mirror of
https://github.com/librenms/librenms.git
synced 2024-10-07 16:52:45 +00:00
6b9d05653c
git-svn-id: http://www.observium.org/svn/observer/trunk@1569 61d68cd4-352d-0410-923a-c4978735b2b8
1105 lines
39 KiB
Plaintext
1105 lines
39 KiB
Plaintext
ENTERASYS-CONVERGENCE-END-POINT-MIB DEFINITIONS ::= BEGIN
|
|
|
|
-- enterasys-convergence-end-point-mib.txt
|
|
--
|
|
-- Part Number:
|
|
--
|
|
--
|
|
|
|
-- This module provides authoritative definitions for Enterasys
|
|
-- Networks' Convergence End Point (CEP) MIB.
|
|
|
|
--
|
|
-- This module will be extended, as needed.
|
|
|
|
-- Enterasys Networks reserves the right to make changes in this
|
|
-- specification and other information contained in this document
|
|
-- without prior notice. The reader should consult Enterasys Networks
|
|
-- to determine whether any such changes have been made.
|
|
--
|
|
-- In no event shall Enterasys Networks be liable for any incidental,
|
|
-- indirect, special, or consequential damages whatsoever (including
|
|
-- but not limited to lost profits) arising out of or related to this
|
|
-- document or the information contained in it, even if Enterasys
|
|
-- Networks has been advised of, known, or should have known, the
|
|
-- possibility of such damages.
|
|
--
|
|
-- Enterasys Networks grants vendors, end-users, and other interested
|
|
-- parties a non-exclusive license to use this Specification in
|
|
-- connection with the management of Enterasys Networks products.
|
|
|
|
-- Copyright November, (2003-2005) Enterasys Networks, Inc.
|
|
|
|
IMPORTS
|
|
MODULE-IDENTITY, OBJECT-TYPE, Integer32
|
|
FROM SNMPv2-SMI
|
|
TEXTUAL-CONVENTION, RowStatus, MacAddress, DateAndTime, TruthValue
|
|
FROM SNMPv2-TC
|
|
MODULE-COMPLIANCE, OBJECT-GROUP
|
|
FROM SNMPv2-CONF
|
|
ifIndex, InterfaceIndex
|
|
FROM IF-MIB
|
|
InetAddressType, InetAddress
|
|
FROM INET-ADDRESS-MIB
|
|
EnabledStatus
|
|
FROM P-BRIDGE-MIB
|
|
SnmpAdminString
|
|
FROM SNMP-FRAMEWORK-MIB
|
|
etsysModules
|
|
FROM ENTERASYS-MIB-NAMES;
|
|
|
|
etsysConvergenceEndPointMIB MODULE-IDENTITY
|
|
LAST-UPDATED "200511181325Z" -- Fri Nov 18 13:25 UTC 2005
|
|
ORGANIZATION "Enterasys Networks, Inc"
|
|
CONTACT-INFO
|
|
"Postal: Enterasys Networks
|
|
50 Minuteman Rd.
|
|
Andover, MA 01810-1008
|
|
USA
|
|
Phone: +1 978 684 1000
|
|
E-mail: support@enterasys.com
|
|
WWW: http://www.enterasys.com"
|
|
|
|
DESCRIPTION
|
|
"This MIB module defines a portion of the SNMP MIB under
|
|
Enterasys Networks enterprise OID pertaining to
|
|
Convergence End Point management."
|
|
|
|
REVISION "200511181325Z" -- Fri Nov 18 13:25 UTC 2005
|
|
DESCRIPTION
|
|
"Added new ConvEndPointType of lldpMed(6)."
|
|
|
|
REVISION "200510191549Z" -- Wed Oct 19 15:49 UTC 2005
|
|
DESCRIPTION
|
|
"Added the etsysCEPCiscoCDPVoicePortVlan to configure the remote
|
|
configuration of Cisco VOIP phones using Cisco CDP."
|
|
|
|
REVISION "200508161233Z" -- Tue Aug 16 12:33 UTC 2005
|
|
DESCRIPTION
|
|
"Added new etsysConvEndPointDetectionEndPointType enumeration
|
|
of sip(2)."
|
|
|
|
REVISION "200506161427Z" -- Thu Jun 16 14:27 UTC 2005
|
|
DESCRIPTION
|
|
"Added new ConvEndPointType of sip(5). Added new default
|
|
behavior to etsysConvEndPointDetectionTable for SIP."
|
|
|
|
REVISION "200503311610Z" -- Thu Mar 31 16:10 GMT 2005
|
|
DESCRIPTION
|
|
"Deprecated the etsysConvEndPointConnMacTable in favor of
|
|
the more flexible etsysCEPConnMacTable. The
|
|
etsysCEPPortClearUsers object has been added to allow easier
|
|
clearing of detected Convergence End Points on a per port
|
|
basis."
|
|
|
|
REVISION "200311051942Z" -- Wed Nov 5 19:42 GMT 2003
|
|
DESCRIPTION
|
|
"The initial version of this MIB module."
|
|
::= { etsysModules 40 }
|
|
|
|
|
|
-- -------------------------------------------------------------
|
|
-- Textual conventions
|
|
-- -------------------------------------------------------------
|
|
|
|
ConvEndPointTypes ::= TEXTUAL-CONVENTION
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Supported Convergence End Point products."
|
|
SYNTAX BITS {
|
|
ciscoIPphone(0),
|
|
siemensIPphone(1),
|
|
avayaCLan(2),
|
|
avayaMedPro(3),
|
|
genericH323(4),
|
|
sip(5),
|
|
lldpMed(6)
|
|
}
|
|
|
|
|
|
-- -------------------------------------------------------------
|
|
-- MIB Objects
|
|
-- -------------------------------------------------------------
|
|
|
|
etsysConvEndPointObjects OBJECT IDENTIFIER
|
|
::= { etsysConvergenceEndPointMIB 1 }
|
|
|
|
etsysConvEndPointConfig OBJECT IDENTIFIER
|
|
::= { etsysConvEndPointObjects 1 }
|
|
|
|
etsysConvEndPointStatus OBJECT IDENTIFIER
|
|
::= { etsysConvEndPointObjects 2 }
|
|
|
|
etsysConvEndPointDetection OBJECT IDENTIFIER
|
|
::= { etsysConvEndPointObjects 3 }
|
|
|
|
|
|
-- -------------------------------------------------------------
|
|
-- Convergence End Point Configuration Group
|
|
-- -------------------------------------------------------------
|
|
|
|
etsysConvEndPointGlobalConfigEnable OBJECT-TYPE
|
|
SYNTAX EnabledStatus
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"When set to enabled(1) this object activates the current
|
|
Convergence End Point configuration.
|
|
|
|
When set to disabled(2) this MIB SHALL be configurable,
|
|
but MUST NOT be applied, all entries will be removed
|
|
from the etsysConvEndPointConnMacTable and the
|
|
etsysConvEndPointConnPortTable, and any policies that
|
|
have been changed as a result of End Point detection
|
|
will revert to their default states.
|
|
|
|
Maintaining the value of this object across agent
|
|
reboots is REQUIRED."
|
|
DEFVAL { disabled }
|
|
::= { etsysConvEndPointConfig 1 }
|
|
|
|
|
|
-- -------------------------------------------------------------
|
|
-- Convergence End Point Global Configuration Table
|
|
-- -------------------------------------------------------------
|
|
|
|
etsysConvEndPointGlobalConfigTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF EtsysConvEndPointGlobalConfigEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This table represents all Convergence End Point types
|
|
supported by this entity, and provides a default policy
|
|
profile for each Convergence End Point type."
|
|
::= { etsysConvEndPointConfig 2 }
|
|
|
|
etsysConvEndPointGlobalConfigEntry OBJECT-TYPE
|
|
SYNTAX EtsysConvEndPointGlobalConfigEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Defines the default policy to be applied when this type of
|
|
Convergence End Point is detected or discovered."
|
|
INDEX { etsysConvEndPointGlobalEndPointType }
|
|
::= { etsysConvEndPointGlobalConfigTable 1 }
|
|
|
|
EtsysConvEndPointGlobalConfigEntry ::=
|
|
SEQUENCE {
|
|
etsysConvEndPointGlobalEndPointType ConvEndPointTypes,
|
|
etsysConvEndPointGlobalDefaultPolicyIndex Integer32
|
|
}
|
|
|
|
etsysConvEndPointGlobalEndPointType OBJECT-TYPE
|
|
SYNTAX ConvEndPointTypes
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The Convergence End Point type. The value of this object is
|
|
limited to a single enumerated bit in the ConvEndPointTypes
|
|
textual convention."
|
|
::= { etsysConvEndPointGlobalConfigEntry 1 }
|
|
|
|
etsysConvEndPointGlobalDefaultPolicyIndex OBJECT-TYPE
|
|
SYNTAX Integer32 (0|1..65535)
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The policy that should be applied for this type of Convergence
|
|
End Point. This value is an etsysPolicyProfileIndex as defined
|
|
in the ENTERASYS-POLICY-PROFILE-MIB. If no such policy index
|
|
exists, then no policy will be applied when this type of
|
|
Convergence End Point is detected or discovered. The value
|
|
zero is not a valid etsysPolicyProfileIndex, so zero indicates
|
|
that no policy should be applied.
|
|
|
|
Maintaining the value of this object across system reboots
|
|
is REQUIRED."
|
|
DEFVAL { 0 }
|
|
::= { etsysConvEndPointGlobalConfigEntry 2 }
|
|
|
|
|
|
-- -------------------------------------------------------------
|
|
-- Convergence End Point Protocol Configuration Table
|
|
-- -------------------------------------------------------------
|
|
|
|
etsysConvEndPointProtocolConfigTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF EtsysConvEndPointProtocolConfigEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This table provides control of Convergence End Point detection
|
|
and discovery on a per interface and per Convergence End Point
|
|
type basis.
|
|
|
|
Maintaining the values of this table across system reboots
|
|
is REQUIRED."
|
|
::= { etsysConvEndPointConfig 3 }
|
|
|
|
etsysConvEndPointProtocolConfigEntry OBJECT-TYPE
|
|
SYNTAX EtsysConvEndPointProtocolConfigEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The current Convergence End Point detection and discovery
|
|
status for an interface."
|
|
INDEX { ifIndex, etsysConvEndPointProtocolEndPointType }
|
|
::= { etsysConvEndPointProtocolConfigTable 1 }
|
|
|
|
EtsysConvEndPointProtocolConfigEntry ::=
|
|
SEQUENCE {
|
|
etsysConvEndPointProtocolEndPointType ConvEndPointTypes,
|
|
etsysConvEndPointProtocolEnable EnabledStatus
|
|
}
|
|
|
|
etsysConvEndPointProtocolEndPointType OBJECT-TYPE
|
|
SYNTAX ConvEndPointTypes
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The Convergence End Point type."
|
|
::= { etsysConvEndPointProtocolConfigEntry 1 }
|
|
|
|
etsysConvEndPointProtocolEnable OBJECT-TYPE
|
|
SYNTAX EnabledStatus
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"When set to enabled(1), Convergence End Point detection
|
|
and discovery will be enabled on this interface for the
|
|
Convergence End Point type specified.
|
|
When set to disabled(2), the Convergence End Points that
|
|
have been discovered or detected on this interface of the
|
|
type specified will be removed from the
|
|
etsysConvEndPointConnMacTable and the
|
|
etsysConvEndPointConnPortTable.
|
|
After all of the End Points have been removed from an
|
|
interface the policy on that interface will revert to
|
|
its default state."
|
|
DEFVAL { disabled }
|
|
::= { etsysConvEndPointProtocolConfigEntry 2 }
|
|
|
|
|
|
-- -------------------------------------------------------------
|
|
-- Convergence End Point Connection MAC Table
|
|
-- -------------------------------------------------------------
|
|
|
|
etsysConvEndPointConnMacTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF EtsysConvEndPointConnMacEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS deprecated
|
|
DESCRIPTION
|
|
"This table provides information on each of the Convergence
|
|
End Points that has been discovered or detected by this
|
|
entity.
|
|
|
|
Maintaining the value of this object across system reboots
|
|
is NOT REQUIRED."
|
|
::= { etsysConvEndPointStatus 1 }
|
|
|
|
etsysConvEndPointConnMacEntry OBJECT-TYPE
|
|
SYNTAX EtsysConvEndPointConnMacEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS deprecated
|
|
DESCRIPTION
|
|
"Information about an individual Convergence End Point."
|
|
INDEX { etsysConvEndPointConnMacMacAddress }
|
|
::= { etsysConvEndPointConnMacTable 1 }
|
|
|
|
EtsysConvEndPointConnMacEntry ::=
|
|
SEQUENCE {
|
|
etsysConvEndPointConnMacMacAddress MacAddress,
|
|
etsysConvEndPointConnMacPortNumber InterfaceIndex,
|
|
etsysConvEndPointConnMacEndPointType ConvEndPointTypes,
|
|
etsysConvEndPointConnMacPolicyIndex Integer32,
|
|
etsysConvEndPointConnMacDiscoveryTime DateAndTime,
|
|
etsysConvEndPointConnMacFirmwareVersion SnmpAdminString,
|
|
etsysConvEndPointConnMacInetAddressType InetAddressType,
|
|
etsysConvEndPointConnMacInetAddress InetAddress
|
|
}
|
|
|
|
etsysConvEndPointConnMacMacAddress OBJECT-TYPE
|
|
SYNTAX MacAddress
|
|
MAX-ACCESS not-accessible
|
|
STATUS deprecated
|
|
DESCRIPTION
|
|
"The MAC address of this Convergence End Point."
|
|
::= { etsysConvEndPointConnMacEntry 1 }
|
|
|
|
etsysConvEndPointConnMacPortNumber OBJECT-TYPE
|
|
SYNTAX InterfaceIndex
|
|
MAX-ACCESS read-only
|
|
STATUS deprecated
|
|
DESCRIPTION
|
|
"The interface on which this Convergence End Point was
|
|
detected or discovered."
|
|
::= { etsysConvEndPointConnMacEntry 2 }
|
|
|
|
etsysConvEndPointConnMacEndPointType OBJECT-TYPE
|
|
SYNTAX ConvEndPointTypes
|
|
MAX-ACCESS read-only
|
|
STATUS deprecated
|
|
DESCRIPTION
|
|
"The type of Convergence End Point described by this row."
|
|
::= { etsysConvEndPointConnMacEntry 3 }
|
|
|
|
etsysConvEndPointConnMacPolicyIndex OBJECT-TYPE
|
|
SYNTAX Integer32
|
|
MAX-ACCESS read-only
|
|
STATUS deprecated
|
|
DESCRIPTION
|
|
"The policy applied for this Convergence End Point. This
|
|
value is an etsysPolicyProfileIndex as defined in the
|
|
ENTERASYS-POLICY-PROFILE-MIB. If the desired policy does
|
|
not currently exist, or never did exist, then a zero MUST
|
|
be returned."
|
|
::= { etsysConvEndPointConnMacEntry 4 }
|
|
|
|
etsysConvEndPointConnMacDiscoveryTime OBJECT-TYPE
|
|
SYNTAX DateAndTime
|
|
MAX-ACCESS read-only
|
|
STATUS deprecated
|
|
DESCRIPTION
|
|
"The time and date that this Convergence End Point was
|
|
detected or discovered."
|
|
::= { etsysConvEndPointConnMacEntry 5 }
|
|
|
|
etsysConvEndPointConnMacFirmwareVersion OBJECT-TYPE
|
|
SYNTAX SnmpAdminString (SIZE(0..32))
|
|
MAX-ACCESS read-only
|
|
STATUS deprecated
|
|
DESCRIPTION
|
|
"This is the firmware version of the discovered Convergence
|
|
End Point. If this information is not available via the
|
|
detection protocol then a zero length string MUST be returned."
|
|
DEFVAL { "" }
|
|
::= { etsysConvEndPointConnMacEntry 6 }
|
|
|
|
etsysConvEndPointConnMacInetAddressType OBJECT-TYPE
|
|
SYNTAX InetAddressType
|
|
MAX-ACCESS read-only
|
|
STATUS deprecated
|
|
DESCRIPTION
|
|
"The address type of the discovered or detected Convergence
|
|
End Point. If the address is unknown, then this object
|
|
MUST return 'unknown'."
|
|
DEFVAL { unknown }
|
|
::= { etsysConvEndPointConnMacEntry 7 }
|
|
|
|
etsysConvEndPointConnMacInetAddress OBJECT-TYPE
|
|
SYNTAX InetAddress
|
|
MAX-ACCESS read-only
|
|
STATUS deprecated
|
|
DESCRIPTION
|
|
"The address of the discovered or detected Convergence End
|
|
Point. If the address is unknown, then this object MUST
|
|
return a zero length string."
|
|
DEFVAL { "" }
|
|
::= { etsysConvEndPointConnMacEntry 8 }
|
|
|
|
|
|
-- -------------------------------------------------------------
|
|
-- Convergence End Point Connection Port Table
|
|
-- -------------------------------------------------------------
|
|
|
|
etsysConvEndPointConnPortTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF EtsysConvEndPointConnPortEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This table provides a mapping from the entities interfaces
|
|
to discovered Convergence End Points.
|
|
|
|
Maintaining the value of this object across system reboots
|
|
is NOT REQUIRED."
|
|
::= { etsysConvEndPointStatus 2 }
|
|
|
|
etsysConvEndPointConnPortEntry OBJECT-TYPE
|
|
SYNTAX EtsysConvEndPointConnPortEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Information about an individual Convergence End Point."
|
|
INDEX { ifIndex, etsysConvEndPointConnPortMacAddress }
|
|
::= { etsysConvEndPointConnPortTable 1 }
|
|
|
|
EtsysConvEndPointConnPortEntry ::=
|
|
SEQUENCE {
|
|
etsysConvEndPointConnPortMacAddress MacAddress
|
|
}
|
|
|
|
etsysConvEndPointConnPortMacAddress OBJECT-TYPE
|
|
SYNTAX MacAddress
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The MAC address of the discovered or detected Convergence
|
|
End Point."
|
|
::= { etsysConvEndPointConnPortEntry 1 }
|
|
|
|
|
|
-- -------------------------------------------------------------
|
|
-- New Convergence End Point (CEP) Connection MAC Table
|
|
-- -------------------------------------------------------------
|
|
|
|
etsysCEPConnMacTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF EtsysCEPConnMacEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This table provides information on each of the Convergence
|
|
End Points that has been discovered or detected by this
|
|
entity.
|
|
|
|
Maintaining the value of this object across system reboots
|
|
is NOT REQUIRED."
|
|
::= { etsysConvEndPointStatus 3 }
|
|
|
|
etsysCEPConnMacEntry OBJECT-TYPE
|
|
SYNTAX EtsysCEPConnMacEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Information about an individual Convergence End Point (CEP)."
|
|
INDEX { etsysConvEndPointConnPortMacAddress, ifIndex }
|
|
::= { etsysCEPConnMacTable 1 }
|
|
|
|
EtsysCEPConnMacEntry ::=
|
|
SEQUENCE {
|
|
etsysCEPConnMacEndPointType ConvEndPointTypes,
|
|
etsysCEPConnMacPolicyIndex Integer32,
|
|
etsysCEPConnMacDiscoveryTime DateAndTime,
|
|
etsysCEPConnMacFirmwareVersion SnmpAdminString,
|
|
etsysCEPConnMacInetAddressType InetAddressType,
|
|
etsysCEPConnMacInetAddress InetAddress
|
|
}
|
|
|
|
etsysCEPConnMacEndPointType OBJECT-TYPE
|
|
SYNTAX ConvEndPointTypes
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The type of Convergence End Point described by this row."
|
|
::= { etsysCEPConnMacEntry 1 }
|
|
|
|
etsysCEPConnMacPolicyIndex OBJECT-TYPE
|
|
SYNTAX Integer32 (0|1..65535)
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The policy applied for this Convergence End Point. This
|
|
value is an etsysPolicyProfileIndex as defined in the
|
|
ENTERASYS-POLICY-PROFILE-MIB. If the desired policy does
|
|
not currently exist, or never did exist, then a zero MUST
|
|
be returned."
|
|
::= { etsysCEPConnMacEntry 2 }
|
|
|
|
etsysCEPConnMacDiscoveryTime OBJECT-TYPE
|
|
SYNTAX DateAndTime
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The time and date that this Convergence End Point was
|
|
detected or discovered."
|
|
::= { etsysCEPConnMacEntry 3 }
|
|
|
|
etsysCEPConnMacFirmwareVersion OBJECT-TYPE
|
|
SYNTAX SnmpAdminString (SIZE(0..32))
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This is the firmware version of the discovered Convergence
|
|
End Point. If this information is not available via the
|
|
detection protocol then a zero length string MUST be returned."
|
|
DEFVAL { "" }
|
|
::= { etsysCEPConnMacEntry 4 }
|
|
|
|
etsysCEPConnMacInetAddressType OBJECT-TYPE
|
|
SYNTAX InetAddressType
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The address type of the discovered or detected Convergence
|
|
End Point. If the address is unknown, then this object
|
|
MUST return 'unknown'."
|
|
DEFVAL { unknown }
|
|
::= { etsysCEPConnMacEntry 5 }
|
|
|
|
etsysCEPConnMacInetAddress OBJECT-TYPE
|
|
SYNTAX InetAddress
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The address of the discovered or detected Convergence End
|
|
Point. If the address is unknown, then this object MUST
|
|
return a zero length string."
|
|
DEFVAL { "" }
|
|
::= { etsysCEPConnMacEntry 6 }
|
|
|
|
|
|
-- -------------------------------------------------------------
|
|
-- Convergence End Point Detection Table
|
|
-- -------------------------------------------------------------
|
|
|
|
etsysConvEndPointDetectionMaxEntries OBJECT-TYPE
|
|
SYNTAX Integer32
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This value represents the maximum number of entries
|
|
allowed in the etsysConvEndPointDetectionTable."
|
|
::= { etsysConvEndPointDetection 1 }
|
|
|
|
etsysConvEndPointDetectionTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF EtsysConvEndPointDetectionEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"A table that describes the IP address and IP port based
|
|
Convergence End Point detection parameters.
|
|
|
|
Packets on interfaces that are configured to detect End
|
|
Points, via the etsysConvEndPointProtocolConfigTable,
|
|
that are defined in this table are inspected to determine
|
|
if a Convergence End Point exists on that interface.
|
|
|
|
Rules applying to Convergence End Point types that are
|
|
configured for detection are evaluated according to the
|
|
following:
|
|
|
|
1. If etsysConvEndPointDetectionProtocol does not have
|
|
any bits set, this indicates that the port based detection
|
|
should not be performed, proceed to step 2. Otherwise
|
|
the value in etsysConvEndPointDetectionProtocol is
|
|
evaluated against the protocol field in the IP header,
|
|
if it is of a, or the, type specified then the destination
|
|
port must be between the values of
|
|
etsysConvEndPointDetectionPortLow and
|
|
etsysConvEndPointDetectionPortHigh, inclusive.
|
|
|
|
2. If the etsysConvEndPointDetectionAddr is null, this
|
|
indicates that no detection address check should be
|
|
performed, consider the End Point detected. Otherwise
|
|
the value the of etsysConvEndPointDetectionAddr will be
|
|
masked with the value of etsysConvEndPointDetectionAddrMask,
|
|
via a bitwise AND operation, and this value will be compared
|
|
with the destination IP address that has also been masked
|
|
with the value of etsysConvEndPointDetectionAddrMask,
|
|
via a bitwise AND operation, if they are equal then
|
|
consider the End Point detected.
|
|
|
|
If there are no rows in this table that are in the active
|
|
state then the following pseudo entries describe the
|
|
behavior of the IP based Convergence End Point detection.
|
|
|
|
EndPointType siemens
|
|
Protocol { { udp, tcp } }
|
|
PortLow 4060
|
|
PortHigh 4060
|
|
AddrType unknown
|
|
Addr ''
|
|
AddrMaskType unknown
|
|
AddrMask ''
|
|
|
|
EndPointType h323
|
|
Protocol { { udp, tcp } }
|
|
PortLow 1718
|
|
PortHigh 1720
|
|
AddrType ipv4
|
|
Addr '224.0.1.41'
|
|
AddrMaskType ipv4
|
|
AddrMask '255.255.255.255'
|
|
|
|
EndPointType sip
|
|
Protocol { { udp, tcp } }
|
|
PortLow 5060
|
|
PortHigh 5060
|
|
AddrType ipv4
|
|
Addr '224.0.1.75'
|
|
AddrMaskType ipv4
|
|
AddrMask '255.255.255.255'
|
|
|
|
If one or more entries in this table are active the active
|
|
entries will define the IP based detection behavior in its
|
|
entirety.
|
|
|
|
Maintaining entries in this table across system reboots is
|
|
REQUIRED for entries with an etsysConvEndPointDetectionRowStatus
|
|
value of active(1)."
|
|
REFERENCE
|
|
"Internet Assigned Numbers Authority (INTERNET MULTICAST
|
|
ADDRESSES).
|
|
RFC3261 (SIP: Session Initiation Protocol)."
|
|
::= { etsysConvEndPointDetection 2 }
|
|
|
|
etsysConvEndPointDetectionEntry OBJECT-TYPE
|
|
SYNTAX EtsysConvEndPointDetectionEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Each entry represents a describes parameters for
|
|
detecting a Convergence End Point."
|
|
INDEX { etsysConvEndPointDetectionRuleIndex }
|
|
::= { etsysConvEndPointDetectionTable 1 }
|
|
|
|
EtsysConvEndPointDetectionEntry ::=
|
|
SEQUENCE {
|
|
etsysConvEndPointDetectionRuleIndex Integer32,
|
|
etsysConvEndPointDetectionEndPointType INTEGER,
|
|
etsysConvEndPointDetectionProtocol BITS,
|
|
etsysConvEndPointDetectionPortLow Integer32,
|
|
etsysConvEndPointDetectionPortHigh Integer32,
|
|
etsysConvEndPointDetectionAddrType InetAddressType,
|
|
etsysConvEndPointDetectionAddr InetAddress,
|
|
etsysConvEndPointDetectionAddrMaskType InetAddressType,
|
|
etsysConvEndPointDetectionAddrMask InetAddress,
|
|
etsysConvEndPointDetectionRowStatus RowStatus
|
|
}
|
|
|
|
etsysConvEndPointDetectionRuleIndex OBJECT-TYPE
|
|
SYNTAX Integer32 (1..2147483647)
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The index of this conceptual row. This row represents a
|
|
single rule for determining if an incoming IP packet
|
|
indicates the presence of a Convergence End Point device.
|
|
The lower the numerical value of the index the greater the
|
|
precedence of the rule. It is recommended that the lowest
|
|
index be configured to most predominate protocol in the
|
|
network for greater efficiency."
|
|
::={ etsysConvEndPointDetectionEntry 1 }
|
|
|
|
etsysConvEndPointDetectionEndPointType OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
h323(0),
|
|
siemens(1),
|
|
sip(2)
|
|
}
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The Convergence End Point device type that a 'hit' on
|
|
this rule will indicate the presence of."
|
|
DEFVAL { siemens }
|
|
::={ etsysConvEndPointDetectionEntry 2 }
|
|
|
|
etsysConvEndPointDetectionProtocol OBJECT-TYPE
|
|
SYNTAX BITS {
|
|
udp(0),
|
|
tcp(1)
|
|
}
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The IP protocol type that the following port range
|
|
applies to. If no bits are set then the destination
|
|
port will not be evaluated as part of the detection
|
|
process."
|
|
DEFVAL { { udp, tcp } }
|
|
::={ etsysConvEndPointDetectionEntry 3 }
|
|
|
|
etsysConvEndPointDetectionPortLow OBJECT-TYPE
|
|
SYNTAX Integer32 (1..65535)
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The low end of the range of the IP destination port that
|
|
will be used for Convergence End Point detection. This
|
|
value represents the low value in a range of port numbers
|
|
that will be used to indicate this type of Convergence End
|
|
Point. This value must be less than or equal to
|
|
etsysConvEndPointDetectionPortHigh."
|
|
DEFVAL { 4060 }
|
|
::={ etsysConvEndPointDetectionEntry 4 }
|
|
|
|
etsysConvEndPointDetectionPortHigh OBJECT-TYPE
|
|
SYNTAX Integer32 (1..65535)
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The high end of the range of the IP destination port that
|
|
will be used for Convergence End Point detection. This
|
|
value represents the high value in a range of port numbers
|
|
that will be used to indicate this type of Convergence End
|
|
Point. This value must be greater than or equal to
|
|
etsysConvEndPointDetectionPortLow."
|
|
DEFVAL { 4060 }
|
|
::={ etsysConvEndPointDetectionEntry 5 }
|
|
|
|
etsysConvEndPointDetectionAddrType OBJECT-TYPE
|
|
SYNTAX InetAddressType
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The destination address type that will be used for Convergence
|
|
End Point detection. If the address type is 'unknown', then
|
|
this value will not be evaluated as part of the detection
|
|
process."
|
|
DEFVAL { unknown }
|
|
::={ etsysConvEndPointDetectionEntry 6 }
|
|
|
|
etsysConvEndPointDetectionAddr OBJECT-TYPE
|
|
SYNTAX InetAddress
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The destination IP address that will be used for Convergence
|
|
End Point detection. If this address is null, then this value
|
|
will not be evaluated as part of the detection process."
|
|
DEFVAL { "" }
|
|
::={ etsysConvEndPointDetectionEntry 7 }
|
|
|
|
etsysConvEndPointDetectionAddrMaskType OBJECT-TYPE
|
|
SYNTAX InetAddressType
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The address type of the mask that will be applied to the
|
|
destination IP address as part of the Convergence End Point
|
|
detection process. If the address type is 'unknown', then
|
|
this value will not be evaluated as part of the detection
|
|
process."
|
|
DEFVAL { unknown }
|
|
::={ etsysConvEndPointDetectionEntry 8 }
|
|
|
|
etsysConvEndPointDetectionAddrMask OBJECT-TYPE
|
|
SYNTAX InetAddress
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The destination address mask that will be used for Convergence
|
|
End Point detection. If the mask is null, then this value will
|
|
not be evaluated as part of the detection process."
|
|
DEFVAL { "" }
|
|
::={ etsysConvEndPointDetectionEntry 9 }
|
|
|
|
etsysConvEndPointDetectionRowStatus OBJECT-TYPE
|
|
SYNTAX RowStatus
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The status of this row as defined by the RowStatus textual
|
|
convention.
|
|
|
|
Rows in this table can only transition to 'notInService',
|
|
or to 'active' if the etsysConvEndPointDetectionAddrType
|
|
object and the etsysConvEndPointDetectionAddrMaskType
|
|
object have the same value, and either their values are
|
|
not 'unknown' or there is at least one bit set in the
|
|
etsysConvEndPointDetectionProtocol object."
|
|
REFERENCE
|
|
"RFC2579 (Textual Conventions for SMIv2)"
|
|
::={ etsysConvEndPointDetectionEntry 10 }
|
|
|
|
|
|
-- -------------------------------------------------------------
|
|
-- Convergence End Point Detection Port Configuration Table
|
|
-- -------------------------------------------------------------
|
|
|
|
etsysCEPDetectionPortConfigTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF EtsysCEPDetectionPortConfigEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"A table of per port configuration for Convergence End Point
|
|
detection.
|
|
|
|
Maintaining the value of this object across system reboots
|
|
is NOT REQUIRED."
|
|
::= { etsysConvEndPointDetection 3 }
|
|
|
|
etsysCEPDetectionPortConfigEntry OBJECT-TYPE
|
|
SYNTAX EtsysCEPDetectionPortConfigEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"An entry containing per port Convergence End Point data.
|
|
Only interfaces that are able to detect Convergence End Points
|
|
are represented in this table."
|
|
INDEX { ifIndex }
|
|
::= { etsysCEPDetectionPortConfigTable 1 }
|
|
|
|
EtsysCEPDetectionPortConfigEntry ::=
|
|
SEQUENCE {
|
|
etsysCEPPortClearUsers TruthValue
|
|
}
|
|
|
|
etsysCEPPortClearUsers OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Setting this object to a value of true(1) will cause
|
|
all detected or discovered Convergence End Points to be
|
|
removed from the following status tables:
|
|
|
|
etsysConvEndPointConnMacTable
|
|
etsysConvEndPointConnPortTable
|
|
etsysCEPConnMacTable
|
|
|
|
Setting this object to a value of false(2) has no effect. This
|
|
object will always return a value of false(2)."
|
|
DEFVAL { false }
|
|
::={ etsysCEPDetectionPortConfigEntry 1 }
|
|
|
|
-- -------------------------------------------------------------
|
|
-- Convergence End Point CDP Port Configuration Table
|
|
-- -------------------------------------------------------------
|
|
|
|
etsysCEPCdpPortConfigTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF EtsysCEPCdpPortConfigEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"A table of per port configuration for Convergence End Point
|
|
detection related to the Cisco CDP protocol. Only ports
|
|
that are capable of participating in Cisco CDP protocol are
|
|
represented in this table."
|
|
::= { etsysConvEndPointDetection 4 }
|
|
|
|
etsysCEPCdpPortConfigEntry OBJECT-TYPE
|
|
SYNTAX EtsysCEPCdpPortConfigEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"An entry containing per port Convergence End Point data.
|
|
Only interfaces that are able to detect Convergence End Points
|
|
are represented in this table."
|
|
INDEX { ifIndex }
|
|
::= { etsysCEPCdpPortConfigTable 1 }
|
|
|
|
EtsysCEPCdpPortConfigEntry ::=
|
|
SEQUENCE {
|
|
etsysCEPCiscoCDPVoicePortVlan Integer32
|
|
}
|
|
|
|
etsysCEPCiscoCDPVoicePortVlan OBJECT-TYPE
|
|
SYNTAX Integer32 (-1|0|1..4094|4095)
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object controls the behavior of the remote configuration
|
|
of Cisco VOIP phones via Cisco CDP. Setting this object to
|
|
a value of -1 will cause the device to not attempt to
|
|
remotely configure a Cisco phone using CDP. Setting this
|
|
object to a value of 0 will cause the device to configure
|
|
the phone to send 802.1p priority tagged frames. A value of
|
|
4095 will cause the device to configure the phone to send
|
|
untagged frames. A value in the range 1..4094 will cause
|
|
the device to configure the phone to send 802.1Q tagged frames
|
|
using that value as the VLAN ID encoded in the tag. This object
|
|
SHOULD be maintained across device reboots."
|
|
DEFVAL { -1 }
|
|
::={ etsysCEPCdpPortConfigEntry 1 }
|
|
|
|
|
|
-- -------------------------------------------------------------
|
|
-- Conformance Information
|
|
-- -------------------------------------------------------------
|
|
|
|
etsysConvEndPointConformance OBJECT IDENTIFIER
|
|
::= { etsysConvergenceEndPointMIB 2 }
|
|
|
|
etsysConvEndPointGroups OBJECT IDENTIFIER
|
|
::= { etsysConvEndPointConformance 1 }
|
|
|
|
etsysConvEndPointCompliances OBJECT IDENTIFIER
|
|
::= { etsysConvEndPointConformance 2 }
|
|
|
|
|
|
-- -------------------------------------------------------------
|
|
-- Units of conformance
|
|
-- -------------------------------------------------------------
|
|
|
|
etsysConvEndPointGlobalConfigGroup OBJECT-GROUP
|
|
OBJECTS {
|
|
etsysConvEndPointGlobalConfigEnable,
|
|
etsysConvEndPointGlobalDefaultPolicyIndex
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Objects which provide global control of the Convergence
|
|
End Point features."
|
|
::= { etsysConvEndPointGroups 1 }
|
|
|
|
etsysConvEndPointConfigGroup OBJECT-GROUP
|
|
OBJECTS {
|
|
etsysConvEndPointProtocolEnable
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Objects which provide overrides to the global Convergence
|
|
End Point controls."
|
|
::= { etsysConvEndPointGroups 2 }
|
|
|
|
etsysConvEndPointDetectionGroup OBJECT-GROUP
|
|
OBJECTS {
|
|
etsysConvEndPointDetectionEndPointType,
|
|
etsysConvEndPointDetectionProtocol,
|
|
etsysConvEndPointDetectionPortLow,
|
|
etsysConvEndPointDetectionPortHigh,
|
|
etsysConvEndPointDetectionAddrType,
|
|
etsysConvEndPointDetectionAddr,
|
|
etsysConvEndPointDetectionAddrMaskType,
|
|
etsysConvEndPointDetectionAddrMask,
|
|
etsysConvEndPointDetectionRowStatus
|
|
}
|
|
STATUS deprecated
|
|
DESCRIPTION
|
|
"Objects that provide configuration information specific to
|
|
IP, port, and address based Convergence End Point detection."
|
|
::= { etsysConvEndPointGroups 3 }
|
|
|
|
etsysConvEndPointStatusGroup OBJECT-GROUP
|
|
OBJECTS {
|
|
etsysConvEndPointConnMacPortNumber,
|
|
etsysConvEndPointConnMacEndPointType,
|
|
etsysConvEndPointConnMacPolicyIndex,
|
|
etsysConvEndPointConnMacDiscoveryTime,
|
|
etsysConvEndPointConnMacFirmwareVersion,
|
|
etsysConvEndPointConnMacInetAddressType,
|
|
etsysConvEndPointConnMacInetAddress,
|
|
etsysConvEndPointConnPortMacAddress
|
|
}
|
|
STATUS deprecated
|
|
DESCRIPTION
|
|
"Objects that provide status information for discovered
|
|
and detected Convergence End Points."
|
|
::= { etsysConvEndPointGroups 4 }
|
|
|
|
etsysConvEndPointStatusGroup2 OBJECT-GROUP
|
|
OBJECTS {
|
|
etsysConvEndPointConnPortMacAddress,
|
|
etsysCEPConnMacEndPointType,
|
|
etsysCEPConnMacPolicyIndex,
|
|
etsysCEPConnMacDiscoveryTime,
|
|
etsysCEPConnMacFirmwareVersion,
|
|
etsysCEPConnMacInetAddressType,
|
|
etsysCEPConnMacInetAddress
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Objects that provide status information for discovered
|
|
and detected Convergence End Points."
|
|
::= { etsysConvEndPointGroups 5 }
|
|
|
|
etsysConvEndPointDetectionGroup2 OBJECT-GROUP
|
|
OBJECTS {
|
|
etsysConvEndPointDetectionEndPointType,
|
|
etsysConvEndPointDetectionProtocol,
|
|
etsysConvEndPointDetectionPortLow,
|
|
etsysConvEndPointDetectionPortHigh,
|
|
etsysConvEndPointDetectionAddrType,
|
|
etsysConvEndPointDetectionAddr,
|
|
etsysConvEndPointDetectionAddrMaskType,
|
|
etsysConvEndPointDetectionAddrMask,
|
|
etsysConvEndPointDetectionRowStatus,
|
|
etsysConvEndPointDetectionMaxEntries
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Objects that provide configuration information specific to
|
|
IP, port, and address based Convergence End Point detection."
|
|
::= { etsysConvEndPointGroups 6 }
|
|
|
|
etsysConvEndPointPortConfigGroup OBJECT-GROUP
|
|
OBJECTS {
|
|
etsysCEPPortClearUsers
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Objects that provide per port control for discovered
|
|
and detected Convergence End Points."
|
|
::= { etsysConvEndPointGroups 7 }
|
|
|
|
etsysConvEndPointCiscoVoiceVLANGroup OBJECT-GROUP
|
|
OBJECTS {
|
|
etsysCEPCiscoCDPVoicePortVlan
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Objects that provide per port control for configuring Cisco
|
|
VOIP phones via Cisco CDP."
|
|
::= { etsysConvEndPointGroups 8 }
|
|
|
|
-- -------------------------------------------------------------
|
|
-- Compliance statements
|
|
-- -------------------------------------------------------------
|
|
|
|
etsysConvEndPointCompliance MODULE-COMPLIANCE
|
|
STATUS deprecated
|
|
DESCRIPTION
|
|
"This compliance statement has been deprecated in favor of
|
|
the etsysConvEndPointCompliance2 group."
|
|
MODULE
|
|
MANDATORY-GROUPS {
|
|
etsysConvEndPointGlobalConfigGroup,
|
|
etsysConvEndPointStatusGroup
|
|
}
|
|
|
|
GROUP etsysConvEndPointConfigGroup
|
|
DESCRIPTION
|
|
"This group is mandatory for devices which support overrides
|
|
to device wide Policy Profiles."
|
|
|
|
GROUP etsysConvEndPointDetectionGroup
|
|
DESCRIPTION
|
|
"This group is mandatory for devices which support IP port
|
|
and address based Convergence End Point detection."
|
|
|
|
::= { etsysConvEndPointCompliances 1 }
|
|
|
|
etsysConvEndPointCompliance2 MODULE-COMPLIANCE
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The compliance statement for entities which implement
|
|
the Enterasys Convergence End Point Management MIB."
|
|
MODULE
|
|
MANDATORY-GROUPS {
|
|
etsysConvEndPointGlobalConfigGroup,
|
|
etsysConvEndPointStatusGroup2
|
|
}
|
|
|
|
GROUP etsysConvEndPointConfigGroup
|
|
DESCRIPTION
|
|
"This group is mandatory for devices which support overrides
|
|
to device wide policy profiles."
|
|
|
|
GROUP etsysConvEndPointDetectionGroup2
|
|
DESCRIPTION
|
|
"This group is mandatory for devices which support IP, port,
|
|
and address based Convergence End Point detection."
|
|
|
|
::= { etsysConvEndPointCompliances 2 }
|
|
|
|
etsysConvEndPointPortConfigCompliance MODULE-COMPLIANCE
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The compliance statement for devices that support per port
|
|
configuration of Convergence End Point detection and
|
|
discovery."
|
|
MODULE
|
|
GROUP etsysConvEndPointPortConfigGroup
|
|
DESCRIPTION
|
|
"This group is mandatory for all devices that support per
|
|
port configuration of Convergence End Point detection and
|
|
discovery."
|
|
|
|
::= { etsysConvEndPointCompliances 3 }
|
|
|
|
etsysConvEndPointCiscoVoiceVLANCompliance MODULE-COMPLIANCE
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The compliance statement for devices that support detection
|
|
and configuration of Cisco VOIP phones via Cisco CDP."
|
|
MODULE
|
|
GROUP etsysConvEndPointCiscoVoiceVLANGroup
|
|
DESCRIPTION
|
|
"This group is mandatory for all devices that support
|
|
detection and configuration of Cisco VOIP phones via Cisco
|
|
CDP."
|
|
|
|
::= { etsysConvEndPointCompliances 4 }
|
|
|
|
END
|