connected(5),
disconnected(6)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Current call status."
::= { c3gCdmaConnectionEntry 17 }
c3gCdmaCurrentCallDuration OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Current call duration."
DEFVAL { 0 }
::= { c3gCdmaConnectionEntry 18 }
c3gCdmaCurrentCallType OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
asyncData(2),
voiceCall(3),
packet1xRttCall(4),
atAsyncDataCall(5),
atVoiceCall(6),
atPacketCall(7),
faxCall(8),
smsCall(9),
otaCall(10),
testCall(11),
callWaiting(12),
positionDetermination(13),
dormant(14),
e911Call(15)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Current call type."
::= { c3gCdmaConnectionEntry 19 }
c3gCdmaLastCallDisconnReason OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
modemOffline(2),
modemCdmaLocTilPowCyc(3),
noService(4),
abnormalCallEnd(5),
baseStatIntercept(6),
baseStatRelease(7),
baseStatReleaseNoReas(8),
baseStatReleaseSoRej(9),
incomingCall(10),
baseStatAlertStop(11),
clientEndedCall(12),
activationEndedOtasp(13),
ndssFailure(14),
maxAccesProbTransmit(15),
persistTestFailure(16),
ruimNotPresent(17),
accessAttemptInProg(18),
reasonUnspecified(19),
recdRetryOrder(20),
modemLocked(21),
gpsCallEnded(22),
smsCallEnded(23),
noConcurrentService(24),
noResponseFromBs(25),
rejectedByBs(26),
notCompatConcurServ(27),
accessBlockedByBs(28),
alreadyOnTraffChann(29),
emergencyCall(30),
dataCallEnded(31),
busyHdr(32),
billingOrAuthErrHdr(33),
sysChangeDueToPrlHdr(34),
hdrExitDueToPrl(35),
noSessionHdr(36),
callEndedHdr(37)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Last call disconnect reason:
unknown(1) - Unknown
modemOffline(2) - Modem offline
modemCdmaLocTilPowCyc(3) - Modem CDMA locked till power cycle
noService(4) - No service
abnormalCallEnd(5) - Abnormal call end
baseStatIntercept(6) - Base station intercept
baseStatRelease(7) - Base station release
baseStatReleaseNoReas(8) - Base station release (No reason)
baseStatReleaseSoRej(9) - Base station release (SO reject)
incomingCall(10) - Incoming call
baseStatAlertStop(11) - Base station alert stop
clientEndedCall(12) - Client ended call
activationEndedOtasp(13) - Activation ended OTASP (Over-
The-Air Service Provisioning)
ndssFailure(14) - NDSS (Network and Distributed
System Security) failure
maxAccesProbTransmit(15) - Max access probes transmitted
persistTestFailure(16) - Persistence test failure
ruimNotPresent(17) - RUIM (Removable User Identity
Module) not present
accessAttemptInProg(18) - Access attempt in progress
reasonUnspecified(19) - Reason unspecified
recdRetryOrder(20) - Recd retry order
modemLocked(21) - Modem Locked
gpsCallEnded(22) - GPS call ended
smsCallEnded(23) - SMS (Short Message Service)
call ended
noConcurrentService(24) - No concurrent service
noResponseFromBs(25) - No response from BS (Base station)
rejectedByBs(26) - Rejected by BS
notCompatConcurServ(27) - Not compatible concurrent service
accessBlockedByBs(28) - Access blocked by BS
alreadyOnTraffChann(29) - Already on Traffic channel
emergencyCall(30) - Emergency call
dataCallEnded(31) - Data call ended
busyHdr(32) - Busy (HDR)
billingOrAuthErrHdr(33) - Billing or Auth error (HDR)
sysChangeDueToPrlHdr(34) - System change due to PRL (HDR)
hdrExitDueToPrl(35) - HDR exit due to PRL (HDR)
noSessionHdr(36) - No Session (HDR)
callEndedHdr(37) - Call ended (HDR)"
::= { c3gCdmaConnectionEntry 20 }
c3gCdmaLastConnError OBJECT-TYPE
SYNTAX INTEGER {
none(1),
invalidClientId(2),
badCallType(3),
badServiceType(4),
expectingNumber(5),
nullNumberBuffer(6),
invalidDigits(7),
outOfRangeNumber(8),
nullAalphaBuffer(9),
outOfRangeAlphaNumber(10),
invalidOtaspActivatCode(11),
modemOffline(12),
modemLocked(13),
unsupportedFlash(14),
dialedNumberProhibited(15),
onlyE911Calls(16),
modemInUse(17),
unsupportedServiceType(18),
wrongCallType(19),
invalidCommandCallState(20),
invalidCommandModemState(21),
noValidService(22),
cannotAnswerIncomingCall(23),
badPrivacySetting(24),
noCommandBuffers(25),
communicationProblem(26),
unspecifiedError(27),
invalidLastActiveNetwork(28),
noCollocatedHdr(29),
uimNotPresent(30)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Last connect error:
none(1) - None
invalidClientId(2) - Invalid client ID
badCallType(3) - Bad call type
badServiceType(4) - Bad service type
expectingNumber(5) - Expecting number
nullNumberBuffer(6) - Null number buffer
invalidDigits(7) - Invalid digits
outOfRangeNumber(8) - Out of range number
nullAalphaBuffer(9) - Null alpha buffer
outOfRangeAlphaNumber(10) - Out of range alpha number
invalidOtaspActivatCode(11) - Invalid OTASP activation code
modemOffline(12) - Modem offline
modemLocked(13) - Modem locked
unsupportedFlash(14) - Unsupported flash
dialedNumberProhibited(15) - Dialed number prohibited
onlyE911Calls(16) - Only E911 calls
modemInUse(17) - Modem in use
unsupportedServiceType(18) - Unsupported service type
wrongCallType(19) - Wrong call type
invalidCommandCallState(20) - Invalid command (call state)
invalidCommandModemState(21) - Invalid command (modem state)
noValidService(22) - No valid service
cannotAnswerIncomingCall(23) - Cannot answer incoming call
badPrivacySetting(24) - Bad privacy setting
noCommandBuffers(25) - No command buffers
communicationProblem(26) - Communication problem
unspecifiedError(27) - Unspecified error
invalidLastActiveNetwork(28) - Invalid last active network
noCollocatedHdr(29) - No collocated HDR
uimNotPresent(30) - UIM (User Identity Module) not
present"
::= { c3gCdmaConnectionEntry 21 }
c3gCdmaIdentityTable OBJECT-TYPE
SYNTAX SEQUENCE OF C3gCdmaIdentityEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Cellular 3G CDMA identity table."
::= { c3gWanCdma 3 }
c3gCdmaIdentityEntry OBJECT-TYPE
SYNTAX C3gCdmaIdentityEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (conceptual row) in the c3gCdmaIdentityTable."
INDEX { entPhysicalIndex }
::= { c3gCdmaIdentityTable 1 }
C3gCdmaIdentityEntry ::= SEQUENCE {
c3gEsn DisplayString,
c3gModemActivationStatus INTEGER,
c3gAccountActivationDate DisplayString,
c3gCdmaRoamingPreference INTEGER,
c3gPrlVersion Unsigned32,
c3gMdn DisplayString,
c3gMsid DisplayString,
c3gMsl DisplayString
}
c3gEsn OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..128))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates Electronic Serial Number (ESN)."
::= { c3gCdmaIdentityEntry 1 }
c3gModemActivationStatus OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
activated(2),
notActivated(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Modem activation status."
DEFVAL { unknown }
::= { c3gCdmaIdentityEntry 2 }
c3gAccountActivationDate OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..128))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Modem account activation date."
::= { c3gCdmaIdentityEntry 3 }
c3gCdmaRoamingPreference OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
home(2),
affiliated(3),
any(4)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object indicates the roaming preference:
unknown(1) - preference unknown
home(2) - home networks only
affiliated(3) - roaming on affiliated networks
any(4) - roaming on any network"
DEFVAL { any }
::= { c3gCdmaIdentityEntry 4 }
c3gPrlVersion OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Preferred Roaming List (PRL) version."
DEFVAL { 0 }
::= { c3gCdmaIdentityEntry 5 }
c3gMdn OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..64))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Mobile Directory Number (MDN), a dialable number assigned to a
wireless phone."
::= { c3gCdmaIdentityEntry 6 }
c3gMsid OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..64))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Mobile Station Identifier (MSID), MSID is utilized to
distinguish the mobile station being programmed from other
mobile stations during messaging and paging processes,
including the downloading of programming information to the
mobile station."
::= { c3gCdmaIdentityEntry 7 }
c3gMsl OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..64))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Mobile Subscriber Lock (MSL)."
::= { c3gCdmaIdentityEntry 8 }
c3gCdmaNetworkTable OBJECT-TYPE
SYNTAX SEQUENCE OF C3gCdmaNetworkEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Cellular 3G CDMA network table."
::= { c3gWanCdma 4 }
c3gCdmaNetworkEntry OBJECT-TYPE
SYNTAX C3gCdmaNetworkEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (conceptual row) in the c3gCdmaNetworkTable."
INDEX { entPhysicalIndex }
::= { c3gCdmaNetworkTable 1 }
C3gCdmaNetworkEntry ::= SEQUENCE {
c3gCdmaCurrentServiceStatus DisplayString,
c3gCdmaHybridModePreference INTEGER,
c3gCdmaCurrentRoamingStatus INTEGER,
c3gCurrentIdleDigitalMode INTEGER,
c3gCurrentSid Integer32,
c3gCurrentNid Integer32,
c3gCurrentCallSetupMode INTEGER,
c3gSipUsername DisplayString,
c3gSipPassword DisplayString,
c3gServingBaseStationLongitude DisplayString,
c3gServingBaseStationLatitude DisplayString
}
c3gCdmaCurrentServiceStatus OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..64))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Current service status."
::= { c3gCdmaNetworkEntry 1 }
c3gCdmaHybridModePreference OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
hybrid(2),
evDoOnly(3),
oneXRttOnly(4)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object indicates the hybrid mode preference:
unknown(1) - preference unknown
hybrid(2) - connect to EV-DO/1xRTT services
evDoOnly(3) - connect to only EV-DO service
oneXRttOnly(4) - connect to only 1xRTT service"
DEFVAL { unknown }
::= { c3gCdmaNetworkEntry 2 }
c3gCdmaCurrentRoamingStatus OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
home(2),
roamingWithSid(3),
roamingWithoutSid(4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Current 1xRTT roaming status, roaming is a general term in
wireless telecommunications that refers to the extending of
connectivity service in a location that is different from the
home location where the service was registered:
unknown(1) - roaming status is unknown.
home(2) - connectivity service in home location.
roamingWithSid(3) - roaming with SID.
roamingWithoutSid(4) - roaming without SID"
DEFVAL { unknown }
::= { c3gCdmaNetworkEntry 3 }
c3gCurrentIdleDigitalMode OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
noService(2),
amps(3),
cdma(4),
gsm(5),
hdr(6),
wcdma(7),
gps(8),
lte(9)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Current idle digital mode:
unknown(1) - service is unknown
noService(2) - no service
amps(3) - Advanced Mobile Phone Service (AMPS)
cdma(4) - Code Division Multiple Access (CDMA)
gsm(5) - Global System for Mobile communications (GSM)
hdr(6) - High Data Rate (HDR)
wcdma(7) - Wideband Code-Division Multiple-Access (WCDMA)
gps(8) - Global Positioning System (GPS)
lte(9) - Long Term Evolution (LTE)"
DEFVAL { noService }
::= { c3gCdmaNetworkEntry 4 }
c3gCurrentSid OBJECT-TYPE
SYNTAX Integer32 (-1..32767)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Current System Identifier (SID), SID is a 15-bit numeric
identifiers used by cellular systems to identify the
home system of a cellular telephone and by the cellular
telephone to determine its roaming status. Value of '-1'
indicates SID is 'Not Applicable'."
::= { c3gCdmaNetworkEntry 5 }
c3gCurrentNid OBJECT-TYPE
SYNTAX Integer32 (-1..65535)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Current Network Identification (NID), NID is a 16-bit numeric
identifiers used by cellular systems. Value of '-1' indicates
NID is 'Not Applicable'."
::= { c3gCdmaNetworkEntry 6 }
c3gCurrentCallSetupMode OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
simpleIpOnly(2),
mobileIpPreferWithSipFallback(3),
mobileIpOnly(4)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Current call setup mode. The 1xEV-DO system supports packet
data connections to a public or private data network using
either mobile IP or simple IP protocol. For simple IP
protocol, moving from the coverage area of one PDSN to another
PDSN constitutes a change in packet data session. For mobile
IP protocol, a packet data session can span several PDSNs as
long as the user continuously maintains mobility bindings at
the Home Agent (the IP address is persistent). The modes are:
unknown(1) - mode is unknown
simpleIpOnly(2) - simple IP only
mobileIpPreferWithSipFallback(3) - prefer mobile IP with
simple IP as fallback mode
mobileIpOnly(4) - mobile IP only"
DEFVAL { unknown }
::= { c3gCdmaNetworkEntry 7 }
c3gSipUsername OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..64))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Simple IP (SIP) user name."
::= { c3gCdmaNetworkEntry 8 }
c3gSipPassword OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..64))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Simple IP (SIP) password."
::= { c3gCdmaNetworkEntry 9 }
c3gServingBaseStationLongitude OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..64))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Longitude of the serving base station."
::= { c3gCdmaNetworkEntry 10 }
c3gServingBaseStationLatitude OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..64))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Latitude of the serving base station."
::= { c3gCdmaNetworkEntry 11 }
c3gCdmaProfile OBJECT IDENTIFIER
::= { c3gWanCdma 5 }
c3gCdmaProfileCommonTable OBJECT-TYPE
SYNTAX SEQUENCE OF C3gCdmaProfileCommonEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Cellular 3G CDMA profile common table."
::= { c3gCdmaProfile 1 }
c3gCdmaProfileCommonEntry OBJECT-TYPE
SYNTAX C3gCdmaProfileCommonEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (conceptual row) in the c3gCdmaProfileCommonTable."
INDEX { entPhysicalIndex }
::= { c3gCdmaProfileCommonTable 1 }
C3gCdmaProfileCommonEntry ::= SEQUENCE {
c3gNumberOfDataProfileConfigurable Unsigned32,
c3gCurrentActiveDataProfile Unsigned32
}
c3gNumberOfDataProfileConfigurable OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The number of data profiles configurable."
DEFVAL { 0 }
::= { c3gCdmaProfileCommonEntry 1 }
c3gCurrentActiveDataProfile OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The current active data profile."
::= { c3gCdmaProfileCommonEntry 2 }
c3gCdmaProfileTable OBJECT-TYPE
SYNTAX SEQUENCE OF C3gCdmaProfileEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Cellular 3G CDMA profile table."
::= { c3gCdmaProfile 2 }
c3gCdmaProfileEntry OBJECT-TYPE
SYNTAX C3gCdmaProfileEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (conceptual row) in the c3gCdmaProfileTable."
INDEX {
entPhysicalIndex,
c3gCdmaProfileIndex
}
::= { c3gCdmaProfileTable 1 }
C3gCdmaProfileEntry ::= SEQUENCE {
c3gCdmaProfileIndex Integer32,
c3gNai DisplayString,
c3gAaaPassword DisplayString,
c3gMnHaSs INTEGER,
c3gMnHaSpi Unsigned32,
c3gMnAaaSs INTEGER,
c3gMnAaaSpi Unsigned32,
c3gReverseTunnelPreference INTEGER,
c3gHomeAddrType InetAddressType,
c3gHomeAddr InetAddress,
c3gPriHaAddrType InetAddressType,
c3gPriHaAddr InetAddress,
c3gSecHaAddrType InetAddressType,
c3gSecHaAddr InetAddress
}
c3gCdmaProfileIndex OBJECT-TYPE
SYNTAX Integer32 (1..65535)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Profile index, combined with entPhysicalIndex to access
the profile table c3gCdmaProfileTable."
::= { c3gCdmaProfileEntry 1 }
c3gNai OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..64))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Network Access Identifier (NAI). NAI is required to identify
the mobile user and the network the mobile user intended to
access. The NAI is provided by the mobile node to the dialed
ISP during PPP authentication."
::= { c3gCdmaProfileEntry 2 }
c3gAaaPassword OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..64))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object indicates the password for AAA."
::= { c3gCdmaProfileEntry 3 }
c3gMnHaSs OBJECT-TYPE
SYNTAX INTEGER {
set(1),
notSet(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Mobile Node (MN) Home Agent (HA) Shared Secret (SS) setting:
set(1) - shared secret is set
notSet(2) - shared secret is not set"
DEFVAL { notSet }
::= { c3gCdmaProfileEntry 4 }
c3gMnHaSpi OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Mobile Node (MN) Home Agent (HA) Security Parameter Index
(SPI)."
::= { c3gCdmaProfileEntry 5 }
c3gMnAaaSs OBJECT-TYPE
SYNTAX INTEGER {
set(1),
notSet(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Mobile Node (MN) Authentication Authorization Accounting (AAA)
Shared Secret (SS) setting:
set(1) - shared secret is set
notSet(2) - shared secret is not set"
DEFVAL { notSet }
::= { c3gCdmaProfileEntry 6 }
c3gMnAaaSpi OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Mobile Node (MN) Authentication Authorization Accounting (AAA)
Security Parameter Index (SPI)."
::= { c3gCdmaProfileEntry 7 }
c3gReverseTunnelPreference OBJECT-TYPE
SYNTAX INTEGER {
set(1),
notSet(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Reverse tunnel preference."
::= { c3gCdmaProfileEntry 8 }
c3gHomeAddrType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"A value that represents the type of the IP Address stored in
the object c3gHomeAddr."
::= { c3gCdmaProfileEntry 9 }
c3gHomeAddr OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"A unicast routable address assigned to a Mobile Node, used as
the permanent address of the Mobile Node."
::= { c3gCdmaProfileEntry 10 }
c3gPriHaAddrType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"A value that represents the type of the IP Address stored in
the object c3gPriHaAddr."
::= { c3gCdmaProfileEntry 11 }
c3gPriHaAddr OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The primary home agent address."
::= { c3gCdmaProfileEntry 12 }
c3gSecHaAddrType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"A value that represents the type of the IP Address stored in
the object c3gSecHaAddr."
::= { c3gCdmaProfileEntry 13 }
c3gSecHaAddr OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The secondary home agent address."
::= { c3gCdmaProfileEntry 14 }
c3gCdmaRadio OBJECT IDENTIFIER
::= { c3gWanCdma 6 }
c3gCdma1xRttRadioTable OBJECT-TYPE
SYNTAX SEQUENCE OF C3gCdma1xRttRadioEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Cellular 3G CDMA 1xRTT radio table."
::= { c3gCdmaRadio 1 }
c3gCdma1xRttRadioEntry OBJECT-TYPE
SYNTAX C3gCdma1xRttRadioEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (conceptual row) in the c3gCdma1xRttRadioTable."
INDEX { entPhysicalIndex }
::= { c3gCdma1xRttRadioTable 1 }
C3gCdma1xRttRadioEntry ::= SEQUENCE {
c3gCurrent1xRttRssi C3gRssi,
c3gCurrent1xRttEcIo C3gEcIo,
c3gCurrent1xRttChannelNumber Integer32,
c3gCurrent1xRttChannelState INTEGER
}
c3gCurrent1xRttRssi OBJECT-TYPE
SYNTAX C3gRssi
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Current 1xRTT RSSI value."
::= { c3gCdma1xRttRadioEntry 1 }
c3gCurrent1xRttEcIo OBJECT-TYPE
SYNTAX C3gEcIo
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Current 1xRTT Ec/Io value."
::= { c3gCdma1xRttRadioEntry 2 }
c3gCurrent1xRttChannelNumber OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Current 1xRTT channel number. Current channel number to which
the modem is attached to the base station. Value of '-1'
indicates 'No Service'."
::= { c3gCdma1xRttRadioEntry 3 }
c3gCurrent1xRttChannelState OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
notAcquired(2),
acquired(3),
scanning(4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Current 1xRTT channel state. Indicates whether the modem is
scanning or has acquired the channel."
DEFVAL { notAcquired }
::= { c3gCdma1xRttRadioEntry 4 }
c3gCdma1xRttBandClassTable OBJECT-TYPE
SYNTAX SEQUENCE OF C3gCdma1xRttBandClassEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Cellular 3G CDMA 1xRTT band class table. This table contains
band class information for each available band."
::= { c3gCdmaRadio 2 }
c3gCdma1xRttBandClassEntry OBJECT-TYPE
SYNTAX C3gCdma1xRttBandClassEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (conceptual row) in the c3gCdma1xRttBandClassTable."
INDEX {
entPhysicalIndex,
c3gBandClassIndex
}
::= { c3gCdma1xRttBandClassTable 1 }
C3gCdma1xRttBandClassEntry ::= SEQUENCE {
c3gBandClassIndex Integer32,
c3g1xRttBandClass Unsigned32
}
c3gBandClassIndex OBJECT-TYPE
SYNTAX Integer32 (1..32)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Band class index, combined with entPhysicalIndex to access
the band class table."
::= { c3gCdma1xRttBandClassEntry 1 }
c3g1xRttBandClass OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains 1xRTT band class."
::= { c3gCdma1xRttBandClassEntry 2 }
c3gCdmaEvDoRadioTable OBJECT-TYPE
SYNTAX SEQUENCE OF C3gCdmaEvDoRadioEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Cellular 3G CDMA EV-DO radio table."
::= { c3gCdmaRadio 3 }
c3gCdmaEvDoRadioEntry OBJECT-TYPE
SYNTAX C3gCdmaEvDoRadioEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (conceptual row) in the c3gCdmaEvDoRadioTable."
INDEX { entPhysicalIndex }
::= { c3gCdmaEvDoRadioTable 1 }
C3gCdmaEvDoRadioEntry ::= SEQUENCE {
c3gCurrentEvDoRssi C3gRssi,
c3gCurrentEvDoEcIo C3gEcIo,
c3gCurrentEvDoChannelNumber Integer32,
c3gSectorId DisplayString,
c3gSubnetMask Unsigned32,
c3gHdrColorCode Unsigned32,
c3gPnOffset Unsigned32,
c3gRxMainGainControl Integer32,
c3gRxDiversityGainControl Integer32,
c3gTxTotalPower Integer32,
c3gTxGainAdjust Integer32,
c3gCarrierToInterferenceRatio Unsigned32
}
c3gCurrentEvDoRssi OBJECT-TYPE
SYNTAX C3gRssi
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Current EV-DO RSSI value."
::= { c3gCdmaEvDoRadioEntry 1 }
c3gCurrentEvDoEcIo OBJECT-TYPE
SYNTAX C3gEcIo
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Current EV-DO Ec/Io value."
::= { c3gCdmaEvDoRadioEntry 2 }
c3gCurrentEvDoChannelNumber OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Current EV-DO channel number. Current channel number to
which the modem is attached to the base station. Value of '-1'
indicates 'No Service'."
::= { c3gCdmaEvDoRadioEntry 3 }
c3gSectorId OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..64))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Sector ID of the base station to which the modem is attached."
::= { c3gCdmaEvDoRadioEntry 4 }
c3gSubnetMask OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Subnet mask of the sector, not to be confused with the IP
subnet mask."
REFERENCE "3GPP2 C.S0024-B v1.0"
::= { c3gCdmaEvDoRadioEntry 5 }
c3gHdrColorCode OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Color code of the sector."
REFERENCE "3GPP2 C.S0024-B v1.0"
::= { c3gCdmaEvDoRadioEntry 6 }
c3gPnOffset OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"PN offset. PN offset is a time offset from the beginning of
the well-known pseudo-random noise sequence that is used to
spread the signal from the base station."
REFERENCE "3GPP2 C.S0024-B v1.0"
::= { c3gCdmaEvDoRadioEntry 7 }
c3gRxMainGainControl OBJECT-TYPE
SYNTAX Integer32
UNITS "dBm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Received main gain control for the modem. value of '-1'
indicates the received main gain control is unavailable."
::= { c3gCdmaEvDoRadioEntry 8 }
c3gRxDiversityGainControl OBJECT-TYPE
SYNTAX Integer32
UNITS "dBm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Received diversity for the modem. value of '-1' indicates the
received diversity is unavailable."
::= { c3gCdmaEvDoRadioEntry 9 }
c3gTxTotalPower OBJECT-TYPE
SYNTAX Integer32
UNITS "dBm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Transmit total power."
::= { c3gCdmaEvDoRadioEntry 10 }
c3gTxGainAdjust OBJECT-TYPE
SYNTAX Integer32
UNITS "dBm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Transmit gain adjust."
::= { c3gCdmaEvDoRadioEntry 11 }
c3gCarrierToInterferenceRatio OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Carrier to interference ratio. Carrier-to-Interference
ratio (C/I) is the ratio of power in an RF carrier to the
interference power in the channel."
::= { c3gCdmaEvDoRadioEntry 12 }
c3gCdmaEvDoBandClassTable OBJECT-TYPE
SYNTAX SEQUENCE OF C3gCdmaEvDoBandClassEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Cellular 3G CDMA EV-DO band class table. This table contains
band class information for each available band."
::= { c3gCdmaRadio 4 }
c3gCdmaEvDoBandClassEntry OBJECT-TYPE
SYNTAX C3gCdmaEvDoBandClassEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (conceptual row) in the c3gCdmaEvDoBandClassTable."
INDEX {
entPhysicalIndex,
c3gBandClassIndex
}
::= { c3gCdmaEvDoBandClassTable 1 }
C3gCdmaEvDoBandClassEntry ::= SEQUENCE {
c3gEvDoBandClass Unsigned32
}
c3gEvDoBandClass OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains EV-DO band class."
::= { c3gCdmaEvDoBandClassEntry 1 }
c3gCdmaHistoryTable OBJECT-TYPE
SYNTAX SEQUENCE OF C3gCdmaHistoryEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Cellular 3G CDMA history table. The history of RSSI are
carried in an octet of string. Each octet in the octet string
has a value from 0 to 150 and the 255 value is reserved to
indicate an uninitialized (Invalid) value. The format of the
octet string with n octets is as following:
[ octet 0 is latest,
octet 1 is latest-1,
.
.
octet n-2 is oldest-1,
octet n-1 is oldest ]
To convert the provided value into dBm the following formula
should be used:
dBm = (-1)*value;"
::= { c3gCdmaRadio 5 }
c3gCdmaHistoryEntry OBJECT-TYPE
SYNTAX C3gCdmaHistoryEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (conceptual row) in the c3gCdmaHistoryTable."
INDEX { entPhysicalIndex }
::= { c3gCdmaHistoryTable 1 }
C3gCdmaHistoryEntry ::= SEQUENCE {
c3gCdmaHistory1xRttRssiPerSecond OCTET STRING,
c3gCdmaHistory1xRttRssiPerMinute OCTET STRING,
c3gCdmaHistory1xRttRssiPerHour OCTET STRING,
c3gCdmaHistoryEvDoRssiPerSecond OCTET STRING,
c3gCdmaHistoryEvDoRssiPerMinute OCTET STRING,
c3gCdmaHistoryEvDoRssiPerHour OCTET STRING
}
c3gCdmaHistory1xRttRssiPerSecond OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (60))
UNITS "-dBm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Per-second 1xRTT RSSI history. This object contains a
per-second history of 1xRTT RSSI values for the last 60
seconds."
::= { c3gCdmaHistoryEntry 1 }
c3gCdmaHistory1xRttRssiPerMinute OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (60))
UNITS "-dBm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Per-minute 1xRTT weakest RSSI value history. This
object contains a per-minute history of 1xRTT weakest RSSI
values for the last 60 minutes. The octet in the string
is the weakest RSSI value measured in a minute interval."
::= { c3gCdmaHistoryEntry 2 }
c3gCdmaHistory1xRttRssiPerHour OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (72))
UNITS "-dBm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Per-hour 1xRTT weakest RSSI value history. This object
contains a per-hour history of 1xRTT weakest RSSI values for the
last 72 hours. The octet in the string is the weakest RSSI
value measured in an hour interval."
::= { c3gCdmaHistoryEntry 3 }
c3gCdmaHistoryEvDoRssiPerSecond OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (60))
UNITS "-dBm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Per-second EV-DO RSSI history. This object contains a
per-second history of EV-DO RSSI values for the last 60
seconds."
::= { c3gCdmaHistoryEntry 4 }
c3gCdmaHistoryEvDoRssiPerMinute OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (60))
UNITS "-dBm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Per-minute EV-DO weakest RSSI value history. This
object contains a per-minute history of EV-DO weakest RSSI
values for the last 60 minutes. The octet in the string is the
weakest RSSI value measured in a minute interval."
::= { c3gCdmaHistoryEntry 5 }
c3gCdmaHistoryEvDoRssiPerHour OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (72))
UNITS "-dBm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Per-hour EV-DO weakest RSSI value history. This object
contains a per-hour history of EV-DO weakest RSSI values for the
last 72 hours. The octet in the string is the weakest RSSI
value measured in an hour interval."
::= { c3gCdmaHistoryEntry 6 }
c3gCdmaSecurity OBJECT IDENTIFIER
::= { c3gWanCdma 7 }
c3gCdmaSecurityTable OBJECT-TYPE
SYNTAX SEQUENCE OF C3gCdmaSecurityEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Cellular 3G CDMA security table."
::= { c3gCdmaSecurity 1 }
c3gCdmaSecurityEntry OBJECT-TYPE
SYNTAX C3gCdmaSecurityEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (conceptual row) in the c3gCdmaSecurityTable."
INDEX { entPhysicalIndex }
::= { c3gCdmaSecurityTable 1 }
C3gCdmaSecurityEntry ::= SEQUENCE {
c3gCdmaPinSecurityStatus INTEGER,
c3gCdmaPowerUpLockStatus INTEGER
}
c3gCdmaPinSecurityStatus OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
locked(2),
unlocked(3)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"CDMA Personal Identification Number (PIN) security:
unknown(1) - PIN security unknown
locked(2) - PIN security is locked
unlocked(3) - PIN security is unlocked"
DEFVAL { unlocked }
::= { c3gCdmaSecurityEntry 1 }
c3gCdmaPowerUpLockStatus OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
enabled(2),
disabled(3)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"CDMA power up lock:
unknown(1) - power up lock unknown
enabled(2) - power up lock enabled
disabled(3) - power up lock disabled"
DEFVAL { disabled }
::= { c3gCdmaSecurityEntry 2 }
c3gGsmIdentityTable OBJECT-TYPE
SYNTAX SEQUENCE OF C3gGsmIdentityEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"."
::= { c3gWanGsm 1 }
c3gGsmIdentityEntry OBJECT-TYPE
SYNTAX C3gGsmIdentityEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (conceptual row) in the c3gGsmIdentityTable."
INDEX { entPhysicalIndex }
::= { c3gGsmIdentityTable 1 }
C3gGsmIdentityEntry ::= SEQUENCE {
c3gImsi DisplayString,
c3gImei DisplayString,
c3gIccId DisplayString,
c3gMsisdn DisplayString,
c3gFsn DisplayString,
c3gModemStatus INTEGER,
c3gGsmRoamingPreference INTEGER
}
c3gImsi OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..64))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"International Mobile Subscriber Identifier (IMSI), a unique
15-digit code used to identify an individual user on a GSM/LTE
network."
::= { c3gGsmIdentityEntry 1 }
c3gImei OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..64))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"International Mobile Equipment Identifier (IMEI), a unique 15
or 17 digit code used to identify an individual mobile station
to a GSM, UMTS or LTE network."
::= { c3gGsmIdentityEntry 2 }
c3gIccId OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..64))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the Integrated Circuit Card ID (ICCID).
The ICCID is defined by the ITU-T recommendation E.118.
ICCIDs are stored in the SIM cards and are also engraved or
printed on the SIM card body during a process called
personalization."
::= { c3gGsmIdentityEntry 3 }
c3gMsisdn OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..64))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object indicates the Mobile Subscriber Integrated Services
Digital Network Number (MSISDN). It is a number uniquely
identifying a subscription in a GSM, UMTS or LTE mobile
network. It represents the telephone number to the SIM
card in a mobile/cellular phone."
::= { c3gGsmIdentityEntry 4 }
c3gFsn OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..64))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Forward Sequence Number (FSN), a message acknowledgement
method using sequence number in the forward direction."
::= { c3gGsmIdentityEntry 5 }
c3gModemStatus OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
offLine(2),
onLine(3),
lowPowerMode(4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Modem status:
unknown(1) - modem status is unknown
offLine(2) - modem is off line
onLine(3) - modem is on line
lowPowerMode(4) - modem is in the low power mode"
DEFVAL { unknown }
::= { c3gGsmIdentityEntry 6 }
c3gGsmRoamingPreference OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
home(2),
roaming(3)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object indicates the roaming preference."
::= { c3gGsmIdentityEntry 7 }
c3gGsmNetworkTable OBJECT-TYPE
SYNTAX SEQUENCE OF C3gGsmNetworkEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Cellular GSM Network table. This table is applicable in both
3G and 4G-LTE technology mode"
::= { c3gWanGsm 2 }
c3gGsmNetworkEntry OBJECT-TYPE
SYNTAX C3gGsmNetworkEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (conceptual row) in the c3gGsmNetworkTable."
INDEX { entPhysicalIndex }
::= { c3gGsmNetworkTable 1 }
C3gGsmNetworkEntry ::= SEQUENCE {
c3gGsmLac Unsigned32,
c3gGsmCurrentServiceStatus INTEGER,
c3gGsmCurrentServiceError INTEGER,
c3gGsmCurrentService INTEGER,
c3gGsmPacketService INTEGER,
c3gGsmCurrentRoamingStatus INTEGER,
c3gGsmNetworkSelectionMode INTEGER,
c3gGsmCountry DisplayString,
c3gGsmNetwork DisplayString,
c3gGsmMcc Integer32,
c3gGsmMnc Integer32,
c3gGsmRac Unsigned32,
c3gGsmCurrentCellId Unsigned32,
c3gGsmCurrentPrimaryScramblingCode Unsigned32,
c3gGsmPlmnSelection INTEGER,
c3gGsmRegPlmn DisplayString,
c3gGsmPlmnAbbr DisplayString,
c3gGsmServiceProvider DisplayString,
c3gGsmTotalByteTransmitted Counter64,
c3gGsmTotalByteReceived Counter64
}
c3gGsmLac OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Location Area Code (LAC), also called as Tracking
Area Code (TAC) in LTE standard. LAC/TAC is given
by the base station."
DEFVAL { 0 }
::= { c3gGsmNetworkEntry 1 }
c3gGsmCurrentServiceStatus OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
noService(2),
normal(3),
emergencyOnly(4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Current Service Status:
unknown(1) - current service status is unknown
noService(2) - no service
normal(3) - service status is normal
emergencyOnly(4) - emergency service only"
DEFVAL { unknown }
::= { c3gGsmNetworkEntry 2 }
c3gGsmCurrentServiceError OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
none(2),
imsiUnknownInHlr(3),
illegalMs(4),
imsiUnknownInVlr(5),
imeiNotAccepted(6),
illegalMe(7),
gprsServNotAllowed(8),
gprsNonGprsServNotAllow(9),
msIdentUnknown(10),
implicitlyDetached(11),
plmnNotAllowed(12),
lacNotAllowed(13),
roamingNotAllowed(14),
gprsServNotAllowInPlmn(15),
noSuitableCellInLa(16),
mscTempNotReachable(17),
networkFailure(18),
macFailure(19),
synchFailure(20),
congestion(21),
gsmAuthenNotAccept(22),
servOptionNotSupport(23),
reqServOptionNotSub(24),
servOptionOutOfOrder(25),
callCannotIdentified(26),
noPdpContextActivated(27),
invalidMandatInfo(28),
unpsecProtErr(29)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Current service error:
unknown(1) - Unknown
none(2) - None
imsiUnknownInHlr(3) - IMSI unknown in HLR (Home
Location Register)
illegalMs(4) - Illegal MS (Mobile Station)
imsiUnknownInVlr(5) - IMSI unknown in VLR (Visitor
Location Register)
imeiNotAccepted(6) - IMEI not accepted
illegalMe(7) - Illegal ME (Mobile Entity)
gprsServNotAllowed(8) - GPRS services not allowed
gprsNonGprsServNotAllow(9) - GPRS and non-GPRS services
not allowed
msIdentUnknown(10) - MS identity unknown
implicitlyDetached(11) - Implicitly detached
plmnNotAllowed(12) - PLMN not allowed
lacNotAllowed(13) - LAC not allowed
roamingNotAllowed(14) - Roaming not allowed
gprsServNotAllowInPlmn(15) - GPRS services not allowed
in this PLMN
noSuitableCellInLa(16) - No suitable cells in LA (Location
Area)
mscTempNotReachable(17) - MSC (Mobile Switching Center)
temporarily not reachable
networkFailure(18) - Network failure
macFailure(19) - MAC failure
synchFailure(20) - Synch failure
congestion(21) - Congestion
gsmAuthenNotAccept(22) - GSM/LTE Authentication not accepted
servOptionNotSupport(23) - Service option not supported
reqServOptionNotSub(24) - Requested service option not
subscribed
servOptionOutOfOrder(25) - Service option out of order
callCannotIdentified(26) - Call cannot be identified
noPdpContextActivated(27) - No PDP context activated
invalidMandatInfo(28) - Invalid mandatory info
unpsecProtErr(29) - Unspecified protocol error"
::= { c3gGsmNetworkEntry 3 }
c3gGsmCurrentService OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
invalid(2),
circuitSwitched(3),
packetSwitched(4),
combined(5)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Current service type:
unknown(1) - service type is unknown
invalid(2) - no service
circuitSwitched(3) - circuit switched service
packetSwitched(4) - packet switched service
combined(5) - combination of circuit and packet
switched service"
DEFVAL { unknown }
::= { c3gGsmNetworkEntry 4 }
c3gGsmPacketService OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
none(2),
gprs(3),
edge(4),
umtsWcdma(5),
hsdpa(6),
hsupa(7),
hspa(8),
hspaPlus(9),
lte(10)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Packet Service type:
unknown(1) - service type is unknown.
none(2) - no service.
gprs(3) - General Packet Radio Service (GPRS).
edge(4) - Enhanced Data rates for GSM Evolution (EDGE).
umtsWcdma(5) - Universal Mobile Telecommunications
System (UMTS) / Wideband Code-Division
Multiple-Access (W-CDMA).
hsdpa(6) - High-Speed Downlink Packet Access (HSDPA)
hsdpa(7) - High-Speed Uplink Packet Access (HSUPA)
hspa(8) - High-Speed Packet Access (HSPA)
hspaPlus(9) - High-Speed Packet Access (HSPA) Plus
lte(10) - Long Term Evolution"
DEFVAL { unknown }
::= { c3gGsmNetworkEntry 5 }
c3gGsmCurrentRoamingStatus OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
roaming(2),
home(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates whether the modem is in the home network
or is roaming."
DEFVAL { home }
::= { c3gGsmNetworkEntry 6 }
c3gGsmNetworkSelectionMode OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
automatic(2),
manual(3)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Network selection mode. Can be manual selection mode or
automatic selection mode. Set to automatic by default."
DEFVAL { automatic }
::= { c3gGsmNetworkEntry 7 }
c3gGsmCountry OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..64))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Country code. Country code string is given by the base
station."
::= { c3gGsmNetworkEntry 8 }
c3gGsmNetwork OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..64))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Network code. Network Code string is given by the base
station."
::= { c3gGsmNetworkEntry 9 }
c3gGsmMcc OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Mobile Country Code (MCC). Value of '-1' indicates MCC is 'Not
Applicable'."
DEFVAL { 0 }
::= { c3gGsmNetworkEntry 10 }
c3gGsmMnc OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Mobile Network Code (MNC). Value of '-1' indicates MNC is 'Not
Applicable'."
DEFVAL { 0 }
::= { c3gGsmNetworkEntry 11 }
c3gGsmRac OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Routing Area Code (RAC). RAC is given by the base station."
DEFVAL { 0 }
::= { c3gGsmNetworkEntry 12 }
c3gGsmCurrentCellId OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Cell Identifier of current cell. Cell ID is given by the
base station."
DEFVAL { 0 }
::= { c3gGsmNetworkEntry 13 }
c3gGsmCurrentPrimaryScramblingCode OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Primary scrambling code of current cell. The primary
scrambling code is typically identified through
symbol-by-symbol correlation over the CPICH (Common Pilot
Channel) with all codes within the code group, after the
primary scrambling code has been identified,
the Primary CCPCH can be detected and the system and cell
specific BCH information can be read."
DEFVAL { 0 }
::= { c3gGsmNetworkEntry 14 }
c3gGsmPlmnSelection OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
manual(2),
automatic(3)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Public Land Mobile Network (PLMN) selection. Can be manual
selection mode or automatic selection mode. Set to automatic by
default."
DEFVAL { automatic }
::= { c3gGsmNetworkEntry 15 }
c3gGsmRegPlmn OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..64))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Registered PLMN."
::= { c3gGsmNetworkEntry 16 }
c3gGsmPlmnAbbr OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..64))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"PLMN abbreviated number."
::= { c3gGsmNetworkEntry 17 }
c3gGsmServiceProvider OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..64))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Service provider."
::= { c3gGsmNetworkEntry 18 }
c3gGsmTotalByteTransmitted OBJECT-TYPE
SYNTAX Counter64
UNITS "bytes"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of bytes transmitted for all calls. It is the
total number of bytes transmitted by modem, not to be confused
with the number of bytes transmitted through the interface."
::= { c3gGsmNetworkEntry 19 }
c3gGsmTotalByteReceived OBJECT-TYPE
SYNTAX Counter64
UNITS "bytes"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of bytes received for all calls. It is the total
number of bytes received by modem, not to be confused with the
number of bytes received from the interface."
::= { c3gGsmNetworkEntry 20 }
c3gGsmPdpProfile OBJECT IDENTIFIER
::= { c3gWanGsm 3 }
c3gGsmPdpProfileTable OBJECT-TYPE
SYNTAX SEQUENCE OF C3gGsmPdpProfileEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Cellular GSM PDP profiles table. Cellular device contains
multiple profile entries which can be used to establish
cellular data connections (PDP contexts). Users can choose
any of available PDP profiles to establish data connections.
Data connections are described in c3gGsmPacketSessionTable.
This table is applicable in only 3G technology mode. Refer
CISCO-WAN-CELL-EXT-MIB when in 4G-LTE mode."
::= { c3gGsmPdpProfile 1 }
c3gGsmPdpProfileEntry OBJECT-TYPE
SYNTAX C3gGsmPdpProfileEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (conceptual row) in the c3gGsmPdpProfileTable."
INDEX {
entPhysicalIndex,
c3gGsmPdpProfileIndex
}
::= { c3gGsmPdpProfileTable 1 }
C3gGsmPdpProfileEntry ::= SEQUENCE {
c3gGsmPdpProfileIndex Integer32,
c3gGsmPdpProfileType C3gPdpType,
c3gGsmPdpProfileAddr DisplayString,
c3gGsmPdpProfileApn DisplayString,
c3gGsmPdpProfileAuthenType INTEGER,
c3gGsmPdpProfileUsername DisplayString,
c3gGsmPdpProfilePassword DisplayString,
c3gGsmPdpProfileRowStatus RowStatus
}
c3gGsmPdpProfileIndex OBJECT-TYPE
SYNTAX Integer32 (1..1000)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Profile index, combined with entPhysicalIndex to
access profile table."
::= { c3gGsmPdpProfileEntry 1 }
c3gGsmPdpProfileType OBJECT-TYPE
SYNTAX C3gPdpType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object indicates configured Packet Data Protocol (PDP)
type."
DEFVAL { unknown }
::= { c3gGsmPdpProfileEntry 2 }
c3gGsmPdpProfileAddr OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..64))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Configured PDP/EPS Bearer address. PDP type is
defined in c3gGsmPdpProfileType."
::= { c3gGsmPdpProfileEntry 3 }
c3gGsmPdpProfileApn OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..64))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object indicates profile Access Point Name (APN). This
information is provided by the service provider."
::= { c3gGsmPdpProfileEntry 4 }
c3gGsmPdpProfileAuthenType OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
none(2),
chap(3),
pap(4)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object indicates PDP authentication type
supported. CHAP and PAP are supported in GSM. The type of
authentication to be used is provided by the service
provider."
DEFVAL { unknown }
::= { c3gGsmPdpProfileEntry 5 }
c3gGsmPdpProfileUsername OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..64))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object indicates the username to be used for PDP
authentication. This information is provided by the service
provider."
::= { c3gGsmPdpProfileEntry 6 }
c3gGsmPdpProfilePassword OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..64))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object indicates the password to be used for PDP
authentication. This information is provided by the service
provider."
::= { c3gGsmPdpProfileEntry 7 }
c3gGsmPdpProfileRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The status of this conceptual row. This object is used to
manage creation, modification and deletion of rows in this
table."
::= { c3gGsmPdpProfileEntry 8 }
c3gGsmPacketSessionTable OBJECT-TYPE
SYNTAX SEQUENCE OF C3gGsmPacketSessionEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Cellular 3G GSM packet session table. This table is applicable
in only 3G technology mode. Refer CISCO-WAN-CELL-EXT-MIB
when in 4G-LTE mode."
::= { c3gGsmPdpProfile 2 }
c3gGsmPacketSessionEntry OBJECT-TYPE
SYNTAX C3gGsmPacketSessionEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (conceptual row) in the c3gGsmPacketSessionTable."
INDEX {
entPhysicalIndex,
c3gGsmPdpProfileIndex
}
::= { c3gGsmPacketSessionTable 1 }
C3gGsmPacketSessionEntry ::= SEQUENCE {
c3gGsmPacketSessionStatus INTEGER,
c3gGsmPdpType C3gPdpType,
c3gGsmPdpAddress DisplayString
}
c3gGsmPacketSessionStatus OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
active(2),
inactive(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates PDP session status
of the profile. This is active when the call is established
and PDP contextr has become active."
DEFVAL { inactive }
::= { c3gGsmPacketSessionEntry 1 }
c3gGsmPdpType OBJECT-TYPE
SYNTAX C3gPdpType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates current session PDP type."
::= { c3gGsmPacketSessionEntry 2 }
c3gGsmPdpAddress OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..64))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Current session PDP context/EPS Bearer address. PDP type is
obtained from c3gGsmPdpType."
::= { c3gGsmPacketSessionEntry 3 }
c3gGsmReqUmtsQosTable OBJECT-TYPE
SYNTAX SEQUENCE OF C3gGsmReqUmtsQosEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Requested UMTS QoS parameters table. This table contains UMTS
QoS parameters requested by modem to the cellular network
via PDP Context Activation Request message. The requested UMTS
QoS profile is optional. This table is applicable only in 3G
technology mode."
::= { c3gGsmPdpProfile 3 }
c3gGsmReqUmtsQosEntry OBJECT-TYPE
SYNTAX C3gGsmReqUmtsQosEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (conceptual row) in the c3gGsmReqUmtsQosTable."
INDEX {
entPhysicalIndex,
c3gGsmPdpProfileIndex
}
::= { c3gGsmReqUmtsQosTable 1 }
C3gGsmReqUmtsQosEntry ::= SEQUENCE {
c3gGsmReqUmtsQosTrafficClass C3gUmtsQosTrafficClass,
c3gGsmReqUmtsQosMaxUpLinkBitRate C3gUmtsQosLinkBitRate,
c3gGsmReqUmtsQosMaxDownLinkBitRate C3gUmtsQosLinkBitRate,
c3gGsmReqUmtsQosGuaUpLinkBitRate C3gUmtsQosLinkBitRate,
c3gGsmReqUmtsQosGuaDownLinkBitRate C3gUmtsQosLinkBitRate,
c3gGsmReqUmtsQosOrder C3gUmtsQosOrder,
c3gGsmReqUmtsQosErroneousSdu C3gUmtsQosErroneousSdu,
c3gGsmReqUmtsQosMaxSduSize Unsigned32,
c3gGsmReqUmtsQosSer C3gUmtsQosSer,
c3gGsmReqUmtsQosBer C3gUmtsQosBer,
c3gGsmReqUmtsQosDelay Unsigned32,
c3gGsmReqUmtsQosPriority C3gUmtsQosPriority,
c3gGsmReqUmtsQosSrcStatDescriptor C3gUmtsQosSrcStatDescriptor,
c3gGsmReqUmtsQosSignalIndication C3gUmtsQosSignalIndication,
c3gGsmReqUmtsQosRowStatus RowStatus
}
c3gGsmReqUmtsQosTrafficClass OBJECT-TYPE
SYNTAX C3gUmtsQosTrafficClass
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Request UMTS QoS traffic classes."
::= { c3gGsmReqUmtsQosEntry 2 }
c3gGsmReqUmtsQosMaxUpLinkBitRate OBJECT-TYPE
SYNTAX C3gUmtsQosLinkBitRate
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Request UMTS QoS maximum uplink bit rate."
::= { c3gGsmReqUmtsQosEntry 3 }
c3gGsmReqUmtsQosMaxDownLinkBitRate OBJECT-TYPE
SYNTAX C3gUmtsQosLinkBitRate
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Request UMTS QoS maximum downlink bit rate."
::= { c3gGsmReqUmtsQosEntry 4 }
c3gGsmReqUmtsQosGuaUpLinkBitRate OBJECT-TYPE
SYNTAX C3gUmtsQosLinkBitRate
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Request UMTS QoS guaranteed uplink bit rate."
::= { c3gGsmReqUmtsQosEntry 5 }
c3gGsmReqUmtsQosGuaDownLinkBitRate OBJECT-TYPE
SYNTAX C3gUmtsQosLinkBitRate
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Request UMTS QoS guaranteed downlink bit rate."
::= { c3gGsmReqUmtsQosEntry 6 }
c3gGsmReqUmtsQosOrder OBJECT-TYPE
SYNTAX C3gUmtsQosOrder
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Request UMTS QoS deliver order."
::= { c3gGsmReqUmtsQosEntry 7 }
c3gGsmReqUmtsQosErroneousSdu OBJECT-TYPE
SYNTAX C3gUmtsQosErroneousSdu
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Request UMTS QoS Delivery of Erroneous SDU."
::= { c3gGsmReqUmtsQosEntry 8 }
c3gGsmReqUmtsQosMaxSduSize OBJECT-TYPE
SYNTAX Unsigned32 (0..1520)
UNITS "bytes"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Request UMTS QoS maximum SDU size, the valid range is between 1
and 1520 bytes. Value of '0' indicates the maximum SDU size is
unspecified."
::= { c3gGsmReqUmtsQosEntry 9 }
c3gGsmReqUmtsQosSer OBJECT-TYPE
SYNTAX C3gUmtsQosSer
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Request UMTS QoS SDU error ratio."
::= { c3gGsmReqUmtsQosEntry 10 }
c3gGsmReqUmtsQosBer OBJECT-TYPE
SYNTAX C3gUmtsQosBer
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Request UMTS QoS residual bit error ratio."
::= { c3gGsmReqUmtsQosEntry 11 }
c3gGsmReqUmtsQosDelay OBJECT-TYPE
SYNTAX Unsigned32 (0..4000)
UNITS "milliseconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Request UMTS QoS transfer delay in ms, the valid range
is between 1 and 4000 ms. Value of '0' indicates the
QoS delay is unspecified."
::= { c3gGsmReqUmtsQosEntry 12 }
c3gGsmReqUmtsQosPriority OBJECT-TYPE
SYNTAX C3gUmtsQosPriority
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Request UMTS QoS traffic handling priority."
::= { c3gGsmReqUmtsQosEntry 13 }
c3gGsmReqUmtsQosSrcStatDescriptor OBJECT-TYPE
SYNTAX C3gUmtsQosSrcStatDescriptor
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Request UMTS QoS source statistics descriptor."
::= { c3gGsmReqUmtsQosEntry 14 }
c3gGsmReqUmtsQosSignalIndication OBJECT-TYPE
SYNTAX C3gUmtsQosSignalIndication
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Request UMTS QoS signalling indication."
::= { c3gGsmReqUmtsQosEntry 15 }
c3gGsmReqUmtsQosRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The status of this conceptual row. This object is used to
manage creation, modification and deletion of rows in this
table."
::= { c3gGsmReqUmtsQosEntry 16 }
c3gGsmMinUmtsQosTable OBJECT-TYPE
SYNTAX SEQUENCE OF C3gGsmMinUmtsQosEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Minimum acceptable UMTS QoS table. This table contains minimum
acceptable UMTS QoS parameters which is checked by the MT
(Mobile Termination) against the negotiated profile returned in
the Activate PDP Context Accept message. The minimum acceptable
UMTS QoS profile is optional. This table is applicable only in
3G technology mode."
::= { c3gGsmPdpProfile 4 }
c3gGsmMinUmtsQosEntry OBJECT-TYPE
SYNTAX C3gGsmMinUmtsQosEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (conceptual row) in the c3gGsmMinUmtsQosTable."
INDEX {
entPhysicalIndex,
c3gGsmPdpProfileIndex
}
::= { c3gGsmMinUmtsQosTable 1 }
C3gGsmMinUmtsQosEntry ::= SEQUENCE {
c3gGsmMinUmtsQosTrafficClass C3gUmtsQosTrafficClass,
c3gGsmMinUmtsQosMaxUpLinkBitRate C3gUmtsQosLinkBitRate,
c3gGsmMinUmtsQosMaxDownLinkBitRate C3gUmtsQosLinkBitRate,
c3gGsmMinUmtsQosGuaUpLinkBitRate C3gUmtsQosLinkBitRate,
c3gGsmMinUmtsQosGuaDownLinkBitRate C3gUmtsQosLinkBitRate,
c3gGsmMinUmtsQosOrder C3gUmtsQosOrder,
c3gGsmMinUmtsQosErroneousSdu C3gUmtsQosErroneousSdu,
c3gGsmMinUmtsQosMaxSduSize Unsigned32,
c3gGsmMinUmtsQosSer C3gUmtsQosSer,
c3gGsmMinUmtsQosBer C3gUmtsQosBer,
c3gGsmMinUmtsQosDelay Unsigned32,
c3gGsmMinUmtsQosPriority C3gUmtsQosPriority,
c3gGsmMinUmtsQosSrcStatDescriptor C3gUmtsQosSrcStatDescriptor,
c3gGsmMinUmtsQosSignalIndication C3gUmtsQosSignalIndication,
c3gGsmMinUmtsQosRowStatus RowStatus
}
c3gGsmMinUmtsQosTrafficClass OBJECT-TYPE
SYNTAX C3gUmtsQosTrafficClass
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Minimum UMTS QoS traffic classes."
::= { c3gGsmMinUmtsQosEntry 1 }
c3gGsmMinUmtsQosMaxUpLinkBitRate OBJECT-TYPE
SYNTAX C3gUmtsQosLinkBitRate
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Minimum UMTS QoS maximum uplink bit rate."
::= { c3gGsmMinUmtsQosEntry 2 }
c3gGsmMinUmtsQosMaxDownLinkBitRate OBJECT-TYPE
SYNTAX C3gUmtsQosLinkBitRate
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Minimum UMTS QoS maximum downlink bit rate."
::= { c3gGsmMinUmtsQosEntry 3 }
c3gGsmMinUmtsQosGuaUpLinkBitRate OBJECT-TYPE
SYNTAX C3gUmtsQosLinkBitRate
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Minimum UMTS QoS guaranteed uplink bit rate."
::= { c3gGsmMinUmtsQosEntry 4 }
c3gGsmMinUmtsQosGuaDownLinkBitRate OBJECT-TYPE
SYNTAX C3gUmtsQosLinkBitRate
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Minimum UMTS QoS guaranteed downlink bit rate."
::= { c3gGsmMinUmtsQosEntry 5 }
c3gGsmMinUmtsQosOrder OBJECT-TYPE
SYNTAX C3gUmtsQosOrder
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Minimum UMTS QoS deliver order."
::= { c3gGsmMinUmtsQosEntry 6 }
c3gGsmMinUmtsQosErroneousSdu OBJECT-TYPE
SYNTAX C3gUmtsQosErroneousSdu
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Minimum UMTS QoS Delivery of Erroneous SDU."
::= { c3gGsmMinUmtsQosEntry 7 }
c3gGsmMinUmtsQosMaxSduSize OBJECT-TYPE
SYNTAX Unsigned32 (0..1520)
UNITS "bytes"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Minimum UMTS maximum SDU size, the valid range is between 1 and
1520 bytes. Value of '0' indicates the maximum SDU size is
unspecified."
::= { c3gGsmMinUmtsQosEntry 8 }
c3gGsmMinUmtsQosSer OBJECT-TYPE
SYNTAX C3gUmtsQosSer
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Minimum UMTS QoS SDU error ratio."
::= { c3gGsmMinUmtsQosEntry 9 }
c3gGsmMinUmtsQosBer OBJECT-TYPE
SYNTAX C3gUmtsQosBer
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Minimum UMTS residual bit error ratio."
::= { c3gGsmMinUmtsQosEntry 10 }
c3gGsmMinUmtsQosDelay OBJECT-TYPE
SYNTAX Unsigned32 (0..4000)
UNITS "milliseconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Minimum UMTS transfer delay in ms, the valid range
is between 1 and 4000 ms. Value of '0' indicates the
QoS delay is unspecified."
::= { c3gGsmMinUmtsQosEntry 11 }
c3gGsmMinUmtsQosPriority OBJECT-TYPE
SYNTAX C3gUmtsQosPriority
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Minimum UMTS QoS traffic handling priority."
::= { c3gGsmMinUmtsQosEntry 12 }
c3gGsmMinUmtsQosSrcStatDescriptor OBJECT-TYPE
SYNTAX C3gUmtsQosSrcStatDescriptor
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Minimum UMTS QoS source statistics descriptor."
::= { c3gGsmMinUmtsQosEntry 13 }
c3gGsmMinUmtsQosSignalIndication OBJECT-TYPE
SYNTAX C3gUmtsQosSignalIndication
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Minimum UMTS QoS signalling indication."
::= { c3gGsmMinUmtsQosEntry 14 }
c3gGsmMinUmtsQosRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The status of this conceptual row. This object is used to
manage creation, modification and deletion of rows in this
table."
::= { c3gGsmMinUmtsQosEntry 15 }
c3gGsmNegoUmtsQosTable OBJECT-TYPE
SYNTAX SEQUENCE OF C3gGsmNegoUmtsQosEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Negotiated UMTS QoS table. This table contains negotiated UMTS
QoS parameters returned in the Activate PDP Context Accept
message. The objects in this table are valid only if the value
of object c3gGsmPacketSessionStatus defined in
c3gGsmPacketSessionTable is 'active'. This table is applicable
only in 3G technology mode."
::= { c3gGsmPdpProfile 5 }
c3gGsmNegoUmtsQosEntry OBJECT-TYPE
SYNTAX C3gGsmNegoUmtsQosEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (conceptual row) in the c3gGsmNegoUmtsQosTable."
INDEX {
entPhysicalIndex,
c3gGsmPdpProfileIndex
}
::= { c3gGsmNegoUmtsQosTable 1 }
C3gGsmNegoUmtsQosEntry ::= SEQUENCE {
c3gGsmNegoUmtsQosTrafficClass C3gUmtsQosTrafficClass,
c3gGsmNegoUmtsQosMaxUpLinkBitRate C3gUmtsQosLinkBitRate,
c3gGsmNegoUmtsQosMaxDownLinkBitRate C3gUmtsQosLinkBitRate,
c3gGsmNegoUmtsQosGuaUpLinkBitRate C3gUmtsQosLinkBitRate,
c3gGsmNegoUmtsQosGuaDownLinkBitRate C3gUmtsQosLinkBitRate,
c3gGsmNegoUmtsQosOrder C3gUmtsQosOrder,
c3gGsmNegoUmtsQosErroneousSdu C3gUmtsQosErroneousSdu,
c3gGsmNegoUmtsQosMaxSduSize Unsigned32,
c3gGsmNegoUmtsQosSer C3gUmtsQosSer,
c3gGsmNegoUmtsQosBer C3gUmtsQosBer,
c3gGsmNegoUmtsQosDelay Unsigned32,
c3gGsmNegoUmtsQosPriority C3gUmtsQosPriority,
c3gGsmNegoUmtsQosSrcStatDescriptor C3gUmtsQosSrcStatDescriptor,
c3gGsmNegoUmtsQosSignalIndication C3gUmtsQosSignalIndication
}
c3gGsmNegoUmtsQosTrafficClass OBJECT-TYPE
SYNTAX C3gUmtsQosTrafficClass
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Negotiated UMTS QoS traffic classes."
::= { c3gGsmNegoUmtsQosEntry 1 }
c3gGsmNegoUmtsQosMaxUpLinkBitRate OBJECT-TYPE
SYNTAX C3gUmtsQosLinkBitRate
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Negotiated UMTS QoS maximum uplink bit rate."
::= { c3gGsmNegoUmtsQosEntry 2 }
c3gGsmNegoUmtsQosMaxDownLinkBitRate OBJECT-TYPE
SYNTAX C3gUmtsQosLinkBitRate
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Negotiated UMTS QoS maximum downlink bit rate."
::= { c3gGsmNegoUmtsQosEntry 3 }
c3gGsmNegoUmtsQosGuaUpLinkBitRate OBJECT-TYPE
SYNTAX C3gUmtsQosLinkBitRate
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Negotiated UMTS QoS guaranteed uplink bit rate."
::= { c3gGsmNegoUmtsQosEntry 4 }
c3gGsmNegoUmtsQosGuaDownLinkBitRate OBJECT-TYPE
SYNTAX C3gUmtsQosLinkBitRate
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Negotiated UMTS QoS guaranteed downlink bit rate."
::= { c3gGsmNegoUmtsQosEntry 5 }
c3gGsmNegoUmtsQosOrder OBJECT-TYPE
SYNTAX C3gUmtsQosOrder
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Negotiated UMTS QoS deliver order."
::= { c3gGsmNegoUmtsQosEntry 6 }
c3gGsmNegoUmtsQosErroneousSdu OBJECT-TYPE
SYNTAX C3gUmtsQosErroneousSdu
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Negotiated UMTS QoS Delivery of Erroneous SDU."
::= { c3gGsmNegoUmtsQosEntry 7 }
c3gGsmNegoUmtsQosMaxSduSize OBJECT-TYPE
SYNTAX Unsigned32 (0..1520)
UNITS "bytes"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Negotiated UMTS QoS maximum SDU size, the valid range is
between 1 and 1520 bytes. Value of '0' indicates the maximum
SDU size is subscribed."
::= { c3gGsmNegoUmtsQosEntry 8 }
c3gGsmNegoUmtsQosSer OBJECT-TYPE
SYNTAX C3gUmtsQosSer
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Negotiated UMTS QoS SDU error ratio."
::= { c3gGsmNegoUmtsQosEntry 9 }
c3gGsmNegoUmtsQosBer OBJECT-TYPE
SYNTAX C3gUmtsQosBer
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Negotiated UMTS QoS residual bit error ratio."
::= { c3gGsmNegoUmtsQosEntry 10 }
c3gGsmNegoUmtsQosDelay OBJECT-TYPE
SYNTAX Unsigned32 (0..4000)
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Negotiated UMTS QoS transfer delay in ms, the valid range
is between 1 and 4000 ms. Value of '0' indicates the
QoS delay is subscribed."
::= { c3gGsmNegoUmtsQosEntry 11 }
c3gGsmNegoUmtsQosPriority OBJECT-TYPE
SYNTAX C3gUmtsQosPriority
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Negotiated UMTS QoS traffic handling priority."
::= { c3gGsmNegoUmtsQosEntry 12 }
c3gGsmNegoUmtsQosSrcStatDescriptor OBJECT-TYPE
SYNTAX C3gUmtsQosSrcStatDescriptor
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Negotiated UMTS QoS source statistics descriptor."
::= { c3gGsmNegoUmtsQosEntry 13 }
c3gGsmNegoUmtsQosSignalIndication OBJECT-TYPE
SYNTAX C3gUmtsQosSignalIndication
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Negotiated UMTS QoS signalling indication."
::= { c3gGsmNegoUmtsQosEntry 14 }
c3gGsmReqGprsQosTable OBJECT-TYPE
SYNTAX SEQUENCE OF C3gGsmReqGprsQosEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Requested GPRS QoS parameters table. This table contains GPRS
QoS parameters requested by modem to the cellular network
via PDP Context Request message. The requested GPRS QoS
profile is optional. This table is applicable only in
3G technology mode."
::= { c3gGsmPdpProfile 6 }
c3gGsmReqGprsQosEntry OBJECT-TYPE
SYNTAX C3gGsmReqGprsQosEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (conceptual row) in the c3gGsmReqGprsQosTable."
INDEX {
entPhysicalIndex,
c3gGsmPdpProfileIndex
}
::= { c3gGsmReqGprsQosTable 1 }
C3gGsmReqGprsQosEntry ::= SEQUENCE {
c3gGsmReqGprsQosPrecedence C3gGprsQosPrecedence,
c3gGsmReqGprsQosDelay C3gGprsQosDelay,
c3gGsmReqGprsQosReliability C3gGprsQosReliability,
c3gGsmReqGprsQosPeakRate C3gGprsQosPeakRate,
c3gGsmReqGprsQosMeanRate C3gGprsQosMeanRate,
c3gGsmReqGprsQosRowStatus RowStatus
}
c3gGsmReqGprsQosPrecedence OBJECT-TYPE
SYNTAX C3gGprsQosPrecedence
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Request GPRS QoS precedence."
::= { c3gGsmReqGprsQosEntry 1 }
c3gGsmReqGprsQosDelay OBJECT-TYPE
SYNTAX C3gGprsQosDelay
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Request GPRS QoS delay classes."
::= { c3gGsmReqGprsQosEntry 2 }
c3gGsmReqGprsQosReliability OBJECT-TYPE
SYNTAX C3gGprsQosReliability
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Request GPRS QoS reliability."
::= { c3gGsmReqGprsQosEntry 3 }
c3gGsmReqGprsQosPeakRate OBJECT-TYPE
SYNTAX C3gGprsQosPeakRate
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Request GPRS QoS peak rate."
::= { c3gGsmReqGprsQosEntry 4 }
c3gGsmReqGprsQosMeanRate OBJECT-TYPE
SYNTAX C3gGprsQosMeanRate
UNITS "octet-per-hour"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Request GPRS QoS mean rate."
::= { c3gGsmReqGprsQosEntry 5 }
c3gGsmReqGprsQosRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The status of this conceptual row. This object is used to
manage creation, modification and deletion of rows in this
table."
::= { c3gGsmReqGprsQosEntry 6 }
c3gGsmMinGprsQosTable OBJECT-TYPE
SYNTAX SEQUENCE OF C3gGsmMinGprsQosEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Minimum acceptable GPRS QoS table. This table contains minimum
acceptable GPRS QoS parameters which is checked by the MT
(Mobile Termination) against the negotiated profile returned in
the Activate PDP Context Accept message. The minimum acceptable
GPRS QoS profile is optional. This table is applicable only in
3G technology mode."
::= { c3gGsmPdpProfile 7 }
c3gGsmMinGprsQosEntry OBJECT-TYPE
SYNTAX C3gGsmMinGprsQosEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (conceptual row) in the c3gGsmMinGprsQosTable."
INDEX {
entPhysicalIndex,
c3gGsmPdpProfileIndex
}
::= { c3gGsmMinGprsQosTable 1 }
C3gGsmMinGprsQosEntry ::= SEQUENCE {
c3gGsmMinGprsQosPrecedence C3gGprsQosPrecedence,
c3gGsmMinGprsQosDelay C3gGprsQosDelay,
c3gGsmMinGprsQosReliability C3gGprsQosReliability,
c3gGsmMinGprsQosPeakRate C3gGprsQosPeakRate,
c3gGsmMinGprsQosMeanRate C3gGprsQosMeanRate,
c3gGsmMinGprsQosRowStatus RowStatus
}
c3gGsmMinGprsQosPrecedence OBJECT-TYPE
SYNTAX C3gGprsQosPrecedence
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Minimum GPRS QoS precedence."
::= { c3gGsmMinGprsQosEntry 1 }
c3gGsmMinGprsQosDelay OBJECT-TYPE
SYNTAX C3gGprsQosDelay
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Minimum GPRS QoS delay classes."
::= { c3gGsmMinGprsQosEntry 2 }
c3gGsmMinGprsQosReliability OBJECT-TYPE
SYNTAX C3gGprsQosReliability
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Minimum GPRS QoS reliability."
::= { c3gGsmMinGprsQosEntry 3 }
c3gGsmMinGprsQosPeakRate OBJECT-TYPE
SYNTAX C3gGprsQosPeakRate
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Minimum GPRS QoS peak rate."
::= { c3gGsmMinGprsQosEntry 4 }
c3gGsmMinGprsQosMeanRate OBJECT-TYPE
SYNTAX C3gGprsQosMeanRate
UNITS "octet-per-hour"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Minimum GPRS QoS mean rate."
::= { c3gGsmMinGprsQosEntry 5 }
c3gGsmMinGprsQosRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The status of this conceptual row. This object is used to
manage creation, modification and deletion of rows in this
table."
::= { c3gGsmMinGprsQosEntry 6 }
c3gGsmNegoGprsQosTable OBJECT-TYPE
SYNTAX SEQUENCE OF C3gGsmNegoGprsQosEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Negotiated GPRS QoS table. This table contains negotiated GPRS
QoS parameters returned in the Activate PDP Context Accept
message. The objects in this table are valid only if the value
of object c3gGsmPacketSessionStatus defined in
c3gGsmPacketSessionTable is 'active'. This table is applicable
only in 3G technology mode."
::= { c3gGsmPdpProfile 8 }
c3gGsmNegoGprsQosEntry OBJECT-TYPE
SYNTAX C3gGsmNegoGprsQosEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (conceptual row) in the c3gGsmNegoGprsQosTable."
INDEX {
entPhysicalIndex,
c3gGsmPdpProfileIndex
}
::= { c3gGsmNegoGprsQosTable 1 }
C3gGsmNegoGprsQosEntry ::= SEQUENCE {
c3gGsmNegoGprsQosPrecedence C3gGprsQosPrecedence,
c3gGsmNegoGprsQosDelay C3gGprsQosDelay,
c3gGsmNegoGprsQosReliability C3gGprsQosReliability,
c3gGsmNegoGprsQosPeakRate C3gGprsQosPeakRate,
c3gGsmNegoGprsQosMeanRate C3gGprsQosMeanRate
}
c3gGsmNegoGprsQosPrecedence OBJECT-TYPE
SYNTAX C3gGprsQosPrecedence
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Negotiated GPRS QoS precedence."
::= { c3gGsmNegoGprsQosEntry 1 }
c3gGsmNegoGprsQosDelay OBJECT-TYPE
SYNTAX C3gGprsQosDelay
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Negotiated GPRS QoS delay classes."
::= { c3gGsmNegoGprsQosEntry 2 }
c3gGsmNegoGprsQosReliability OBJECT-TYPE
SYNTAX C3gGprsQosReliability
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Negotiated GPRS QoS reliability."
::= { c3gGsmNegoGprsQosEntry 3 }
c3gGsmNegoGprsQosPeakRate OBJECT-TYPE
SYNTAX C3gGprsQosPeakRate
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Negotiated GPRS QoS peak rate."
::= { c3gGsmNegoGprsQosEntry 4 }
c3gGsmNegoGprsQosMeanRate OBJECT-TYPE
SYNTAX C3gGprsQosMeanRate
UNITS "octet-per-hour"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Negotiated GPRS QoS mean rate."
::= { c3gGsmNegoGprsQosEntry 5 }
c3gGsmRadio OBJECT IDENTIFIER
::= { c3gWanGsm 4 }
c3gGsmRadioTable OBJECT-TYPE
SYNTAX SEQUENCE OF C3gGsmRadioEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Cellular 3G GSM/4G-LTE radio table."
::= { c3gGsmRadio 1 }
c3gGsmRadioEntry OBJECT-TYPE
SYNTAX C3gGsmRadioEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (conceptual row) in the c3gGsmRadioTable."
INDEX { entPhysicalIndex }
::= { c3gGsmRadioTable 1 }
C3gGsmRadioEntry ::= SEQUENCE {
c3gCurrentGsmRssi C3gRssi,
c3gCurrentGsmEcIo C3gEcIo,
c3gGsmCurrentBand INTEGER,
c3gGsmChannelNumber Unsigned32,
c3gGsmNumberOfNearbyCell Unsigned32
}
c3gCurrentGsmRssi OBJECT-TYPE
SYNTAX C3gRssi
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The GPRS/UMTS/LTE RSSI value."
::= { c3gGsmRadioEntry 1 }
c3gCurrentGsmEcIo OBJECT-TYPE
SYNTAX C3gEcIo
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The GPRS, UMTS or LTE Ec/Io value."
::= { c3gGsmRadioEntry 2 }
c3gGsmCurrentBand OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
invalid(2),
none(3),
gsm850(4),
gsm900(5),
gsm1800(6),
gsm1900(7),
wcdma800(8),
wcdma850(9),
wcdma1900(10),
wcdma2100(11),
lteBand(12)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"GPRS/UMTS/LTE band to which the modem is attached.
Refer CISCO-WAN-CELL-EXT-MIB for LTE band number when
in LTE mode."
DEFVAL { unknown }
::= { c3gGsmRadioEntry 3 }
c3gGsmChannelNumber OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Channel number to which the modem is attached. This is only
applicable in 3G technology mode. Refer CISCO-WAN-CELL-EXT-MIB
for the LTE uplink and downlink channel values"
DEFVAL { 0 }
::= { c3gGsmRadioEntry 4 }
c3gGsmNumberOfNearbyCell OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the current total number of
nearby cell in the c3gGsmNearbyCellTable. User can
poll this object to get the total number of nearby
cell before polling c3gGsmNearbyCellTable."
DEFVAL { 0 }
::= { c3gGsmRadioEntry 5 }
c3gGsmNearbyCellTable OBJECT-TYPE
SYNTAX SEQUENCE OF C3gGsmNearbyCellEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Cellular GSM/4G-LTE nearby cell table. Object
c3gGsmNumberOfNearbyCell indicates the total
number of nearby cell in this table."
::= { c3gGsmRadio 2 }
c3gGsmNearbyCellEntry OBJECT-TYPE
SYNTAX C3gGsmNearbyCellEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (conceptual row) in the c3gGsmNearbyCellTable."
INDEX {
entPhysicalIndex,
c3gGsmNearbyCellIndex
}
::= { c3gGsmNearbyCellTable 1 }
C3gGsmNearbyCellEntry ::= SEQUENCE {
c3gGsmNearbyCellIndex Integer32,
c3gGsmNearbyCellPrimaryScramblingCode Unsigned32,
c3gGsmNearbyCellRscp Integer32,
c3gGsmNearbyCellEcIoMeasurement C3gEcIo
}
c3gGsmNearbyCellIndex OBJECT-TYPE
SYNTAX Integer32 (1..100)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Nearby cell index, combined with entPhysicalIndex to access
the Nearby cell table c3gGsmNearbyCellTable."
::= { c3gGsmNearbyCellEntry 1 }
c3gGsmNearbyCellPrimaryScramblingCode OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Nearby cell primary scrambling code."
::= { c3gGsmNearbyCellEntry 2 }
c3gGsmNearbyCellRscp OBJECT-TYPE
SYNTAX Integer32 (-150..0)
UNITS "dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Nearby cell Received Signal Code Power (RSCP)."
::= { c3gGsmNearbyCellEntry 3 }
c3gGsmNearbyCellEcIoMeasurement OBJECT-TYPE
SYNTAX C3gEcIo
UNITS "dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Nearby cell Ec/Io measurement."
::= { c3gGsmNearbyCellEntry 4 }
c3gGsmHistoryTable OBJECT-TYPE
SYNTAX SEQUENCE OF C3gGsmHistoryEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Cellular 3G GSM/4G-LTE RSSI history table. The history of RSSI
are carried in an octet of string. Each octet in the octet
string has a value from 0 to 150 and the 255 value is reserved
to indicate an uninitialized (Invalid) value. The format of
the octet string with n octets is as following:
[ octet 0 is latest,
octet 1 is latest-1,
.
.
octet n-2 is oldest-1,
octet n-1 is oldest ]
To convert the provided value into dBm the following formula
should be used:
dBm = (-1)*value;"
::= { c3gGsmRadio 3 }
c3gGsmHistoryEntry OBJECT-TYPE
SYNTAX C3gGsmHistoryEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (conceptual row) in the c3gGsmHistoryTable."
INDEX { entPhysicalIndex }
::= { c3gGsmHistoryTable 1 }
C3gGsmHistoryEntry ::= SEQUENCE {
c3gGsmHistoryRssiPerSecond OCTET STRING,
c3gGsmHistoryRssiPerMinute OCTET STRING,
c3gGsmHistoryRssiPerHour OCTET STRING
}
c3gGsmHistoryRssiPerSecond OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (60))
UNITS "-dBm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Per-second RSSI history. This object contains a
per-second history of RSSI values for the last 60 seconds."
::= { c3gGsmHistoryEntry 1 }
c3gGsmHistoryRssiPerMinute OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (60))
UNITS "-dBm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Per-minute weakest RSSI value history. This object
contains a per-minute history of weakest RSSI values for the
last 60 minutes. The octet in the string is the weakest RSSI
value measured in a minute interval."
::= { c3gGsmHistoryEntry 2 }
c3gGsmHistoryRssiPerHour OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (72))
UNITS "-dBm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Per-hour weakest RSSI value history. This object
contains a per-hour history of weakest RSSI values for the last
72 hours. The octet in the string is the weakest RSSI value
measured in an hour interval."
::= { c3gGsmHistoryEntry 3 }
c3gGsmSecurity OBJECT IDENTIFIER
::= { c3gWanGsm 5 }
c3gGsmSecurityTable OBJECT-TYPE
SYNTAX SEQUENCE OF C3gGsmSecurityEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Cellular 3G GSM/4G-LTE security table."
::= { c3gGsmSecurity 1 }
c3gGsmSecurityEntry OBJECT-TYPE
SYNTAX C3gGsmSecurityEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (conceptual row) in the c3gGsmSecurityTable."
INDEX { entPhysicalIndex }
::= { c3gGsmSecurityTable 1 }
C3gGsmSecurityEntry ::= SEQUENCE {
c3gGsmChv1 INTEGER,
c3gGsmSimStatus INTEGER,
c3gGsmSimUserOperationRequired INTEGER,
c3gGsmNumberOfRetriesRemaining Unsigned32
}
c3gGsmChv1 OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
disabled(2),
enabled(3)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Card Holder Verification 1 (CHV1), if enabled, the PIN will be
verified, if disabled, the PIN will not be verified."
DEFVAL { disabled }
::= { c3gGsmSecurityEntry 1 }
c3gGsmSimStatus OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
ok(2),
notInserted(3),
removed(4),
initFailure(5),
generalFailure(6),
locked(7),
chv1Blocked(8),
chv2Blocked(9),
chv1Rejected(10),
chv2Rejected(11),
mepLocked(12),
networkRejected(13)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"SIM status. Indicates whether the SIM is present or removed
from the SIM socket, and its current status."
DEFVAL { unknown }
::= { c3gGsmSecurityEntry 2 }
c3gGsmSimUserOperationRequired OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
none(2),
enterChv1(3),
enterChv2(4),
enterUnblockChv1(5),
enterUnblockChv2(6),
enterMepCode(7)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If the SIM is protected (for example, because of CHV1 enabled),
it will indicate the type of user operation required."
DEFVAL { unknown }
::= { c3gGsmSecurityEntry 3 }
c3gGsmNumberOfRetriesRemaining OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the number of attempts remaining in case the SIM is
locked. If the number of retries becomes zero, the SIM is
blocked and becomes unusable."
DEFVAL { 0 }
::= { c3gGsmSecurityEntry 4 }
c3gWanLbsCommon OBJECT IDENTIFIER
::= { c3gWanLbs 1 }
c3gWanLbsCommonTable OBJECT-TYPE
SYNTAX SEQUENCE OF C3gWanLbsCommonEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains information about the Cellular Location
Based service feature. This GPS data is provided by the wireless
modem upon GPS configuration."
::= { c3gWanLbsCommon 1 }
c3gWanLbsCommonEntry OBJECT-TYPE
SYNTAX C3gWanLbsCommonEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This entry contains information about the
Cellular Location Based service
variables returned by the wireless modem."
INDEX { entPhysicalIndex }
::= { c3gWanLbsCommonTable 1 }
C3gWanLbsCommonEntry ::= SEQUENCE {
c3gLbsModeSelected INTEGER,
c3gLbsState INTEGER,
c3gLbsLocFixError INTEGER,
c3gLbsLatitude SnmpAdminString,
c3gLbsLongitude SnmpAdminString,
c3gLbsTimeStamp SnmpAdminString,
c3gLbsLocUncertaintyAngle Unsigned32,
c3gLbsLocUncertaintyA Unsigned32,
c3gLbsLocUncertaintyPos Unsigned32,
c3gLbsFixtype INTEGER,
c3gLbsHeightValid TruthValue,
c3gLbsHeight Integer32,
c3gLbsLocUncertaintyVertical Unsigned32,
c3gLbsVelocityValid TruthValue,
c3gLbsHeading Unsigned32,
c3gLbsVelocityHorizontal Unsigned32,
c3gLbsVelocityVertical Unsigned32,
c3gLbsHepe Unsigned32,
c3gLbsNumSatellites Gauge32
}
c3gLbsModeSelected OBJECT-TYPE
SYNTAX INTEGER {
unKnown(1),
standAlone(2),
msBased(3),
msAssist(4),
reserved(5)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Mode of Location base service selected.
unKnown - mode selection unkown
standAlone - Standalone mode
msBased - MS-Based mode
msAssist - MS-Assist mode
reserved - reserved for future use"
DEFVAL { unKnown }
::= { c3gWanLbsCommonEntry 1 }
c3gLbsState OBJECT-TYPE
SYNTAX INTEGER {
gpsDisabled(1),
gpsAcquiring(2),
gpsEnabled(3),
gpsLocError(4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Location base service state.
gpsDisabled - GPS is disabled
gpsEnabled - GPS is enabled
gpsLocError - GPS encounters error
gpsAcquiring - GPS is acquiring fix"
DEFVAL { gpsDisabled }
::= { c3gWanLbsCommonEntry 2 }
c3gLbsLocFixError OBJECT-TYPE
SYNTAX INTEGER {
offline(1),
noService(2),
noConnection(3),
noData(4),
sessionBusy(5),
reserved(6),
gpsDisabled(7),
connectionFailed(8),
errorState(9),
clientEnded(10),
uiEnded(11),
networkEnded(12),
timeout(13),
privacyLevel(14),
networkAccessError(15),
fixError(16),
pdeRejected(17),
trafficChannelExited(18),
e911(19),
serverError(20),
staleBSinformation(21),
resourceContention(22),
authenticationParameterFailed(23),
authenticationFailedLocal(24),
authenticationFailedNetwork(25),
vxLcsAgentAuthFail(26),
unknownSystemError(27),
unsupportedService(28),
subscriptionViolation(29),
desiredFixMethodFailed(30),
antennaSwitch(31),
noTxConfirmationReceived(32),
normalEndOfSession(33),
noErrorFromNetwork(34),
noResourcesLeftOnNetwork(35),
positionServerNotAvailable(36),
unsupportedProtocolVersion(37),
ssmolrErrorSystemFailure(38),
ssmolrErrorUnexpectedDataValue(39),
ssmolrErrorDataMissing(40),
ssmolrErrorFacilityNotSupported(41),
ssmolrErrorSsSubscriptionViolation(42),
ssmolrErrorPositionMethodFailure(43),
ssmolrErrorUndefined(44),
smlcTimeout(45),
mtGguardTimeExpired(46),
additionalAssistanceNeeded(47),
noFixError(48)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Location base service fix error code."
REFERENCE
"Refer to the following documents for the error code's full
definitions. Sierra Wireless CDMA EVDO CnS Reference_1.2.pdf
under Location Based Services section."
DEFVAL { noFixError }
::= { c3gWanLbsCommonEntry 3 }
c3gLbsLatitude OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Location base service Latitude."
::= { c3gWanLbsCommonEntry 4 }
c3gLbsLongitude OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Location base service longitude."
::= { c3gWanLbsCommonEntry 5 }
c3gLbsTimeStamp OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Location base service timestamp."
::= { c3gWanLbsCommonEntry 6 }
c3gLbsLocUncertaintyAngle OBJECT-TYPE
SYNTAX Unsigned32
UNITS "degrees"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"GPS Uncertainty parameter Angle, in degrees
for the Uncertainty info returned by the GPS
device while doing a location fix."
DEFVAL { 0 }
::= { c3gWanLbsCommonEntry 7 }
c3gLbsLocUncertaintyA OBJECT-TYPE
SYNTAX Unsigned32
UNITS "meters"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"GPS Uncertainty parameter A, value in meters
for the Uncertainty info returned by the GPS
device while doing a location fix."
DEFVAL { 0 }
::= { c3gWanLbsCommonEntry 8 }
c3gLbsLocUncertaintyPos OBJECT-TYPE
SYNTAX Unsigned32
UNITS "meters"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"GPS Uncertainty parameter position, value in meters
for the Uncertainty info returned by the GPS device
while doing a location fix."
DEFVAL { 0 }
::= { c3gWanLbsCommonEntry 9 }
c3gLbsFixtype OBJECT-TYPE
SYNTAX INTEGER {
none(1),
twoDimension(2),
threeDimension(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The type of location fix in Location Base service.
none - default case, while LBS is not enabled.
twoDimension - 2D location fix.
threeDimension - 3D location fix."
DEFVAL { none }
::= { c3gWanLbsCommonEntry 10 }
c3gLbsHeightValid OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates whether the height returned by
the GPS device is valid during location fix."
DEFVAL { false }
::= { c3gWanLbsCommonEntry 11 }
c3gLbsHeight OBJECT-TYPE
SYNTAX Integer32 (-500..500)
UNITS "meters"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the GPS height parameter returned
by the GPS device while performing location fix."
DEFVAL { 0 }
::= { c3gWanLbsCommonEntry 12 }
c3gLbsLocUncertaintyVertical OBJECT-TYPE
SYNTAX Unsigned32
UNITS "meters"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"GPS parameter vertical velocity parameter returned by
the GPS device while performing location fix."
DEFVAL { 0 }
::= { c3gWanLbsCommonEntry 13 }
c3gLbsVelocityValid OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates whether the Velocity value
returned by the GPS device is valid."
DEFVAL { false }
::= { c3gWanLbsCommonEntry 14 }
c3gLbsHeading OBJECT-TYPE
SYNTAX Unsigned32
UNITS "degrees"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The compass direction toward which the GPS receiver
is (or should be) moving."
DEFVAL { 0 }
::= { c3gWanLbsCommonEntry 15 }
c3gLbsVelocityHorizontal OBJECT-TYPE
SYNTAX Unsigned32
UNITS "meters per second"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Horizontal Velocity in meters per second the GPS
device is heading. This is the value returned by
the GPS satellite relative to the last horizontal
location of the GPS device. If at Time X satellite
sees the location of GPS device is L1 and then at
Time Y satellite sees the location is L2 then
speed is (L2 - L1) / ( Y - X)."
DEFVAL { 0 }
::= { c3gWanLbsCommonEntry 16 }
c3gLbsVelocityVertical OBJECT-TYPE
SYNTAX Unsigned32
UNITS "meters per second"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Vertical Velocity in meters per second
the GPS device is heading. This is the value returned by
the GPS satellite relative to the last vertical location of
the GPS device. If at Time X satellite sees the location
of GPS device is L1 and then at Time Y satellite sees
the location is L2 then speed is (L2 - L1) / ( Y - X)."
DEFVAL { 0 }
::= { c3gWanLbsCommonEntry 17 }
c3gLbsHepe OBJECT-TYPE
SYNTAX Unsigned32
UNITS "centimeters"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Horizontal Estimated Position Error returned by the
GPS satellite for current position of the GPS device."
DEFVAL { 0 }
::= { c3gWanLbsCommonEntry 18 }
c3gLbsNumSatellites OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of GPS satellites in vision to the modem
while GPS tracking is on."
DEFVAL { 0 }
::= { c3gWanLbsCommonEntry 19 }
c3gWanLbsSatelliteInfo OBJECT IDENTIFIER
::= { c3gWanLbs 2 }
c3gWanLbsSatelliteInfoTable OBJECT-TYPE
SYNTAX SEQUENCE OF C3gWanLbsSatelliteInfoEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides information on each satellite that is
visible to the modem during the location fix. These
satellites guide the device to acquire a 2D or 3D
location fix."
::= { c3gWanLbsSatelliteInfo 1 }
c3gWanLbsSatelliteInfoEntry OBJECT-TYPE
SYNTAX C3gWanLbsSatelliteInfoEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides information about each satellite's
elevation, azimuth, Signal to Noise ratio (SNR) and
its reference number local to the router."
INDEX {
entPhysicalIndex,
c3gWanLbsSatelliteInfoIndex
}
::= { c3gWanLbsSatelliteInfoTable 1 }
C3gWanLbsSatelliteInfoEntry ::= SEQUENCE {
c3gWanLbsSatelliteInfoIndex Integer32,
c3gWanLbsSatelliteNumber Integer32,
c3gWanLbsSatelliteElevation Integer32,
c3gWanLbsSatelliteAzimuth Integer32,
c3gWanLbsSatelliteInfoSignalNoiseRatio Integer32,
c3gWanLbsSatelliteUsed TruthValue,
c3gWanLbsSatelliteInfoRowStatus RowStatus
}
c3gWanLbsSatelliteInfoIndex OBJECT-TYPE
SYNTAX Integer32 (1..1000)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An index that is assigned to each satellite under a modem
and in combination with entPhysicalIndex uniquely identify it.
This index is assigned arbitrarily by the engine and is not
saved over reboots."
::= { c3gWanLbsSatelliteInfoEntry 1 }
c3gWanLbsSatelliteNumber OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Each Satellite is assigned a unique number
within this device.This object can be used
to locate a particular satellite under
a modem."
REFERENCE
"Refer to the following documents for detailed
information of Satellites.
Sierra Wireless CDMA EVDO CnS Reference_1.2.pdf under
Location Based Services section"
::= { c3gWanLbsSatelliteInfoEntry 2 }
c3gWanLbsSatelliteElevation OBJECT-TYPE
SYNTAX Integer32
UNITS "degrees"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Angle of Elevation between the GPS antenna pointing direction,
directly towards the satellite, and the local horizontal plane.
It is the up-down angle"
REFERENCE
"Refer to the following documents for detailed
information of Satellites elevation.
Sierra Wireless CDMA EVDO CnS Reference_1.2.pdf under
Location Based Services section"
::= { c3gWanLbsSatelliteInfoEntry 3 }
c3gWanLbsSatelliteAzimuth OBJECT-TYPE
SYNTAX Integer32
UNITS "degrees"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Azimuth of the current satellite in context
referenced by the Satellite InfoIndex.
Azimuth is the degree of rotation of the
satellites dish on its vertical plane."
REFERENCE
"Refer to the following documents for detailed
information of Satellites Azimuth.
Sierra Wireless CDMA EVDO CnS Reference_1.2.pdf under
Location Based Services section"
::= { c3gWanLbsSatelliteInfoEntry 4 }
c3gWanLbsSatelliteInfoSignalNoiseRatio OBJECT-TYPE
SYNTAX Integer32
UNITS "db"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Signal to Noise Ratio(SNR) of received GPS signal.
SNR is refered to as the signal strength in
GPS standards."
REFERENCE
"Refer to the following documents for detailed
information of signal to noise ration in LBS.
Sierra Wireless CDMA EVDO CnS Reference_1.2.pdf under
Location Based Services section"
::= { c3gWanLbsSatelliteInfoEntry 5 }
c3gWanLbsSatelliteUsed OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Is this satellite in line of sight to the
modem used in calculating the GPS location?"
DEFVAL { false }
::= { c3gWanLbsSatelliteInfoEntry 6 }
c3gWanLbsSatelliteInfoRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The status of this conceptual row. This object is used to
manage creation, modification and deletion of rows in this
table."
::= { c3gWanLbsSatelliteInfoEntry 7 }
c3gWanSms OBJECT IDENTIFIER
::= { c3gWanSmsCommon 1 }
c3gSmsCommonTable OBJECT-TYPE
SYNTAX SEQUENCE OF C3gSmsCommonEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains Cellular SMS management
MIB objects."
::= { c3gWanSms 1 }
c3gSmsCommonEntry OBJECT-TYPE
SYNTAX C3gSmsCommonEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry contains counters for the SMS messages
received, placed, errored and archived on CDMA,
GSM or LTE based modems."
INDEX { entPhysicalIndex }
::= { c3gSmsCommonTable 1 }
C3gSmsCommonEntry ::= SEQUENCE {
c3gSmsServiceAvailable TruthValue,
c3gSmsOutSmsCount Counter32,
c3gSmsOutSmsErrorCount Counter32,
c3gSmsInSmsStorageUsed Gauge32,
c3gSmsInSmsStorageUnused Gauge32,
c3gSmsInSmsArchiveCount Gauge32,
c3gSmsInSmsArchiveErrorCount Gauge32,
c3gSmsArchiveUrl SnmpAdminString,
c3gSmsOutSmsStatus INTEGER,
c3gSmsInSmsCount Counter32,
c3gSmsInSmsDeleted Counter32,
c3gSmsInSmsStorageMax Counter64,
c3gSmsInSmsCallBack Counter32,
c3gSmsOutSmsPendingCount Gauge32,
c3gSmsOutSmsArchiveCount Gauge32,
c3gSmsOutSmsArchiveErrorCount Gauge32,
c3gSmsInSmsArchived Gauge32
}
c3gSmsServiceAvailable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the availability of SMS Service."
DEFVAL { false }
::= { c3gSmsCommonEntry 1 }
c3gSmsOutSmsCount OBJECT-TYPE
SYNTAX Counter32
UNITS "msgs"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of SMS messages which have been sent
successfully."
::= { c3gSmsCommonEntry 2 }
c3gSmsOutSmsErrorCount OBJECT-TYPE
SYNTAX Counter32
UNITS "msgs"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of SMS message that could not be sent."
::= { c3gSmsCommonEntry 3 }
c3gSmsInSmsStorageUsed OBJECT-TYPE
SYNTAX Gauge32
UNITS "msgs"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of SMS message records space used in the
Incoming SMS message storage. One standard
SMS message (cdma or gsm) occupies 1 unit of
record storage space. A big SMS message can span
'n' sms record space but still be called as 1 SMS
message. Storage used can be greater than or equal
to total number of Incoming SMS received."
::= { c3gSmsCommonEntry 4 }
c3gSmsInSmsStorageUnused OBJECT-TYPE
SYNTAX Gauge32
UNITS "msgs"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of SMS messages record space left
unused in the Incoming SMS message storage.
This is equal to c3gSmsInSmsStorageMax -
c3gSmsInSmsStorageUsed."
::= { c3gSmsCommonEntry 5 }
c3gSmsInSmsArchiveCount OBJECT-TYPE
SYNTAX Gauge32
UNITS "msgs"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of successful archive of Incoming SMS messages
since router reload. Each SMS message occupies x bytes of
space. So if the incoming message is huge, then it is
archived as multiple of x bytes but still called as one
SMS message. This is the difference between
c3gSmsInSmsArchiveCount and c3gSmsInSmsArchived."
::= { c3gSmsCommonEntry 6 }
c3gSmsInSmsArchiveErrorCount OBJECT-TYPE
SYNTAX Gauge32
UNITS "msgs"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of Incoming SMS messages that could not be
archived since device was reloaded."
::= { c3gSmsCommonEntry 7 }
c3gSmsArchiveUrl OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"URL of the sms archive directory on the ftp server.
The url will be of this format
ftp://x.y.z.k/user/dirname"
::= { c3gSmsCommonEntry 8 }
c3gSmsOutSmsStatus OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
success(2),
copySmsHeader(3),
copySmsBody(4),
sent(5),
receivedSentNotification(6),
receivedOutMsgNumber(7),
receivedOutMsgStatus(8)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Status of the last send operation of outgoing
SMS message to the network."
::= { c3gSmsCommonEntry 9 }
c3gSmsInSmsCount OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of SMS messages which have been
received successfully and stored in router.
These SMS's are a mirror copy of SMS stored in
Modem or SIM"
::= { c3gSmsCommonEntry 10 }
c3gSmsInSmsDeleted OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of SMS messages which have been
deleted since router boot up. This does
not include SMS messages that are already
archived."
::= { c3gSmsCommonEntry 11 }
c3gSmsInSmsStorageMax OBJECT-TYPE
SYNTAX Counter64
UNITS "msgs"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of SMS message records space allocated
in the router's DRAM to store Incoming SMS messages."
::= { c3gSmsCommonEntry 12 }
c3gSmsInSmsCallBack OBJECT-TYPE
SYNTAX Counter32
UNITS "msgs"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of incoming SMS messages that triggered
callback."
::= { c3gSmsCommonEntry 13 }
c3gSmsOutSmsPendingCount OBJECT-TYPE
SYNTAX Gauge32
UNITS "msgs"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of outgoing SMS messages that are in
pending queue of the router."
::= { c3gSmsCommonEntry 14 }
c3gSmsOutSmsArchiveCount OBJECT-TYPE
SYNTAX Gauge32
UNITS "msgs"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of successfull archive of outgoing SMS messages
since router reload."
::= { c3gSmsCommonEntry 15 }
c3gSmsOutSmsArchiveErrorCount OBJECT-TYPE
SYNTAX Gauge32
UNITS "msgs"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of failed archive of outgoing SMS messages
since router reload."
::= { c3gSmsCommonEntry 16 }
c3gSmsInSmsArchived OBJECT-TYPE
SYNTAX Gauge32
UNITS "msgs"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of Incoming SMS messages that are successfully
archived since router reload."
::= { c3gSmsCommonEntry 17 }
-- Default Notification Type
c3gModemUpNotif NOTIFICATION-TYPE
OBJECTS { entPhysicalName }
STATUS current
DESCRIPTION
"This is the notification that the modem has been detected by
host interface. Users can enable or disable the generation of
this notification by using object c3gModemUpNotifEnabled."
::= { ciscoWan3gMIBNotifs 1 }
c3gModemDownNotif NOTIFICATION-TYPE
OBJECTS { entPhysicalName }
STATUS current
DESCRIPTION
"This is the notification that the modem has not been detected
by host interface, or has been disconnected from host interface.
Users can enable or disable the generation of this notification
by using object c3gModemDownNotifEnabled."
::= { ciscoWan3gMIBNotifs 2 }
c3gServiceChangedNotif NOTIFICATION-TYPE
OBJECTS {
c3gPreviousServiceType,
c3gCurrentServiceType
}
STATUS current
DESCRIPTION
"Notification for service change event. Objects
c3gPreviousServiceType and c3gCurrentServiceType will be
included in the notification. Users can enable or disable the
generation of this notification by using object
c3gServiceChangedNotifEnabled."
::= { ciscoWan3gMIBNotifs 3 }
c3gNetworkChangedNotif NOTIFICATION-TYPE
OBJECTS {
c3gCurrentSid,
c3gCurrentNid,
c3gGsmMcc,
c3gGsmMnc,
c3gRoamingStatus
}
STATUS current
DESCRIPTION
"Notification for network change event. Objects c3gCurrentSid,
c3gCurrentNid, c3gGsmMcc, c3gGsmMnc and c3gRoamingStatus will
be included in the notification. Users can enable or disable
the generation of this notification by using object
c3gNetworkChangedNotifEnabled."
::= { ciscoWan3gMIBNotifs 4 }
c3gConnectionStatusChangedNotif NOTIFICATION-TYPE
OBJECTS {
c3gConnectionStatus,
c3gCurrentServiceType
}
STATUS current
DESCRIPTION
"Notification for connection status change event. Objects
c3gConnectionStatus and c3gCurrentServiceType will be included
in the notification. Users can use object
c3gConnectionStatusChangedNotifFlag to control what connection
status changes will cause the generation of this notification."
::= { ciscoWan3gMIBNotifs 5 }
c3gRssiOnsetNotif NOTIFICATION-TYPE
OBJECTS {
c3gNotifRadioService,
c3gNotifRssi
}
STATUS current
DESCRIPTION
"If RSSI goes below c3gRssiOnsetNotifThreshold and the service
bit in c3gRssiOnsetNotifFlag is set, this notification will be
generated. Object c3gNotifRadioService will indicate which
service generates this notification and the associated RSSI
will be reported in c3gNotifRssi. Please note that c3gNotifRssi
is used to indicate the RSSI value that triggers the
notification, user should go to the corresponding radio table to
get the current RSSI value."
::= { ciscoWan3gMIBNotifs 6 }
c3gRssiAbateNotif NOTIFICATION-TYPE
OBJECTS {
c3gNotifRadioService,
c3gNotifRssi
}
STATUS current
DESCRIPTION
"If RSSI goes above c3gRssiAbateNotifThreshold and the service
bit in c3gRssiAbateNotifFlag is set, this notification will be
generated. Object c3gNotifRadioService will indicate which
service generates this notification and the associated RSSI
will be reported in c3gNotifRssi. Please note that c3gNotifRssi
is used to indicate the RSSI value that triggers the
notification, user should go to the corresponding radio table to
get the current RSSI value."
::= { ciscoWan3gMIBNotifs 7 }
c3gEcIoOnsetNotif NOTIFICATION-TYPE
OBJECTS {
c3gNotifRadioService,
c3gNotifEcIo
}
STATUS current
DESCRIPTION
"If Ec/Io goes below c3gEcIoOnsetNotifThreshold and the service
bit in c3gEcIoOnsetNotifFlag is set, this notification will be
generated. Object c3gNotifRadioService will indicate which
service generates this notification and the associated Ec/Io
will be reported in c3gNotifEcIo. Please note that c3gNotifEcIo
is used to indicate the Ec/Io value that triggers the
notification, user should go to the corresponding radio table to
get the current Ec/Io value."
::= { ciscoWan3gMIBNotifs 8 }
c3gEcIoAbateNotif NOTIFICATION-TYPE
OBJECTS {
c3gNotifRadioService,
c3gNotifEcIo
}
STATUS current
DESCRIPTION
"If Ec/Io goes above c3gEcIoAbateNotifThreshold and the service
bit in c3gEcIoAbateNotifFlag is set, this notification will be
generated. Object c3gNotifRadioService will indicate which
service generates this notification and the associated Ec/Io
will be reported in c3gNotifEcIo. Please note that c3gNotifEcIo
is used to indicate the Ec/Io value that triggers the
notification, user should go to the corresponding radio table to
get the current Ec/Io value."
::= { ciscoWan3gMIBNotifs 9 }
c3gModemTemperOnsetNotif NOTIFICATION-TYPE
OBJECTS { c3gModemTemperature }
STATUS current
DESCRIPTION
"If modem temperature goes above
c3gModemTemperOnsetNotifThreshold and the value of
c3gModemTemperOnsetNotifEnabled is 'true', this notification
will be generated and the current value of c3gModemTemperature
will be included in this notification."
::= { ciscoWan3gMIBNotifs 10 }
c3gModemTemperAbateNotif NOTIFICATION-TYPE
OBJECTS { c3gModemTemperature }
STATUS current
DESCRIPTION
"If modem temperature goes below
c3gModemTemperAbateNotifThreshold and the value of
c3gModemTemperAbateNotifEnabled is 'true', this notification
will be generated and the current value of c3gModemTemperature
will be included in this notification."
::= { ciscoWan3gMIBNotifs 11 }
c3gModemTemperOnsetRecoveryNotif NOTIFICATION-TYPE
OBJECTS { c3gModemTemperature }
STATUS current
DESCRIPTION
"This trap is generated as a recovery notification for
c3gModemTemperOnsetNotif.This trap is generated when the current
value of c3gModemTemperature goes below
c3gModemTemperOnsetNotifThreshold once it has generated the
c3gModemTemperOnsetNotif and the value of
c3gModemTemperOnsetNotifEnabled is 'true'.
c3gModemTemperature contains the current value of modem
temperature."
::= { ciscoWan3gMIBNotifs 12 }
c3gModemTemperAbateRecoveryNotif NOTIFICATION-TYPE
OBJECTS { c3gModemTemperature }
STATUS current
DESCRIPTION
"This trap is generated as a recovery notification for
c3gModemTemperAbateNotif.This trap is generated when the current
value of c3gModemTemperature goes above
c3gModemTemperAbateNotifThreshold once it has generated the
c3gModemTemperAbateNotif and the value of
c3gModemTemperAbateNotifEnabled is 'true'
c3gModemTemperature contains the current value of modem
temperature"
::= { ciscoWan3gMIBNotifs 13 }
-- Conformance
ciscoWan3gMIBCompliances OBJECT IDENTIFIER
::= { ciscoWan3gMIBConform 1 }
ciscoWan3gMIBGroups OBJECT IDENTIFIER
::= { ciscoWan3gMIBConform 2 }
ciscoWan3gMIBCompliance MODULE-COMPLIANCE
STATUS deprecated
DESCRIPTION
"This is a default module-compliance
containing default object groups."
MODULE -- this module
MANDATORY-GROUPS {
ciscoWan3gMIBNotificationGroup,
ciscoWan3gMIBCommonObjectGroup
}
GROUP ciscoWan3gMIBCdmaObjectGroup
DESCRIPTION
"This object group should be included for CDMA standard."
GROUP ciscoWan3gMIBGsmObjectGroup
DESCRIPTION
"This object group should be included for GSM/LTE standard."
GROUP ciscoWan3gMIBSmsObjectGroup
DESCRIPTION
"This object group should be included
for SMS service on CDMA, GSM and LTE standard."
GROUP ciscoWan3gMIBLbsObjectGroup
DESCRIPTION
"This object group should be included for
Location based service on CDMA, GSM and LTE standard."
::= { ciscoWan3gMIBCompliances 1 }
ciscoWan3gMIBCompliance1 MODULE-COMPLIANCE
STATUS deprecated
DESCRIPTION
"The compliance statement for the CISCO-WAN-3G-MIB."
MODULE -- this module
MANDATORY-GROUPS {
ciscoWan3gMIBNotificationGroup,
ciscoWan3gMIBCommonObjectGroup
}
GROUP ciscoWan3gMIBCdmaObjectGroup
DESCRIPTION
"This object group should be included for CDMA standard."
GROUP ciscoWan3gMIBGsmObjectGroup
DESCRIPTION
"This object group should be included for GSM and
LTE standard."
GROUP ciscoWan3gMIBSmsObjectGroup
DESCRIPTION
"This object group should be included
for SMS service on CDMA, GSM and LTE standard."
GROUP ciscoWan3gMIBLbsObjectGroup
DESCRIPTION
"This object group should be included for
Location based service on CDMA, GSM and LTE standard."
::= { ciscoWan3gMIBCompliances 2 }
ciscoWan3gMIBComplianceRev1 MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"This is a default module-compliance
containing default object groups."
MODULE -- this module
MANDATORY-GROUPS {
ciscoWan3gMIBNotificationGroupRev1,
ciscoWan3gMIBCommonObjectGroup
}
GROUP ciscoWan3gMIBCdmaObjectGroup
DESCRIPTION
"This object group should be included for CDMA standard."
GROUP ciscoWan3gMIBGsmObjectGroup
DESCRIPTION
"This object group should be included for GSM/LTE standard."
GROUP ciscoWan3gMIBSmsObjectGroup
DESCRIPTION
"This object group should be included
for SMS service on CDMA, GSM and LTE standard."
GROUP ciscoWan3gMIBLbsObjectGroup
DESCRIPTION
"This object group should be included for
Location based service on CDMA, GSM and LTE standard."
::= { ciscoWan3gMIBCompliances 3 }
ciscoWan3gMIBCompliance1Rev1 MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for the CISCO-WAN-3G-MIB."
MODULE -- this module
MANDATORY-GROUPS {
ciscoWan3gMIBNotificationGroupRev1,
ciscoWan3gMIBCommonObjectGroup
}
GROUP ciscoWan3gMIBCdmaObjectGroup
DESCRIPTION
"This object group should be included for CDMA standard."
GROUP ciscoWan3gMIBGsmObjectGroup
DESCRIPTION
"This object group should be included for GSM and
LTE standard."
GROUP ciscoWan3gMIBSmsObjectGroup
DESCRIPTION
"This object group should be included
for SMS service on CDMA, GSM and LTE standard."
GROUP ciscoWan3gMIBLbsObjectGroup
DESCRIPTION
"This object group should be included for
Location based service on CDMA, GSM and LTE standard."
::= { ciscoWan3gMIBCompliances 4 }
-- Units of Conformance
ciscoWan3gMIBCommonObjectGroup OBJECT-GROUP
OBJECTS {
c3gStandard,
c3gCapability,
c3gModemState,
c3gPreviousServiceType,
c3gCurrentServiceType,
c3gRoamingStatus,
c3gCurrentSystemTime,
c3gConnectionStatus,
c3gNotifRadioService,
c3gNotifRssi,
c3gNotifEcIo,
c3gModemTemperature,
c3gRssiOnsetNotifThreshold,
c3gRssiAbateNotifThreshold,
c3gEcIoOnsetNotifThreshold,
c3gEcIoAbateNotifThreshold,
c3gModemTemperOnsetNotifThreshold,
c3gModemTemperAbateNotifThreshold,
c3gModemReset,
c3gModemUpNotifEnabled,
c3gModemDownNotifEnabled,
c3gServiceChangedNotifEnabled,
c3gNetworkChangedNotifEnabled,
c3gConnectionStatusChangedNotifFlag,
c3gRssiOnsetNotifFlag,
c3gRssiAbateNotifFlag,
c3gEcIoOnsetNotifFlag,
c3gEcIoAbateNotifFlag,
c3gModemTemperOnsetNotifEnabled,
c3gModemTemperAbateNotifEnabled,
c3gGpsState
}
STATUS current
DESCRIPTION
"A collection of common objects for Cellular interface."
::= { ciscoWan3gMIBGroups 1 }
ciscoWan3gMIBCdmaObjectGroup OBJECT-GROUP
OBJECTS {
c3gCdmaTotalCallDuration,
c3gCdmaTotalTransmitted,
c3gCdmaTotalReceived,
c3gHdrDdtmPreference,
c3gOutgoingCallNumber,
c3gHdrAtState,
c3gHdrSessionState,
c3gUati,
c3gColorCode,
c3gRati,
c3gHdrSessionDuration,
c3gHdrSessionStart,
c3gHdrSessionEnd,
c3gAuthStatus,
c3gHdrDrc,
c3gHdrDrcCover,
c3gHdrRri,
c3gCdmaCurrentTransmitted,
c3gCdmaCurrentReceived,
c3gCdmaCurrentCallStatus,
c3gCdmaCurrentCallDuration,
c3gCdmaCurrentCallType,
c3gCdmaLastCallDisconnReason,
c3gCdmaLastConnError,
c3gMobileIpErrorCode,
c3gEsn,
c3gModemActivationStatus,
c3gAccountActivationDate,
c3gCdmaRoamingPreference,
c3gPrlVersion,
c3gMdn,
c3gMsid,
c3gMsl,
c3gCdmaCurrentServiceStatus,
c3gCdmaHybridModePreference,
c3gCdmaCurrentRoamingStatus,
c3gCurrentIdleDigitalMode,
c3gCurrentSid,
c3gCurrentNid,
c3gCurrentCallSetupMode,
c3gSipUsername,
c3gSipPassword,
c3gServingBaseStationLongitude,
c3gServingBaseStationLatitude,
c3gNumberOfDataProfileConfigurable,
c3gCurrentActiveDataProfile,
c3gNai,
c3gAaaPassword,
c3gMnHaSs,
c3gMnHaSpi,
c3gMnAaaSs,
c3gMnAaaSpi,
c3gReverseTunnelPreference,
c3gHomeAddrType,
c3gHomeAddr,
c3gPriHaAddrType,
c3gPriHaAddr,
c3gSecHaAddrType,
c3gSecHaAddr,
c3gCurrent1xRttRssi,
c3gCurrent1xRttEcIo,
c3gCurrent1xRttChannelNumber,
c3gCurrent1xRttChannelState,
c3gCurrentEvDoRssi,
c3gCurrentEvDoEcIo,
c3gCurrentEvDoChannelNumber,
c3gSectorId,
c3gSubnetMask,
c3gHdrColorCode,
c3gPnOffset,
c3gRxMainGainControl,
c3gRxDiversityGainControl,
c3gTxTotalPower,
c3gTxGainAdjust,
c3gCarrierToInterferenceRatio,
c3g1xRttBandClass,
c3gEvDoBandClass,
c3gCdmaHistory1xRttRssiPerSecond,
c3gCdmaHistory1xRttRssiPerMinute,
c3gCdmaHistory1xRttRssiPerHour,
c3gCdmaHistoryEvDoRssiPerSecond,
c3gCdmaHistoryEvDoRssiPerMinute,
c3gCdmaHistoryEvDoRssiPerHour,
c3gCdmaPinSecurityStatus,
c3gCdmaPowerUpLockStatus
}
STATUS current
DESCRIPTION
"A collection of objects for Cellular 3G CDMA."
::= { ciscoWan3gMIBGroups 2 }
ciscoWan3gMIBGsmObjectGroup OBJECT-GROUP
OBJECTS {
c3gGsmTotalByteTransmitted,
c3gGsmTotalByteReceived,
c3gGsmPacketSessionStatus,
c3gGsmPdpType,
c3gGsmPdpAddress,
c3gGsmNegoUmtsQosTrafficClass,
c3gGsmNegoUmtsQosMaxUpLinkBitRate,
c3gGsmNegoUmtsQosMaxDownLinkBitRate,
c3gGsmNegoUmtsQosGuaUpLinkBitRate,
c3gGsmNegoUmtsQosGuaDownLinkBitRate,
c3gGsmNegoUmtsQosOrder,
c3gGsmNegoUmtsQosErroneousSdu,
c3gGsmNegoUmtsQosMaxSduSize,
c3gGsmNegoUmtsQosSer,
c3gGsmNegoUmtsQosBer,
c3gGsmNegoUmtsQosDelay,
c3gGsmNegoUmtsQosPriority,
c3gGsmNegoUmtsQosSrcStatDescriptor,
c3gGsmNegoUmtsQosSignalIndication,
c3gGsmNegoGprsQosPrecedence,
c3gGsmNegoGprsQosDelay,
c3gGsmNegoGprsQosReliability,
c3gGsmNegoGprsQosPeakRate,
c3gGsmNegoGprsQosMeanRate,
c3gImsi,
c3gImei,
c3gIccId,
c3gMsisdn,
c3gFsn,
c3gModemStatus,
c3gGsmRoamingPreference,
c3gGsmLac,
c3gGsmCurrentServiceStatus,
c3gGsmCurrentServiceError,
c3gGsmCurrentService,
c3gGsmPacketService,
c3gGsmCurrentRoamingStatus,
c3gGsmNetworkSelectionMode,
c3gGsmCountry,
c3gGsmNetwork,
c3gGsmMcc,
c3gGsmMnc,
c3gGsmRac,
c3gGsmCurrentCellId,
c3gGsmCurrentPrimaryScramblingCode,
c3gGsmPlmnSelection,
c3gGsmRegPlmn,
c3gGsmPlmnAbbr,
c3gGsmServiceProvider,
c3gGsmPdpProfileType,
c3gGsmPdpProfileAddr,
c3gGsmPdpProfileApn,
c3gGsmPdpProfileAuthenType,
c3gGsmPdpProfileUsername,
c3gGsmPdpProfilePassword,
c3gGsmPdpProfileRowStatus,
c3gGsmReqUmtsQosTrafficClass,
c3gGsmReqUmtsQosMaxUpLinkBitRate,
c3gGsmReqUmtsQosMaxDownLinkBitRate,
c3gGsmReqUmtsQosGuaUpLinkBitRate,
c3gGsmReqUmtsQosGuaDownLinkBitRate,
c3gGsmReqUmtsQosOrder,
c3gGsmReqUmtsQosErroneousSdu,
c3gGsmReqUmtsQosMaxSduSize,
c3gGsmReqUmtsQosSer,
c3gGsmReqUmtsQosBer,
c3gGsmReqUmtsQosDelay,
c3gGsmReqUmtsQosPriority,
c3gGsmReqUmtsQosSrcStatDescriptor,
c3gGsmReqUmtsQosSignalIndication,
c3gGsmReqUmtsQosRowStatus,
c3gGsmMinUmtsQosTrafficClass,
c3gGsmMinUmtsQosMaxUpLinkBitRate,
c3gGsmMinUmtsQosMaxDownLinkBitRate,
c3gGsmMinUmtsQosGuaUpLinkBitRate,
c3gGsmMinUmtsQosGuaDownLinkBitRate,
c3gGsmMinUmtsQosOrder,
c3gGsmMinUmtsQosErroneousSdu,
c3gGsmMinUmtsQosMaxSduSize,
c3gGsmMinUmtsQosSer,
c3gGsmMinUmtsQosBer,
c3gGsmMinUmtsQosDelay,
c3gGsmMinUmtsQosPriority,
c3gGsmMinUmtsQosSrcStatDescriptor,
c3gGsmMinUmtsQosSignalIndication,
c3gGsmMinUmtsQosRowStatus,
c3gGsmReqGprsQosPrecedence,
c3gGsmReqGprsQosDelay,
c3gGsmReqGprsQosReliability,
c3gGsmReqGprsQosPeakRate,
c3gGsmReqGprsQosMeanRate,
c3gGsmReqGprsQosRowStatus,
c3gGsmMinGprsQosPrecedence,
c3gGsmMinGprsQosDelay,
c3gGsmMinGprsQosReliability,
c3gGsmMinGprsQosPeakRate,
c3gGsmMinGprsQosMeanRate,
c3gGsmMinGprsQosRowStatus,
c3gCurrentGsmRssi,
c3gCurrentGsmEcIo,
c3gGsmCurrentBand,
c3gGsmChannelNumber,
c3gGsmNumberOfNearbyCell,
c3gGsmNearbyCellPrimaryScramblingCode,
c3gGsmNearbyCellRscp,
c3gGsmNearbyCellEcIoMeasurement,
c3gGsmHistoryRssiPerSecond,
c3gGsmHistoryRssiPerMinute,
c3gGsmHistoryRssiPerHour,
c3gGsmChv1,
c3gGsmSimStatus,
c3gGsmSimUserOperationRequired,
c3gGsmNumberOfRetriesRemaining
}
STATUS current
DESCRIPTION
"A collection of objects for Cellular 3G GSM and LTE."
::= { ciscoWan3gMIBGroups 3 }
ciscoWan3gMIBNotificationGroup NOTIFICATION-GROUP
NOTIFICATIONS {
c3gModemUpNotif,
c3gModemDownNotif,
c3gServiceChangedNotif,
c3gNetworkChangedNotif,
c3gConnectionStatusChangedNotif,
c3gRssiOnsetNotif,
c3gEcIoOnsetNotif,
c3gRssiAbateNotif,
c3gEcIoAbateNotif,
c3gModemTemperOnsetNotif,
c3gModemTemperAbateNotif
}
STATUS deprecated
DESCRIPTION
"A collection of objects for Cellular WAN notifications.
ciscoWan3gMIBNotificationGroup object is superseded by
ciscoWan3gMIBNotificationGroupRev1."
::= { ciscoWan3gMIBGroups 4 }
ciscoWan3gMIBLbsObjectGroup OBJECT-GROUP
OBJECTS {
c3gLbsModeSelected,
c3gLbsState,
c3gLbsLocFixError,
c3gLbsLatitude,
c3gLbsLongitude,
c3gLbsTimeStamp,
c3gLbsLocUncertaintyAngle,
c3gLbsLocUncertaintyA,
c3gLbsLocUncertaintyPos,
c3gLbsFixtype,
c3gLbsHeightValid,
c3gLbsHeight,
c3gLbsLocUncertaintyVertical,
c3gLbsVelocityValid,
c3gLbsHeading,
c3gLbsVelocityHorizontal,
c3gLbsVelocityVertical,
c3gLbsHepe,
c3gLbsNumSatellites,
c3gWanLbsSatelliteNumber,
c3gWanLbsSatelliteElevation,
c3gWanLbsSatelliteAzimuth,
c3gWanLbsSatelliteUsed,
c3gWanLbsSatelliteInfoSignalNoiseRatio,
c3gWanLbsSatelliteInfoRowStatus
}
STATUS current
DESCRIPTION
"A collection of common objects for
Cellular Location Based Service."
::= { ciscoWan3gMIBGroups 5 }
ciscoWan3gMIBSmsObjectGroup OBJECT-GROUP
OBJECTS {
c3gSmsServiceAvailable,
c3gSmsOutSmsCount,
c3gSmsOutSmsErrorCount,
c3gSmsInSmsStorageUsed,
c3gSmsInSmsStorageUnused,
c3gSmsInSmsArchiveCount,
c3gSmsInSmsArchiveErrorCount,
c3gSmsInSmsArchived,
c3gSmsArchiveUrl,
c3gSmsOutSmsStatus,
c3gSmsInSmsCount,
c3gSmsInSmsDeleted,
c3gSmsInSmsStorageMax,
c3gSmsInSmsCallBack,
c3gSmsOutSmsPendingCount,
c3gSmsOutSmsArchiveCount,
c3gSmsOutSmsArchiveErrorCount
}
STATUS current
DESCRIPTION
"A collection of common objects for
Cellular Short Messaging Service."
::= { ciscoWan3gMIBGroups 6 }
ciscoWan3gMIBNotificationGroupRev1 NOTIFICATION-GROUP
NOTIFICATIONS {
c3gModemUpNotif,
c3gModemDownNotif,
c3gServiceChangedNotif,
c3gNetworkChangedNotif,
c3gConnectionStatusChangedNotif,
c3gRssiOnsetNotif,
c3gEcIoOnsetNotif,
c3gRssiAbateNotif,
c3gEcIoAbateNotif,
c3gModemTemperOnsetNotif,
c3gModemTemperAbateNotif,
c3gModemTemperOnsetRecoveryNotif,
c3gModemTemperAbateRecoveryNotif
}
STATUS current
DESCRIPTION
"A collection of objects for Cellular WAN notifications."
::= { ciscoWan3gMIBGroups 7 }
END
Reference in New Issue View Git Blame Copy Permalink